Multi-Tech Systems Mvp110 Standalone Voice/ip Geteway Quick Start Guide

41 Configuring MultiVOIP Slaves
disconnected. Jitter is the inter-arrival packet deviation
(phase shift of digital pulses) over the transmission
medium that causes voice breakup which can be
particularly disruptive to voice communications. The
default setting is 20 milliseconds. A higher value means
that the voice transmission will be more accepting of jitter.
A lower value will be less tolerant of jitter.
Consecutive Packets Lost defines the number of
consecutive packets that are lost after which the...

MultiVOIP Quick Start Guide
42The Minimum Jitter Value default setting is 150
milliseconds, the Maximum Jitter Value default setting is
300 milliseconds, and the Optimization Factor default
setting is 7.
If your country/region is not the default USA, click the
Regional tab and proceed to step 17.
16. To change the Tone Pairs on the Regional tab, click the
Country/Region down arrow and highlight your specific
country or region.
Note: If your country or region is not listed, click Custom
to define it.
The...

43 Configuring MultiVOIP Slaves
Proprietary Phonebook option is enabled and in the
Database Type group, select the Slave option. The
Master IP Address box becomes active.
Note: After you have enabled the Slave option, the Slave
Status button is replaced by the Update button. Once
your Phone Directory database has been created, you can
click this button to refresh the entries in the Phone
Directory Database window.
18. Enter the IP address (204.022.122.118) of the New York
Office MVP110 in the Master IP...

MultiVOIP Quick Start Guide
4420. Click Download Setup to write the new configuration to
the slave unit. The Save Setup dialog box displays.
21. Select  the Save Current Setup as User Default
Configuration check box and click OK. The setup
configuration is written to the MVP110.  After the setup is
written to the MVP110, it reboots.
22. Check that the Boot LED on the MVP110 is off after the
download is complete. This may take several minutes as
the MVP110 reboots.
23. You are returned to the Main menu....

45 Configuring MultiVOIP Slaves
Deploying the VOIP Network
For a Proprietary Phone Directory database, the VOIP
administrator can deploy the pre-configured slave MVP110s to
their remote sites. The remote site administrators need only
connect power to the pre-configured MVP110, connect the
MVP110 to their Ethernet LAN and predefined telephone
equipment, and then wait for the phone directory database to
be downloaded.
With the Gatekeeper option enabled on the Phone Directory
Database dialog box, all MVP...

MultiVOIP Quick Start Guide
46








   	
  !	#
      

Figure 5.  Remote Site Cable Connection
3. Connect a network cable to the ETHERNET (RJ-45)
connector on the back of your MVP110.
4. If you are connecting a station device such as an analog
telephone, fax machine, or Key Telephone System (KTS)
to your MVP110, connect a phone cable from the phone
connector on the MVP110 to the Phone connector on the
back of the MVP 110 and...

47 Deploying the VOIP Network
Limited Warranty
Multi-Tech Systems, Inc. (“MTS”) warrants that its products will
be free from defects in material or workmanship for a period of
two years from the date of purchase, or if proof of purchase is
not provided, two years from date of shipment. MTS MAKES
NO OTHER WARRANTY, EXPRESSED OR IMPLIED, AND
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS  FOR A  PARTICULAR  PURPOSE ARE  HEREBY
DISCLAIMED. This warranty does not apply to any products
which have been...

MultiVOIP Quick Start Guide
48
Technical Support
Multi-Tech Systems has an excellent staff of technical support
personnel available to help you get the most out of your Multi-
Tech product. If you have any questions about the operation of
this unit, or experience difficulty during installation you can
contact Tech Support via the following:
Phone:
(800) 972-2439 (USA and Canada)
(763) 785-3500 (international and local)
Internet:
http://www.multitech.com
Please have your product information available,...

49 Warranty and Regulatory Information
FCC Declaration
NOTE: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful...

82050950