Namco Cyber Cycles Dx Operators Manual

							Page 22
m e t Ino i t p i r c s e D
g n i t t e S o t u A ) a (. y l l a c i t a m o t u a h c t a m o t s t i n u d e k n i l l l a t s u j d a l l i W
e z i l a i t i n I y r o m e M p U k c a B ) b (at a d S D A l l a t e s e R
t s e T B C P ) c (BC P e m a G e h t g n i t s e t r o F
OTHERS
AUTO SETTING ................ (a)
BACK UP MEMORY INITIALIZE ................ (b)
PCB TEST ................ (c)
EXIT
BANK :CHOOSE
VIEW-SW:ENTER 6-3-7 Others
1. Select item (6) Others on the menu screen.
2. On entering Others the following screen will appear on the monitor.
m e t Ino i t p i r c s e D
n O r e w o P ) a (. n o d e h c t i w s n e e b s a h e n i h c a m s d n o c e s , s e t u n i m , s r u o h n i e m i t l a t o T
e m i T y a l P ) b (. y a l p n i n e e b s a h e n i h c a m t a h t s d n o c e s , s e t u n i m , s r u o h n i e m i t l a t o T
e v A e m i T y a l P ) c (.n o i t a r u d e m a g f o e m i t e g a r e v A
r e b m u N y a l P ) d (.s y a l p e m a g l a t o T
w e i V - e s r u o C ) e (.w e i v h c a e r o f e m i T
e k i B - e s r u o C ) f (. d e t c e l e s n e e b s a h e k i b a s e m i t f o r e b m u N
k n i L - e s r u o C ) g (.d e y a l p s e m a g d e k n i l f o r e b m u N
. P . C - e s r u o C ) h (.r e v o e m a g t a e s r u o c e h t n o n o i t i s o P
. T . P - e s r u o C ) i (. d e y a l p n e e b s a h e s r u o c h c a e e m i t l a t o T
e z i l a i t i n I ) j (.a t a d l l a t e s e R
a) If the game is linked, this option allows all linked positions to be set from position
No. 1 bike. If all game and coin options shown on the screen are correct, select
transmit, then push View Switch. All positions will automatically update to the
displayed options and ID No.  All screens will display the Auto Setting screen. Set
each bike colour from each Auto Setting screen.
Note: Any game in play will be lost during Auto Setting transmit. 
						

							Page 23
IN OUTIN OUT
6-4 Linking Two Machines.Up to two machines (4 bikes) can be linked together. 
The machines should be linked as described below. 
1) Ensure that the 
power is “OFF”.
2) Loosen the two screws (M5x12) on the back of the right monitor cabinet\
, and remove the connector cover.
3) Set the link switches to “ON” , “EXT”, and “ON”. (See Diag.)
4) Use the supplied link cable and connect the machines between “IN” and “OUT” sockets 
(See Diag.)
[Examples of Linked Machines] 
a) 2 Machines (4 Seats)
5) Turn the power to each machine “ON”, and set the PCB ID using the t\
est mode. (Refer to section 6-3-7,  “Others” Auto Setting (page 19))
Note:Settings other than those described will cause the machine to operate
incorrectly . 
						

							Page 24 6-4-1 Setting the Link Switches
The link switches are used to set the connection between seats and machines.
1). Setting only one machine (2 bikes)
Set the link switches to “ON”, “INT”, and
“ON”.
Note: Do not use a link cable.
2) Setting two or more machines.
Set the link switches to “ON”, “EXT”, and
“ON”.
3) Install the connector cover using
the two screws (M5x12).
The link procedure is now complete.
4) Setting for faulty PCB.
If the game PCB of only one bike is faulty, set the link on that bike to “OFF”
[Example of setting for faulty left side] 
						

							Page 25
7. MAINTENANCE
DANGER: In order to prevent injury or electric shock to service personnel, ensure
that the MAIN POWER IS OFF before attempting any maintenance.
DANGER: Before performing any work not described in this manual, be sure to
contact your distributor to receive instructions or answers to questions.
7-1 Replacing the Fluorescent Tube, Position, and Leading Driver Lamps
1) Remove the three security screws (M5x12), and remove the plexi upper retaining
bracket.
2) Remove the three security screws (M5x12), and remove the plexi lower retaining
bracket.
3) Remove the header plexi.
4) Unscrew the defective position lamp and replace.
Warning:- Ensure that the lamp is not hot before touching it.
7-2 Replacing the Signal Lamps
1) Remove five security screws (M5x12), and remove the signal plexi L or R.
2) Unscrew the defective lamp and replace.
Warning:- Ensure that the lamp is not hot before touching it. 
						

							Page 26
7-3 Handle Bar Assembly
Remove four M5X12 security screws, and remove handle bar assembly cover \
to gain 
access to the throttle and brake controls.
NOTE:- The game must be re-initialized whenever the PCB, ROMS, Throttle, Brake or
Steering controls are replaced. 
(See 7-4 Adjustments when Replacing Parts)
7-3-1 Replacing  the Throttle Control Pot 1) Slacken the grub screwM3X5 securing the 
control pot shaft to the
drive gear, and remove
the gear.
2) Replace the control pot ensuring that the wires
are replaced to the
correct terminals.
3) Turn the control pot shaft until the flat is
vertical and to the right,
when looking at the
shaft. Replace the drive
gear ensuring that the
control pot shaft does
not turn and the grub
screw in the drive gear
is on the flat of the shaft
4) Re-tighten the grub screw M3x5
7-3-2 Replacing the Brake Control Pot
1) Slacken the grub screw M3X5 securing the
control pot shaft to the
brake assembly.
2) Replace the control pot ensuring that the wires
are replaced to the
correct terminals.
3) When replacing the control pot, ensure that the flat on the control shaf\
t is in line with the grub screw.
4) Re-tighten the grub screw M3x5. 
						

