Multi-Tech Systems Multivoip 200 Model Mvp200 Standalone Voice/ip Gateway Quick Start Guide

21 Configure Master MultiVOIP
If you changed the voice coder, ensure that the same
voice coder is used on the voice/fax channel you are
calling; otherwise, you will always get a busy signal.
17 If you selected the FXO interface and are using touchtone
dialing, you can set up the DTMF gain (or output level in
decibels - dB) for the higher and lower frequency groups
of the DTMF tone pair. Make your selections in the drop-
down lists in the DTMF Gain group.
Note: Only change the DTMF gain under the...

MultiVOIP Quick Start Guide
2219 You can set up billing options for inbound and/or outbound
calls by checking them in the Billing Options group and
then typing in the charge in cents per x seconds.
20 Password protection can be enabled for outbound and/or
inbound calls on the selected voice/fax channel. If you
enable password Authentication on inbound or outbound
calls, you need to also enter a password of up to 14
numeric characters in the Password field.
21 The Automatic Disconnect option limits call...

23 Configure Master MultiVOIP
The Tone Pairs group parameters change per your
choice.  Click OK when finished. Proceed to step 23 to
begin building your phone directory database.
23 The Phone Directory Database dialog box is displayed.
You will build your personalized MultiVOIP Phone
Directory in the following steps.
The MultiVOIP configured as a “Master” will contain the
master database. The master database has the phone
numbers of all the MultiVOIP’s available for
communication on an IP network. This...

MultiVOIP Quick Start Guide
2424 The Add/Edit Phone Entry dialog is displayed.
In the Station Information group, enter the unique phone
number of the local device connected to Channel 1 in the
Phone Number field (for example phone number 101).
25 The Description field is optional, but can be useful in
associating the channel to the extension. If you wish, enter
a description of your local phone number. This description
serves to identify the phone number you entered in the
previous step (for example,...

25 Configure Master MultiVOIP
27 In the MultiVOIP Identification group, enter the IP
address of the Master MultiVOIP in the IP Address field.
For example, 204.22.122.118. Then obtain the 12-digit
Node ID# (0008005xxxxx) from the ID plate on the back
panel of the MultiVOIP and  enter this number in the
Ethernet Node ID field. If the ID plate is missing or
damaged, you can also Telnet to the MultiVOIP and, on
the MultiVOIP Telnet Server menu enter 1 to advance to
the Main Menu, then enter 3 for System...

MultiVOIP Quick Start Guide
2628 Click OK and you are returned to the Phone Directory
Database dialog box, which now includes phone number
101 with its IP address, channel number and description.
29 Click Add (+) and the Add/Edit Phone Entry dialog box is
displayed again.
30 Enter the phone number for the remote MultiVOIP in the
Station Information group Phone Number field. For
example, 201.
31 Click the Description field and enter a description for the
remote MultiVOIP phone number for Channel 1. For...

27 Configure Master MultiVOIP
32 Enter the IP address of the remote MultiVOIP in the IP
Address field in the MultiVOIP Identification group. For
example, 202.56.39.100.
33 Click OK and you are returned to the Phone Directory
Database dialog box, which now includes the second
number and related information in the Phone Number list.
Note: If only Channel 1 is active, you must enter two
phone numbers. The first number will be the local
MultiVOIP phone number for Channel 1, and the second
number will be the...

MultiVOIP Quick Start Guide
28If both Channels 1 and 2 are active, four phone numbers
will have to entered.
34 When you have finished, click OK to download the setup
configuration to the MultiVOIP.
35 The Checking MultiVOIP dialog box is displayed.
Click OK to proceed.
36 The Writing Setup dialog box is displayed as the setup
configuration is written to the MultiVOIP.   

29 Configure Master MultiVOIP
37 After the setup is written to the MultiVOIP, the unit is
rebooted.
38 Check to ensure that the BOOT LED on the MultiVOIP is
Off after the download is complete. This may take
several minutes as the MultiVOIP reboots.
39Win3.1 users - you are returned to your Program
Manager where the MultiVOIP Program Group and
Program Items (Windows icons) are displayed.
Win95/98/NT users - you are returned to your
MultiVOIP folder which is open and visible on your
desktop.
At this time,...

MultiVOIP Quick Start Guide
30
Phase 2: Configure Your Slave MultiVOIPs
If you are installing a MultiVOIP behind a firewall, you need to
add the following UDP ports to your firewall.
Q.931 Signaling, Ch1 [900] Q.931 Signaling, Ch2 [902]
Status [5000]
Ch1 RTP [5004] Ch1 RTCP [5005]
Ch2 RTP [5006] Ch2 RTCP [5007]
Refer to your firewall user documentation to enter and open
these ports.
1 Disconnect the PC from the command port of the Master
MultiVOIP and connect it to the command port on the
Slave...