Namco Cyber Cycles Dx Operators Manual

							Page 12 4-4 Fitting the Header Assembly
To prevent injury, 
two people should be used to fit the Header Assembly.
1. The Header Assembly is heavy (approx. 25kg), with a forward centre of gravity,
so it is important that at least two people are used to fit or remove the Header
Assembly.
2. The fitting position of the Header Assembly is very high, and it is important that a
means of reaching the height safely, without stretching, is available. (e.g. steps,
step stools, etc.)
3. Place the Header Assembly on to the top of the cabinets and pass the loom
connectors into the monitor cabinet, taking care not to trap any wires.
4. Fit the 8off M8x20 Security Button Head Screws, Spring and Flat washers to
retain the Header Assembly to the cabinets.
Note:- Ensure that one person maintains the balance of the Header Assembly
while the screws are being fitted.
5. Connect the connectors inside the monitor cabinet.
NOTE:-
When the machine is fully assembled and in its final position, lower the 12 level
adjusters, (4 on each monitor cabinet and 2 on each bike assy), with a spanner so
that all castors are raised from the floor, and the machine is level.
Tighten the lock nuts with a spanner to ensure that the level adjusters do not move. 
						

							Page 13
5. HOW TO PLAY
This game is linkable so players can compete against each other on the same track,
or compete against computer bikes when playing alone. Two machines can be linked
together allowing up to four players to compete against each other.
The Header Assembly displays the position of each rider and also the leading rider.
Speed is controlled by use of the throttle and brake, and steering is controlled by
leaning the bike left or right.
After the insertion of a coin/s, credit is established to a bike position with the use of the
respective Credit Available button. Pressing the flashing View Change button,
located on the handle bar assembly, will display the  Course Select Screen.
There are two courses available, GREEN HILL is a practise course for beginners and
NEO YOKOHAMA is an intermediate and advanced course. In a linked game the
course is decided by the majority.
Next select a bike.
Each player can select one of three bikes:-
ANTHIAS, for beginners. It corners easily, and its top speed is reduced a little.
NVR750R, for intermediate. This bike has good cornering balance, and its top
speed is normal.
WILD  HOG  for advanced. By controlling the special drift, it can cover the course
faster than any of the other bikes, but is more difficult to control.
The first player to enter Bike Select is also able to select, by using the throttle, the
music during the game. The title is displayed in the lower left of the screen.
Players can join in a linked game during the link time countdown. This time can be
adjusted in the Game Options mode.
If a linked game is in progress but a bike position is available, a player can use this
position as a solo game.
When a player completes the specified number of laps in the given time, they
complete the game. If the countdown timer reaches 00 before completing the specified
number of laps the game is over. At the end of the game, the players ranking, fastest
lap time and total time are displayed.
If a best time is beaten the end of the race will be shown and the player can enter their
initials by leaning the bike to select the letters and pressing View Change to enter
them.
With this game it is possible to change the players viewpoint of the game. Each time
the View Change button is pressed the view changes between : Pillion View,
Riders View, and Behind View. 
						

							Page 14
6. ADJUSTMENTS
6-1 Turning on the PowerAfter the machine has been installed, turn ON the power. The power switch is 
located on the rear of the right hand cabinet.
6-2 Adjustment Switches The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the play m\
eter.
2. Test Switch Slide the test switch ON to enter test mode. 
Test mode allows testing and the changing of game settings. (Refer to se\
ction
6-3 Test Mode  (page 12))
Service Bracket
COIN COUNTER
TEST SERVICE TEST SERVICE RIGHT PLAYER
LEFT PLAYER 
						

							Page 15
6-3 Test Mode
1. Open the coin door and slide the test switch ON. The menu screen will \
be displayed on the monitor.
2. Select the test required by leaning the bike left or right. The selected\
 test will blink
3. Enter the selected test by pressing the View Change push button. Selec\
t EXIT to return the Menu Screen.
4. After testing is completed, ensure that the test switch is returned to t\
he OFF position to return to normal game mode.
The T est Switch must always be in the OFF position for normal game mode.
MENU
COIN OPTIONS ------- (1) Sets the price of play  (See 6-3-1)
GAME OPTIONS ------- (2) Sets the game options  (See 6-3-2)
I/O TEST ------- (3) Used for testing switches and controls (See 6-3-3)
SOUND TEST ------- (4) Used for testing sound and setting volumes (See 6-3-4)
MONITOR TEST ------- (5) Used for adjusting the monitor 
ADS TEST ------- (6) Displays accumulated game data
OTHERS ------- (7) Used for testing the PC Boards and for initializing all of the settings
BANK : CHOOSE 
VIEW SW : ENTER 
						

