Namco Ace Driver Deluxe Installation Commissioning Manual

Page 1-4 Removing the Shipping Brackets
NOTE: Store the removed shipping brackets in a safe place as they must be refitted
when replacing the drive castor, when shipping, or when moving the machine.
1) Remove  two hex head bolts (M8x20) from each rear shipping bracket, and
remove the brackets. Retain the four hex head bolts (M8x20) that were used to fit
the shipping bracket for future use.
2) Slacken two security screws (M10x30), and remove two heax head bolts (M8x20)
from each front shipping bracket,...

Page After removing the shipping brackets, install the supplied safety rubber skirt (D) and
skirt stay (F) to the upper base assembly as described below.
NOTE: The safety rubber skirt is to prevent hands or feet being trapped by the
moving parts. Be sure to install the safety rubber skirts.
1) The safety rubber is installed on the outside of each seat assembly. i.e.on the left
of the left hand seat and on the right of the right hand seat.
2) Install the safety rubber and skirt stay using three security...

Page 1-5 Installing the Guard Fence
1) Fasten the guard fence with two retaining plates and security screws (M8x20),
flat washers, and security washers.
2) Fit the extension brackets (R),(L) to the seat base using six security screws
(M8x20), spring washers, and flat washers on each. Ensure that the angles of the
extension bracket match the angles of the extensions fitted to the seat bed.
8 

Page
1-6 Applying the Number Stickers
Apply the racing number stickers to the seats and sign boards as shown b\
elow. 
The team colours and car numbers should match those shown in the followi\
ng table. 
[NOTE]: Ensure that the numbers on the screen match the sticker numbers. The TEAM COLOURS can be checked in the Test Mode - Setting the 
Game Options.  (page 14)
TEAM COLOURRED 25BLUE 3YELLOW 17GREEN 11R
Team ColourRedBlueYellowGreen
Car Number2531711
9 

Page
1-7 Linking Two or More Machines.
Up to four machines (8 seats) can be linked together. 
The machines should be linked as described below.
NOTE:Each machine can draw up to 8 amps. Make sure that the power supply
is adequate.
1) Ensure that the 
power is
“OFF”.
2) Loosen the two screws 
(M4x10) on
the back of
the tower
assy, and
remove the
connector
cover.
3) Set the link switches to “ON” , “EXT”, and “ON”. (See Diag.)
4) Use the supplied link cable and connect the machines between “IN”
and “OUT”...

Page
1-7-1 Setting the Link Switches
The link switches are used to set the connection between seats and machines.
1). Setting only one machine (2 seats)
Set the link switches to “ON”, “INT”, and “ON”.
Note: Do not use a link cable.
2) Setting two or more machines.
Set the link switches to “ON”, “EXT”, and “ON”.
3) Install the connector cover using
the two screws (M4x10).
The link procedure is now complete.
4) Setting for faulty PCB.
If the game PCB of only one side is faulty, set the link on that side to...

Page
2 ADJUSTMENTS
2-1 Turning on the PowerAfter the machine has been correctley installed, turn ON the power. 
The Power switch is located next to the IEC power inlet socket on the re\
ar of the
tower unit
2-2 Adjustment Switches The adjustment switches are located inside the coin door. 
1. Service Switch Press this switch to obtain game credits without incrementing the play m\
eters.
2. Test Switch Slide this switch “ON” to enter test mode. 
Test mode allows game testing and the changing of game...

Page
2-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Sc\
reen” will be displayed on the monitor.
2. Select the test required by moving the shift lever up or down. The colou\
r of the selected test will change.
3. Enter the selected test by stepping on the accelerator. Select “EXIT”\
 to return to the “Menu Screen” (step on the accelerator when using the moni\
tor test 
screen).
4. After testing is completed, ensure that the test switch is returned to t\
he “OFF” position to...

Page 2-3-1 Coin Options
a. Select item (1)
“COIN OPTIONS”
on the menu screen,
to set the game cost
and related settings.
b. Use the shift lever to
select the required
item then step on
the accelerator.
c. Use the shift lever to
change the settings
then step on the
accelerator to store
the new values.
d. Select “EXIT” to
return to the menu
screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the
Coin Options on the screen are set as shown in the following...

Page 2-3-2 Game  Options
a. Select item (2) “GAME
OPTIONS” on the
menu screen to set the
game options.
b. Use the shift lever to
select the required
item then step on the
accelerator.
c. Use the shift lever to
change the settings
then step on the
accelerator to store the
new values.
d. Select “EXIT” to return
to the menu screen.
Note:  Race Class (c) must
be set first before
changing items (d),
(e), or (f).
GAME OPTIONS [DEFAULT IN GREEN]
PCB ID NUMBER ................. (a)
TEAM COLOUR BLUE 3...