MSI C 770-c45 Manual

							
2
MS-7599

Led Status indicators (optional)
Blue lightoff
Led   Led2   Led   Led4 Mode
                                CPu is in  phase power mode.
                                 CPu is in 4 phase power mode.  
						

							
22

BioS SetuP
Power  on  the  computer  and  the  system  will  start  PoSt  (Power on  Self test) 
process.  When  the  message  below  appears  on  the  screen,  press    key  to 
enter Setup.
Press deL to enter SetuP
if the message disappears before you respond and you still wish to enter Setup, 
restart  the  system  by  turning  it  oFF  and on  or  pressing  the  ReSet  button.  you 
may  also  restart  the  system  by  simultaneously  pressing  ,  ,  and   keys.
Main Page
Standard CMoS Features
use this menu for basic system configurations, such as time, date etc.
advanced BioS Features
use this menu to setup the items of special enhanced features.
integrated Peripherals
use this menu to specify your settings for integrated peripherals.
Power Management Setup
use this menu to specify your settings for power management.
H/W Monitor 
this entry shows the status of your CPu, fan, warning for overall system status.  
BioS Setting Password
use this menu to set BioS setting Password.
Cell Menu
use this menu to specify your settings for frequency/ voltage control. 
						

							
2
MS-7599

M-Flash
use  this  menu  to  read/  flash  the  BioS  from  storage  drive  (Fat/  Fat2  format 
only). 
Load Fail-Safe defaults
use this menu to load the BioS default values that are factory settings for system 
operations.
Load optimized defaults
use  this  menu  to  load  factory  default  settings  into  the  BioS  for  stable  system 
performance operations.
Save & exit Setup
Save changes to CMoS and exit setup.
exit Without Saving
abandon all changes and exit setup.
Cell Menu
Current CPu/dRaM Frequency 
it shows the current frequency of CPu/Memory. Read-only. 
						

							
24

CPu Specifications
Press    to  enter  the  sub-menu. this  submenu  shows  the  information  of 
installed CPu.
CPu technology Support
Press  to enter the sub-menu.  this sub-menu shows the technologies 
that the installed CPu supported.
aMd Cool’n’quiet
the  Cool’n’quiet  technology  can  effectively  and  dynamically  lower  CPu  speed 
and  power consumption.
iMPoRtant
to  ensure  that  Cool’n’quiet  function  is  ac
-tivated  and  will  be  working  properly,  it  is required to double confirm that: Run  BioS  Setup,  and  select  Cell  Menu. under 
Cell Menu, find aMd Cool’n’quiet, 
and set this item to “enabled”.
enter  Windows,  and  select  [Start]->[Set
-
tings]->[Control Panel]->[Power  options]. 
enter 
Power  options  Properties  tag,  and select Minimal Power Management under Power schemes.
adjust CPu FSB Frequency (MHz)
this item allows you to adjust the CPu FSB frequency.
adjust CPu Ratio
this item is used to adjust CPu clock multiplier (ratio).  it is available only when the 
processor supports this function.
adjusted CPu Frequency (MHz)
it shows the adjusted CPu frequency. Read-only.
adjust CPu-nB Ratio
this item is used to adjust CPu-nB ratio.
adjusted CPu-nB Frequency (MHz)
it shows the adjusted CPu-nB frequency. Read-only.
advanced Clock Calibration
this  item  is  for  overclock.  Setting  to  [enabled]  allows  you  to  set  the  CPu  Ratio 
higher. it is available only when the processor supports this function.
auto overClock technologySetting this item to [Max FSB] allows the system to detect the maximum FSB clock 
and  to  overclock  automatically. if  overclocking  fails  to  run,  you  can  try  the  lower 
FSB clock for overclocking successfully.
*
* 
						

							
25
MS-7599

MultiStep oC Booster
this item is used to avoid the BioS might crash with overclocking. disabled  disable this item, apply oC settings during PoSt.
Mode   Slight oC during PoSt and then apply full oC when loading the  
  oS   
Mode 2  Load the oS then apply the oC settings.
Memory-Z
Press  to enter the sub-menu.
diMM~4 Memory SPd information
Press  to enter the sub-menu.  this sub-menu displays the informations 
of installed memory.
advance dRaM Configuration
Press  to enter the sub-menu.
dRaM timing Mode
this field has the capacity to automatically detect the  dRaM timing. if you set 
this field to [dCt 0], [dCt  ] or [Both], some fields will appear and selectable. 
dCt 0 controls channel a and dCt controls channel B.
dRaM drive Strength
this  feature  allows  you  to  control  the  memory  data  bus’  signal  strength.  in-creasing  the  drive  strength  of  the  memory  bus  can  increase  stability  during overclocking.
dRaM advance Control
this field has the capacity to automatically detect the advanced dRaM timing. 
if  you  set  this  field  to  [dCt  0],  [dCt  ]  or  [Both],  some  fields  will  appear  and 
selectable.
t/2t Memory timing
this  field  controls  the  SdRaM  command  rate.  Selecting  [t]  makes  SdRaM 
signal  controller  to  run  at t  (t=clock  cycles)  rate.  Selecting  [2t]  makes 
SdRaM signal controller run at 2t rate. 
dCt unganged Mode
this feature is used to integrate two 64-bit dCts into a 28-bit interface.
Bank interleaving
Bank  interleaving is an important parameter for improving overclocking capabil-
ity of memory. it allows system to access multiple banks simultaneously.
Power down enable
this is a memory power-saving technology. When the system does not access 
memory  over  a  period  of  time,  it  will  automatically  reduce  the  memory  power supply.
MemClk tristate C/atLVid
this setting allows you to enable/disable the MemClk  tristating during C and 
atLVid. 
						

