Home > Multi-Tech Systems > Communications System > Multi-Tech Systems Mvp110 Standalone Voice/ip Geteway Quick Start Guide

Multi-Tech Systems Mvp110 Standalone Voice/ip Geteway Quick Start Guide

Here you can view all the pages of manual Multi-Tech Systems Mvp110 Standalone Voice/ip Geteway Quick Start Guide. The Multi-Tech Systems manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 1


	


Standalone Voice/IP Gateway
Model MVP110
H.323 Mode
Quick Start Guide 

Page 2

Quick Start Guide
82050950 Revision A
MultiVOIP 100 (Model MVP110)
This publication may not be reproduced, in whole or in part, without prior
expressed written permission from Multi-Tech Systems, Inc.   All rights
reserved.
Copyright © 2001, by Multi-Tech Systems, Inc.
Multi-Tech Systems, Inc. makes no representations or warranties with
respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose.
Furthermore, Multi-Tech...

Page 3

iii
Contents
Introduction ................................................................................... 4
Related Documentation ................................................................. 5
Installing Your MVP110 ................................................................. 6
Installing and Configuring Your MVP110 ................................. 6
Deploying the VOIP Network .................................................. 7
Unpacking Your MultiVOIP...

Page 4

MultiVOIP Quick Start Guide
4
Introduction
Welcome to Multi-Techs stand-alone Voice/IP Gateway, the
MultiVOIP model MVP110. The MVP110 allows analog voice
and fax communication over an IP network. Multi-Tech’s voice/
fax gateway technology allows voice/fax communication to be
transmitted, with no additional expense, over your existing IP
network, which has traditionally been data-only. To access this
free voice and fax communication, all you have to do is
connect the MVP110 to your telephone equipment,...

Page 5

5 Introduction
The MVP110 has one FXS voice/fax channel, a 10 Mbps
Ethernet LAN interface, and a Command port for configuration.
System management is provided through the Command port
using bundled Windows
® software which provides easy-to-use
configuration menus and comprehensive online Help.
Related Documentation
The MVP110 Quick Start Guide is intended to be used by
qualified systems administrators and network managers. This
Quick Start Guide provides the necessary information for a
qualified person...

Page 6

MultiVOIP Quick Start Guide
6
Installing Your MVP110
The basic steps of installing your MVP110 network involve
unpacking the units, connecting the cables, and configuring
the units using management software (MVP 110
Configuration). This  process results in a fully functional Voice
Over IP network. A brief description is provided below with
detailed instructions provided later.
Installing and Configuring Your MVP110
The VOIP administrator must first install the MVP110 software
and then configure each...

Page 7

7 Introduction
Once all Slave units are configured, the process moves on to
the “Deploying the VOIP Network” section.
Deploying the VOIP Network
The final phase of the installation is deployment of the
network. When the remote MultiVOIPs are sent to their remote
sites, the remote site administrators need only connect the
units to their LAN and telephone equipment. A full Phone
Directory Database Proprietary Phonebook, supplied by the
Master MultiVOIP will be loaded into their units within minutes
of...

Page 8

MultiVOIP Quick Start Guide
8
Unpacking Your MultiVOIP
Remove all items from the box. (See Figure 2.)










	

	




Figure 2. Unpacking
Safety Warnings
Caution: Danger of explosion if battery is incorrectly replaced.
A lithium battery on the circuit board provides backup power
for the time keeping capability. The battery has an estimated
life expectancy of ten years.
When the battery starts to weaken, the date and time may be
incorrect. If...

Page 9

9 Cabling
Cabling Your MultiVOIP
Cabling your MultiVOIP involves making the proper Power,
Command Port, and Ethernet connections. Figure 6 shows the
back panel connectors and the associated cable connections.
The Cabling Procedure section provides step-by-step
instructions for cabling your MultiVOIP.
Cabling Procedure
1. Using the supplied cable, connect the power supply to a
live AC outlet, then plug the power supply into the MVP
110 as shown in Figure 3.





...

Page 10

MultiVOIP Quick Start Guide
10to your MVP 110, connect an RJ-11cable  to the Voice/Fax
Channel  connector on the back of the MVP 110 and the
other end to the station device.
5. Turn on power to the MVP 110 by setting the power switch
on the right side to the On position. Wait for the Boot LED
on the MVP 110 to go off before proceeding. This may
take a couple of minutes. 
Start reading Multi-Tech Systems Mvp110 Standalone Voice/ip Geteway Quick Start Guide

Related Manuals for Multi-Tech Systems Mvp110 Standalone Voice/ip Geteway Quick Start Guide

All Multi-Tech Systems manuals