							Page 16 6-3-1 Coin Options
1. Select item (1) COIN
OPTIONS on the
menu screen to set
the game cost and
related settings.
2. Lean the bike left or
right to select the
required item then
press View Change.
3. Use the Brake to
adjust the settings
UP or the Throttle to
adjust the settings
DOWN, standard
settings are displayed
in green.
4. Select EXIT and
press View Change
to return to the menu
screen.COIN OPTIONS
[ DEFAULT IN GREEN ]
GAME COST
1 COIN 1 CREDIT ------------------------ (a)
FREE PLAY NO ------------------------ (b)
EXIT
BANK :CHOOSE BRAKE :CHANGE+
VIEW SW :ENTER THROTTLE :CHANGE-
Note :- The price of play on this machine is set within the Cashflow Coin Mech.
Ensure that the Coin Options on the screen are set as shown in the following
table.
M E T IST N E T N O CTE S Y R O T C A F
t s o C e m a G ) a (9- 1 e l b a t t e s - - - - - - t i d e r c 1 r o f d e r i u q e r s n i o Ct i d e r C 1 n i o C 1
y a l P e e r F ) b (oN / s e YO N 
						

							Page 17 6-3-2 Game Options
1. Select item (1) COIN OPTIONS on the menu screen to set the game
options and related settings.
2. Lean the bike left or right to select the required item then press View
Change.
3. Use the Brake to adjust the settings UP or the Throttle to adjust the settings
DOWN, standard settings are displayed in green.
4. Select EXIT and press View Cange to return to the menu screen.
GAME OPTIONS
[ DEFAULT IN GREEN ]
GAME DIFFICULTY B --------------- (a)
GAME LAPS
GREEN HILL 3 --------------- (b)
NEO YOKOHAMA 2 --------------- (c)
ENTRY TIME B --------------- (d)
ID NUMBER 1 LINK ON 1 ------- (e), (f)
SEAT COLOUR RED --------------- (g)
LANGUAGE ENGLISH ------------- (h)
SOUND IN ATTRACT ON --------------- (i)
HI SCORE INITIALIZE NO --------------- (j)
EXIT
BANK :CHOOSE BRAKE :CHANGE+
VIEW SW :ENTER THROTTLE :CHANGE-
NOTES
•The game difficulty and number of laps and entry time must be set the
same on all positions that are linked.
•The ID number of the bike furthest left (when facing the front of the
machine) should be set to 1, and the other bikes set to 2, 3, or 4 in order
from left to right. The ID number of the farthest right position should
equal the number of bikes linked.
•Settings other than those described will cause the machine to operate
incorrectly. 
						

							Page 18
M E T INO I T P I R C S E DTE S Y R O T C A F
y t l u c i f f i D e m a G ) a ()d r a h ( C o t ) y s a e ( AB
l l i H n e e r G ) b (5- 2 t e s - - - e s r u o c l l i H n e e r G r o f s p a l f o r e b m u N3
a m a h o k o Y o e N ) c (5 - 1 t e s - - - e s r u o c a m a h o k o Y o e N r o f s p a l f o r e b m u N2
e m i T y r t n E ) d ()t s e t r o h s ( C o t ) t s e g n o l ( AB
r e b m u N D I ) e (r e b m u n e m a s e h t e v a h s e k i b d e k n i l o n t a h t o s t e S . s n o i t i s o p d e k n i l r o f y t i t n e d i e k i b s t e S
) f (
k n i L s y a l p s i D
n o i t a m r o f n Is t i n u d e k n i l f o r e b m u n + N O K N I L - w o h s l l i w y a l p s i D - d e k n i L e n i h c a M
F F O K N I L - w o h s l l i w y a l p s i D - e l b a C k n i L y t l u a F
1 N O - w o h s l l i w y a l p s i D - e n i h c a m e n o y l n O
G N - w o h s l l i w y a l p s i D - B C P k n i L y t l u a F
r u o l o C t a e S ) g (e s u n i e k i b f o r u o l o c e h t h c t a m o t t e S . r u o l o c e k i b e h t s t e S
e g a u g n a L ) h (en o N , h s i l g n E , l a u g n i l i Bh s i l g n E
t c a r t t A n i d n u o S ) i (ff O / n On O
e z i l a i t i n I e r o c S i H ) j (ff O / n Of f O
I/O TEST
DIP 4 12345678 ............................ (a)
LINK ON ............................ (b)
SWITCH TEST ............................ (c)
MOTOR TEST ............................ (d)
LAMP TEST ............................ (e)
EXIT
BANK :CHOOSE
VIEW SW :ENTER
6-3-3 I/O Test
1. Select item (3) I/O Test on the menu screen to test the switches or lamps.
2. Lean the bike left or right to select the required item then press View
Change.
3. Select EXIT and press View Change to return to the menu screen.
(a) Shows condition of DIP SW 4 on the PCB. In normal operation all switches
are OFF. (If a switch is ON it will be displayed in red).
Switch 1 if ON will force the PCB in to Test Mode.
Switch 8 if ON will freeze the picture on the monitor.
(b) Shows if the game is linked. 
						