							
26

FSB/dRaM Ratio
this item will allow you to adjust the ratio of FSB to memory.
adjusted dRaM Frequency (MHz)
it shows the adjusted memory frequency. Read-only.
Ht Link Speed
this item allows you to set the Hyper-transport Link speed. Setting to [auto], the 
system will detect the Ht link speed automatically.
adjusted Ht Link Frequency (MHz)
it shows the adjusted Ht link frequency. Read-only.
adjust PCi-e Frequency (MHz)
this item allows you to adjust the PCi-e frequency.
auto disable dRaM/PCi Frequency
When set to [enabled], the system will remove (turn off) clocks from empty diMM 
and PCi slots to minimize the electromagnetic interference (eMi).
CPu Vdd Voltage (V)/ CPu-nB Vdd Voltage (V)/ CPu Voltage (V)/ CPu-nB Voltage (V)/ dRaM Voltage (V)/ nB Voltage (V)/ Ht Link Voltage (V)/ SB Voltage (V)
these items are used to adjust the voltage of CPu, Memory and chipset.
Spread SpectrumWhen  the  motherboard’s  clock  generator  pulses,  the  extreme  values  (spikes)  of 
the pulses create  eMi (electromagnetic  interference). the Spread Spectrum func-
tion  reduces  the  eMi  generated  by  modulating  the  pulses  so  that  the  spikes  of 
the  pulses  are  reduced  to  flatter  curves.  if  you  do  not  have  any eMi  problem, 
leave  the  setting  at  disabled  for  optimal  system  stability  and  performance.  But  if 
you are plagued by  eMi, set to enabled for  eMi reduction. Remember to disable 
Spread Spectrum if you are overclocking because even a slight jitter can introduce a temporary boost in clock speed which may just cause your overclocked proces-sor to lock up.
iMPoRtant
if you do not have any  eMi problem, leave the setting at [disabled] for optimal 
system  stability  and  performance.  But  if  you  are  plagued  by  eMi,  select  the 
value of Spread Spectrum for eMi reduction. 
the greater the Spread Spectrum value is, the greater the  eMi is reduced, and 
the  system  will  become  less  stable.  For  the  most  suitable  Spread  Spectrum 
value, please consult your local eMi regulation.
Remember to disable Spread Spectrum if you are overclocking because even a slight jitter can introduce a temporary boost in clock speed which may just cause your overclocked processor to lock up.
*
*
* 
						

							
27
MS-7599

Load optimized defaults
you can load the default values provided by the mainboard manufacturer for the 
stable performance. 
						

							
28 
						

							
29
MS-7599
한국어
시작하기
770-C5/  770-C45  시리즈  (MS-7599  v.x) atX  메인보드를  선택해주셔서  감사
합니다.  770-C5/  770-C45  시리즈는  최적의  시스템  효율을  위해 aMd®  770  & SB70/  SB750/  SB700  칩셋에  기반을  둔  제품입니다.  고급의 aMd®  aM 프로세
서에 적합하게 디자인된 770-C5/ 770-C45 시리즈는 고성능과 전문적인 데스크톱 
플랫폼 솔루션을 제공합니다.
레이아웃 
						

							
0

지원되는 프로세서aM 패키지의 aMd® athlon™ X2/ X/ X4 & Phenom™ii X/ X4 프로세서(CPu에 대한 최신 정보는http://www.msi.com/index.php?func=cpuform2 참조)
HypertransportHypertransport™ .0 최대 5.2 Gt/s 지원
칩셋노스 브릿지: aMd® 770 칩셋
사우스 브릿지: aMd® SB70/ SB750 (옵션)/ SB700 (옵션) 칩셋
지원되는 메모리 ddR 800/ 066/ / 600*(oC) SdRaM ( 합계 최대 6GB)
4 ddR diMMs (240핀/ .5V)
(* oC = overclocking, 호환 가능한 부품에 대한 자세한 내용은http://www.msi.com/index.php?func=testreport 를 참조하십시오.)
LanPCie Lan 0/ 00/ 000 by Realtek® RtL 8dL 지원
오디오Realtek® aLC888S/ aLC885 에 의해 통합된 칩
7.채널 오디오 출력 지원
.0 Spec 과 호환
ide aMd® SB70/ SB750 (옵션)/ SB700 (옵션) 에 의한 ide 포트 개
ultra dMa 66/00/, Pio 및 버스 마스터 작동 모드 지원
Sata aMd® SB70/ SB750 (옵션)/ SB700 (옵션) 의한 Sataii 포트 6개
최대 .0 Gb/s 의 저장 및 데이터 전송 지원
Raid aMd® SB70/ SB750 (옵션)/ SB700 (옵션)에 의해 Raid 0/ / 0 또는 JBod 
모드 지원하는 Sata~6 
플로피 플로피 포트 개
 Fdd with 60 kB, 720 kB, .2 MB, .44 MB and 2.88 MB 지원
■
■
■■
■■
■
■■■
■■
■■
■
■■
사양