Namco Alpine Racer 2 Operators Manual

Page 12 GAME SELECTION
• Skier Selection
After inserting sufficient credit, the Skier Selection Mode will be displayed. The
player selects one of three skiers, Basic, Mogul or Downhill by using the L/R
select buttons and pressing the decision (Viewpoint) button
• Game Mode Selection
After the Skier Mode has been selected, the Game Mode Selection screen is
displayed. The player selects either the Race Mode or Time-Trial Mode by
using the L/R selection buttons, and pressing the decision (Viewpoint)...

Page 13 • Single Time-Trial Mode
The object of the game is to pass between the flags (gates) in the fastest time.
The game is over when the player crosses the finish line within the given time
period, or the time period reaches zero. The time period is increased by one
second each time a player passes through a gate.
• Linked Time Trial Mode
The game is over when the player crosses the finish line within the given time
period, or the time period reaches zero. The time period is increased by one
second...

Page 14
3. MAJOR COMPONENTS 

Page 15
4. MOVING THE MACHINE
WARNING • This machine is fitted with castors to make it easier to move.Take care when moving the machine on an inclined surface.
• The Header Assembly has a forward centre of gravity, so it is important that at least 
two people are used to fit or remove
the Header Assembly.
• The fitting position of the Header Assembly is high, and it is important that a means of reaching the height safely, without 
stretching, is available. (e.g. steps, step stool etc.)
• The overall...

Page 16 

Page 17
WARNING
This machine is designed for Indoor Use Only
Do Not install the machine in the following places.
1. Outdoors
2. Direct sunlight, places with excessive humidity or dust,
places where there is water leakage, near
air-conditioning or heating equipment, places with
excessive heat or cold temperature.
3. Places where it would be in the way of emergency exits
or fire extinguishing equipment.4. Unstable places or places with excessive vibration.
5. Places that are not level. 

Page 18
5-1 Assembling the Machine
1. Remove 4off Security Screws (M5x16) and remove the Clamp Bracket Vac-Form
from the front of the monitor cabinet.
2. Remove the 4off Hex Head Screws (M10x20), Spring Washers and Flat
Washers.
Note: Do not loose the Vac-Form or screws as they are needed for refitting.
3. Remove 4off Hex Head Screws (M10x20), Spring Washers and Flat Washers
and remove the Ski Pole Clamp Bracket from the Shipping Bracket.
Note: Do not loose the Bracket or screws as they are needed for...

Page 19
NOTE:-
When the machine is fully assembled and in its final position, lower the 8 level
adjusters, with a spanner, so that all castors are raised from the floor by
approximately 5mm, and the machine is level. Tighten the lock nuts with a
spanner to ensure that the level adjusters do not move.
If this machine is installed on a smooth or shiny floor, it is recommended that rubber
slip mats be placed under each adjustable foot to prevent the machine from moving
when being played. 6. Refit the Clamp...

Page 20
5-2 Fitting the Header Assembly
The Header Assembly has a forward centre of gravity, so it is important that at
least 
two people are used to fit or remove the Header Assembly.
The fitting position of the Header Assembly is high and it is important that a means of
reaching the height safely, without stretching, is available. (e.g. steps, step stools etc)
1. Remove the two security screws
(M5x12) and remove the
Connector Cover.
2. Place the Header Assembly on to the monitor cabinet, slide
the...

Page 21
Service Bracket
COIN COUNTER
TEST SERVICE TEST SERVICERIGHT PLAYER
LEFT PLAYER
6. ADJUSTMENTS
6-1 Turning on the Power
After the machine has been installed, turn ON the power. The power switch is 
located on the rear of the monitor cabinet.
6-2 Adjustment Switches The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the play m\
eter.
2. Test Switch Slide the test switch ON to enter test mode. 
Test mode allows...