MSI Click Bios 2 Manual

 Important
●The M2_1 slot will only run PCIe 3.0 x2 speed whenM2_1 slot is installed with a M.2 PCIe device andPCI_E4 slot is installed with a PCIe x1 device at thesame time.
●Intel® RST only supports PCIe M.2 SSD with UEFI
ROM, does not support Legacy ROM.
Installing M.2 module
M2_1~2: M.2 Slots
1
2
330°
3.
Tighten the base screw
into the hole of the
distance to the M.2 slot
as the length your M.2
module.
4.
Insert your M.2 module
into the M.2 slot at a
30-degree angle.
5.
Put the screw in the
notch on...

M.2/ SATA & SATAe combination table
SlotAvailable SATA/ SATAe connectors
M2_1 Empty SATA PCIe PCIe SATA Empty PCIe SATA M2_2 PCIe PCIe PCIe SATA SATA SATA Empty Empty
SATA_EX1 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
SATA_EX2 ✓ ─ ─ ─ ─ ✓ ─ ─
SATA1 ✓ ✓ ✓ ─ ─ ─ ✓ ✓
SATA2 ✓ ✓ ✓ ─ ─ ─ ✓ ✓
SATA3 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
SATA4 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓
SATA5 ✓ ─ ─ ─ ─ ✓ ─ ─
SATA6 ✓ ─ ─ ─ ─ ✓ ─ ─
(SATA: M.2 SATA SSD,  PCIe: M.2 PCIe SSD, ✓: available, ─: unavailable)
M.2 slots with examples of various combination possibilities
PCIe
PCIe PCIe
SATASATA2...

SATASATA
SATA5
SATA6
1xM.2 SATA SSD + 2xSATAe HDDs
1xM.2 SATA SSD + 1xSATAe HDD +
2xSATA HDDs
SATA_EX1
SATA_EX1 SATA_EX2
SATA SATA
SATA SATA
2xM.2 SATA SSDs + 2xSATA HDDs
2xM.2 SATA SSDs + 1xSATAe HDD
SATA_EX1
SATA_EX1
SATA_EX1
SATA3
SATA4
PCIe
PCIe PCIe PCIe
PCIe
SATA SATAPCIeSATA2
SATA2
SATA2 SATA2SATA1
SATA1
SATA1 SATA1
SATA3
SATA3 SATA4
SATA4
2xM.2 PCIe SSDs + 4xSATA HDDs
1xM.2 SATA SSD + 1xM.2 PCIe SSD + 
4xSATA HDDs 1xM.2 SATA SSD + 1xM.2 PCIe SSD + 
2xSATA HDDs + 1xSATAe HDD 2xM.2 PCIe SSDs +...

OC1: GAME BOOST Knob 
This knob allows you to manually select a stage from number 0 (default)\
 to number 
11 (extreme) for overclocking your CPU. The CPU’s voltage and frequ\
ency will be 
automatically adjusted after you power on your computer.
0  1  2  4  6  8   1011
Using GAME BOOST Knob
To setup the GAME BOOST knob, take the following steps:
1.
Make sure the GAME BOOST is controlled by hardware. There are two GAME
BOOST LED indicators next to the GAME BOOST Knob. The red LED indicates
the GAME BOOST...

POWER1, RESET1: Power Button, Reset Button
The Power / Reset button allows you to power on / reset the computer.
Power button
Reset
Reset button
JPWR1~2: Power Connectors
These connectors allow you to connect an ATX power supply. 
24
131
12
JPWR1 1
+3.3V 13+3.3V
2 +3.3V 14-12V
3 Ground 15Ground
4 +5V 16PS-ON#
5 Ground 17Ground
6 +5V 18Ground
7 Ground 19Ground
8 PWR OK 20Res
9 5VSB 21+5V
10 +12V 22+5V
11 +12V 23+5V
12 +3.3V 24Ground
5
4 1
8
JPWR2
1 Ground 5+12V
2 Ground 6+12V
3 Ground 7+12V
4 Ground...

JFP1, JFP2: Front Panel Connectors
These connectors connect to the switches and LEDs on the front panel.
1 2 109
JFP1
1 HDD LED + 2 Power LED +
3 HDD LED - 4 Power LED -
5 Reset Switch 6 Power Switch
7 Reset Switch 8 Power Switch
9 Reserved 10No Pin
JUSB3~4: USB 3.1 Gen1 Connectors
These connectors allow you to connect USB 3.1 Gen1 ports on the front pa\
nel.
1
10 11
20
1 Power 11USB2.0+
2 USB3_RX_DN 12 USB2.0-
3 USB3_RX_DP 13 Ground
4 Ground 14 USB3_TX_C_DP
5 USB3_TX_C_DN 15 USB3_TX_C_DN
6 USB3_TX_C_DP...

JAUD1: Front Audio Connector
This connector allows you to connect audio jacks on the front panel.
1 2 109
1 MIC L 2Ground
3 MIC R 4NC
5 Head Phone R 6 MIC Detection
7 SENSE_SEND 8 No Pin
9 Head Phone L 10 Head Phone Detection
Charger Port
The JUSB4  (red mark) connector is a charger port which can increase 
USB power output for fast charging your smartphone or USB-powered 
devices. The Charger Port is hardware controlled by motherboard 
chip, it can still charge your device in suspend, hibernate state or...

12
14
13
1 LPC Clock 2 3V Standby power
3 LPC Reset 4 3.3V Power
5 LPC address & data pin0 6 Serial IRQ
7 LPC address & data pin1 8 5V Power
9 LPC address & data pin2 10 No Pin
11 LPC address & data pin3 12 Ground
13 LPC Frame 14 Ground
JTPM1: TPM Module Connector
This connector is for TPM (Trusted Platform Module). Please refer to t\
he TPM security 
platform manual for more details and usages.
JUSB1~2: USB 2.0 Connectors
These connectors allow you to connect USB 2.0 ports on the front panel.
1 2 10
9
1...

CPUFAN1~2, SYSFAN1~3: Fan Connectors
Fan connectors can be classified as PWM (Pulse Width Modulation) Mode \
and 
Voltage Mode. PWM Mode fan connectors provide constant 12V output and ad\
just fan 
speed with speed control signal. Voltage Mode fan connectors control fan\
 speed by 
changing voltage. Therefore, when you plug a 3-pin (Non-PWM) fan to a \
PWM Mode 
fan connector, the fan speed will be always maintained at 100%, and that\
 could be 
noisy.
1
CPUFAN1/ CPUFAN2
1 Ground 2+12V
3 Sense 4 Speed...

JCI1: Chassis Intrusion Connector
This connector allows you to connect the chassis intrusion switch cable.\
 
Normal
(default)Trigger the chassis 
intrusion event
Using chassis intrusion detector
1.Connect the JCI1 connector to the chassis intrusion switch/ sensor on the
chassis.
2.
Close the chassis cover.
3.
Go to BIOS > Settings > Security > Chassis Intrusion Configuration .
4.
Set Chassis Intrusion to 

Enabled.
5.
Press F10 to save and exit and then press the  Enter

 key to select Yes.
6.
Once the...