Namco Ace Driver Deluxe Installation Commissioning Manual

Page
M E T INO I T P I R C S E DTE S Y R O T C A F
r e b m u N B C P ) a (e m a s e h t e v a h s n o i t i s o p d e k n i l e h t f o e n o n t a h t o s t e s e b d l u o h s r e b m u n B C P e h T
r e b m u n
r u o l o C m a e T ) b (DE R62 r o 5 2
E U L B4r o 3
W O L L E Y81 r o 7 1
N E E R G21 r o 1 1
e b d l u o h s s r e b m u n e c a r t n e r e f f i d , d e k n i l e r a ) s t a e s 6 ( s t e s e e r h t n a h t e r o m n e h W *
. s r u o l o c m a e t e m a s e h t r o f d e s u
e c a R ) c...

Page
2-3-3 I/O Test
1. Select item (3) “I/O TEST” on the menu screen. 
2. Use the shift lever to select the required item then step on the acceler\
ator.
I/O TEST
DIP 2 12345678 .......... (a) Option Switch (CPU-PCB Sw2) 3 12345678 .......... (b) Option Switch (CPU-PCB Sw1)
LINK ON 2 COUNT 0 .......... (c) Link Check
SWITCH .......... (d) Switch Test 
MOTOR .......... (e) Motor Test
LAMP .......... (f) Lamp Test
LED .......... (g) LED Test
EXIT 
GAS: ENTER SHIFT: CHOOSE
(a) Displays the state of the...

Page 2-3-4 Switch Test
The following screen is displayed when “SWITCH” is selected on the I/O screen.
I/O TEST
DIP 2 12345678
3 12345678
LINK ON 2 COUNT 0
SWITCH
(a) Accelerator ..................... GAS: *0000 COIN 1: OFF ........ (e) Coin 1 switch
(b) Brake ..................... BRAKE *0000 COIN 2: OFF ........ (f)  Coin 2 switch
(c) Steering ..................... STEER *0000 SERVICE: OFF ........ (g) Service switch
(d) Shift ..................... SHIFT CENTRE VIEW: OFF ........ (h) View change switch...

Page
2-3-5 Motor Test
The following screen is displayed when “MOTOR” is selected on the \
I/O screen.
I/O TEST 
DIP 2 12345678 3 12345678
LINK ON 2 COUNT O
SWITCH 
MOTOR BASE MOTOR OFF ............... (a) Seat motor test
STEERING OFF TORQUE  00 ............... (b) Steering motor test
EXIT
GAS: TURN SHIFT: CHOOSE
(a) Tests the seat roller motor. When “BASE MOTOR” is selected and the accelerator is pressed the t\
est is “ON” 
and the motor starts to operate. Pressing the accelerator again turns th\
e test...

Page 2-3-7 Lamp Test
The following screen is displayed when “LAMP” is selected on the I/O screen.
I/O TEST
DIP 2 12345678
3 12345678
LINK ON 2 COUNT 0
LAMP
TOP LAMP ........................ (a)
SIGNAL LAMP RED ........................ (b)
SIGNAL LAMP GREEN ........................ (c)
EXIT
GAS: LIGHT SHIFT: CHOOSE
(a) Tests the top lamp.
(b) Tests the red signal lamp.
(c) Tests the green signal lamp.
Select “EXIT” to return to the I/O test screen.
2-3-8 LED Test
The following screen appears when “LED” is...

Page 2-3-9 Sound Test
To adjust the sound volume, select “SOUND TEST” in the menu screen. The
following screen will be displayed.
SOUND TEST [DEFAULT IN GREEN]
VOLUME [MAX 63]
LEFT RIGHT
(a) Left speaker volume ................. 40 40 ........ (b) Right speaker volume
SONG 40
EXIT
GAS: ENTER SHIFT: CHOOSE
Select (a) or (b) by using the shift lever, the characters will blink in red, when the
accelerator is pressed the numbers will start to blink. Moving the shift lever up will
increase the number, moving...

Page 2-4 Adjustments When Replacing Parts (Initialization)
The following adjustments should always be performed after initial installation and
after replacing the game PC board, ROM, Steering Assy, Pedal Assy, or Control Pots.
The game will not operate correctly if these adjustments are not made.
a) Ensure that accelerator and brake pedals are fully returned.
b) Place the steering wheel to it’s centre position and remove hands from the wheel
(
The steering wheel does not return to centre by itself.)
c)...

Page23
3. DISASSEMBLY
NOTE: The proper number of people (listed in each item) should be used when
disassembling.
This machine may be disassembled further than as shipped for shipping and moving.
The following is a general method of disassembly.
NOTE: Parts may be damaged if placed upside down or on their side when removed. 

Page
24 3-1. Removing the Monitor Assy (L), (R)
DANGER: There are areas within the monitor that have high temperature and very
high voltage even after the power has been removed. Extreme care
must be taken to avoid burns or electric shock.
DANGER: The monitor weighs approx 60kg, at least two people should be used to
remove the monitors.
1) Ensure that the power is turned OFF before removing the monitors.
2) Remove the back door from the monitor.
3) Disconnect the six way video connector and three way...

Page
25 3-2 Disassembling the Upper Seat Assy from the Seat Base Assy
WARNING: The weight of the upper seat assembly is approx. 120kg. Foot
position is poor and the assembly heavy, so at least five people
should be used for disassembly
WARNING: This work involves moving the seat assembly from left to right in
order to remove screws. Take care not to trap or injure the other
person when performing this work.
1) Remove the rear covers (L), (R).
Removing the Rear Cover (L)
1) Remove the rear guard fence.
2)...