							Page 19 6-3-3-1 Switch Test
1. Select Switch Test from the I/O Test menu. The following screen will
appear on the monitor.
LAMP TEST
ALL LAMPS
RED
YELLOW
BLUE
1
2
3
4
GREEN
VIEW-SW
VIEW-SW: EXIT
SWITCH TEST
TEST SW ON ................. (a)
COIN SW ON ................. (b)
SERVICE SW ON ................. (c)
BANK 00 CENTRE ................ (d)
THROTTLE 00 ................. (e)
BRAKE 00 ................. (f)
VIEW-SW ON................. (g)
BRAKE+THROTTLE: EXIT
2. The word ON will appear next to items a, b, c, and g each time the
respective switch is operated.
When the bike is pushed left, CENTRE will go off and OK appear just
before it reaches the extreme left, 00 will decrease. When the bike is
pushed right, CENTRE will go off and OK appear just before it reaches
the extreme right, 00 will increase.
When the THROTTLE or BRAKE are operated, OK will appear just
before they are fully on, and 00 will increase.
3. Operate the brake and throttle together to exit and return to the I/O Test
menu screen.
6-3-3-3 Lamp Test
1. Select Lamp Test from the I/O Test  menu. The following screen will
appear on the monitor 6-3-3-2 Motor Test
This test is not used on this machine 
						

							Page 20 2. The lamps will automatically illuminate in turn as indicated on the screen.
3. Press View Change to return to the I/O Test menu screen.
SOUND TEST
[ DEFAULT IN GREEN ]
VOLUME FRONT LEFT SP. 55 ------------------- (a)
FRONT RIGHT SP. 55 ------------------- (b)
TANK SP. 50 ------------------- (c)
REQUEST SONG No. 000 ------------------- (d)
MESSAGE ETC. ------------------- (e)
EXIT
BANK :CHOOSE BRAKE :CHANGE+
VIEW SW :ENT/ON,OFF THROTTLE :CHANGE- 6-3-4 Sound Test
1. Select item (4) Sound Test on the menu screen to test the sound and
speakers.
2. The following screen will appear on the monitor.
3. Select the required item by leaning the bike left or right. The selected item
will blink.
4. Operating the brake will increase the value setting and operating the throttle
will decrease the value setting. Standard values are displayed in green.
5. Press View Change to start or stop a Reqest Song No. sound. (Request
Song No. 3 will generate a stereo sound test.
6. Select EXIT and press View Change to return to the menu screen.
m e t Ino i t p i r c s e Dyr o t c a F
t e S
at s e d u o L 3 6 - t s e t e i u Q 0 0 - - - - - - e m u l o v r e k a e p s t f e l t e S2 3
bt s e d u o L 3 6 - t s e t e i u Q 0 0 - - - - - - e m u l o v r e k a e p s t h g i r t e S2 3
ct s e d u o L 3 6 - t s e t e i u Q 0 0 - - - - - - e m u l o v r e k a e p s k n a t e k i b t e S2 3
d0 0 0 . d n u o s t n e r e f f i d a e c u d o r p l l i w r e b m u n h c a E . g n i t s e t r o f d n u o s t c e l e S
. t s e t o e r e t s a e t a r e n e g l l i w- - -
eem a n g n o s s y a l p s i D- - - 
						

							Page 21 6-3-5 Monitor Test
1. Select item (5) Monitor Test on the menu screen to set up and adjust the
monitor.
2. On entering monitor test, the following screen will appear on the monitor.
3. Lean the bike to select a test and press View Change to enter the test and
to return to Monitor Menu from a test.
6-3-6 ADS Data
1. Select item (5) ADS Data on the menu screen to view machine history
details.
2. The following screen will appear on the monitor.
ADS
POWER ON 000000 .................. (a)
PLAY TIME 000000 .................. (b)
PLAY TIME AVE 000000 .................. (c)
PLAY NUMBER 0000 .................. (d)
COURSE-VIEW .................. (e)
COURSE-BIKE .................. (f)
COURSE -LINK .................. (g)
COURSE-C. P. .................. (h)
COURSE-P.T. ................... (i)
INITIALIZE ................... (j)
EXIT
BANK :CHOOSE
VIEW-SW:ENTER
MONITOR
GRADATION PATTERN
CROSSHATCH GREEN
CROSSHATCHWHITE
WHITE WINDOW (H)
WHITE WINDOW (M)
WHITE WINDOW (L)
INTERLACE PATTERN
VIEW ANGLE ADJUST (CRT)
VIEW ANGLE ADJUST (PROJECTOR)
FULL WHITE
EXIT
BANK :CHOOSE
VIEW-SW:ENTER