							Page 27 7-3-3 Replacing the Steering Control Pot
1) Remove three security screws (M5X16) and four security screws (M5x12)
from the right hand bike vac-form, and remove the vac-form.
2) Slacken the grub screw (M4x5) to release the control pot shaft.
3) Replace the control pot, taking care that the wires are fitted to the correct
terminals.
4) Re-tighten the grub screw (M4x5), ensuring that it engages the flat of the
control pot shaft.
5) Refit the bike vac-form, and the security screws (M5x12) (M5x16). 
						

							Page 28
7-4 Adjustments When Replacing Parts (Initialization)
The following adjustments must always be carried out after replacing the\
 Game PCB, 
ROMS, or Throttle, Brake, and Steering Control Pots.
The game will not operate correctly if these adjustments are not made. 
1. Ensure that the Throttle and Brake are fully released and the bike is in\
 its central upright position.
2. Turn the Test switch on while pressing the Service switch. The following screen will be displayed.
3. Adjustment is complete when the screen displays Initialize Completed.
4. Operate the Brake and Throttle together to return to the Menu Screen.
5. Turn the Test switch OFF to return to normal game mode.
Note:- If the View Change button is flashing during standby mode, there is a
problem with one of the control pots (Throttle, Brake, or Bank) not be\
ing at zero.Enter Switch T est (See 6-3-3-1  Switch Test page 16) to determine which pot
is not at zero and either replace if faulty or reinitialize. 
						

							Page 29
8. PARTS 
						

							Page 30
M E T INO I T P I R C S E D.o N T R A P
1RO T I N O M N O I T C E J O R P R A E R  6 4 S P I L I H P3 0 0 0 0 0 4 8
2SS A L G T N O R F4 7 0 0 0 1 7 3
3)O G O L O C M A N / W ( E L L I R G R E K A E P S D U O L7 5 5 0 0 0 5 4
4PO T - N O I S N E T X E T E K C A R B R E V O C S U S2 6 5 0 0 0 5 4
5YL B M E S S A N O T T U B H S U P  T I L N E H W E L B A L I A V A T I D E R C5 1 2 0 0 2 0 6
6SH L - T N O R F N O I S N E T X E T E K C A R B R E V O C S U S6 5 5 0 0 0 5 4
8PO T - R E W O T N I O C T E K C A R B R E V O C S U S5 6 5 0 0 0 5 4
9SH L - T N O R F R E W O T N I O C T E K C A R B R E V O C S U S4 6 5 0 0 0 5 4
0 1A  T E K C A R B T N I O J E L C Y C5 5 5 0 0 0 5 4
1 1SH R - N O I S N E T X E T E K C A R B R E V O C S U S6 6 5 0 0 0 5 4
2 159 x 6 1 M T O O F E L B A T S U J D A9 7 0 0 0 3 8 8
3 1A 5 . v 2 1 A 0 3 / v 5 U S P M S4 0 0 0 0 0 3 8
O L B - O L S A 3  ¼ 1 E S U F7 4 5 0 0 5 3 6
O L B - O L S A 2  ¼ 1 E S U F6 0 5 0 0 5 3 6
O L B - K C I U Q A 2  ¼ 1 E S U F4 0 5 0 0 5 3 6
4 1mm 5 7 R O T S A C L E V I W S9 0 0 0 0 0 9 5
5 1Y S S A R E T L I F N I - S N I A M R E N F F A H C S6 1 0 0 0 0 6 6
A 5 m m 0 2 E S U F1 0 6 0 0 5 3 6
6 1TO O B R E N F F A H C S7 1 0 0 0 0 6 6
7 1RE K A E P S w 0 2  ½ 46 0 0 0 0 0 2 6
8 1RE W O L - T E K C A R B G N I N I A T E R S S A L G T N O R F2 5 4 0 0 0 5 4
9 1RE P P U - T E K C A R B G N I N I A T E R S S A L G T N O R F1 5 4 0 0 0 5 4
0 2PO T - L A C E D N O I S N E T X E T E N I B A C8 5 2 0 0 0 0 4
1 2SH L - L A C E D N O I S N E T X E T E N I B A C9 5 2 0 0 0 0 4
2 2SH R - L A C E D N O I S N E T X E T E N I B A C0 6 2 0 0 0 0 4
3 2SH R / S H L - L A C E D T E N I B A C R O T C E J O R P6 5 2 0 0 0 0 4
4 2PO T - L A C E D R E W O T N I O C1 6 2 0 0 0 0 4
5 2SH L - T A L F R E W O T N I O C T E K C A R B R E V O C S U S9 6 5 0 0 0 5 4
6 2SH R - T A L F R E W O T N I O C T E K C A R B R E V O C S U S0 7 5 0 0 0 5 4
7 2SH R T N O R F R E W O T N I O C T E K C A R B R E V O C S U S3 6 5 0 0 0 5 4
8 2.T . D . P . D H C T I W S K C O L R E T N I6 0 0 0 0 0 0 6
9 2RE V O C H C T I W S K C O L R E T N I8 2 0 0 0 0 9 3 
						

							Page 31