Mr.Bricolage Lawn Mower MBE 1135P MBE 1339P Instructions Manual

6EN
6.1 STONE-GUARD ASSEMBLY
Attach the stone-guard by inserting the pin (1)
and the spring (2) as shown.  
First, insert the pin into the right-hand hous-
ing (4).  Next fit the eyelet end (3) of the
spring into the central slot, and lastly insert
the other end of the pin in place (5).
6.2 HANDLE ASSEMBLY
Intsert into the holes on the chassis
the lower part of the handle (1) and
lock into position with the screws (2)
provided, paying attention to screw
them correctly into the upper hole
Attach the upper...

7EN
6.3 GRASS-CATCHER  ASSEMBLY
Insert the frame (11) into the sack (12)
and attach the plastic bars (13) using
a screwdriver, as shown in the draw-
ing.
6.4 WHEELS ASSEMBLY
To attach the wheels, follow the
steps shown. 
ttach the wheels selecting one of the
holes for the preferred cutting
heights, fully tightening the pin (1)
using the wrench (2) provided.
Ø 130
Ø 160
1
1
2
2  

8EN
7.1 DUAL ACTION SWITCH
The engine is controlled by a dual
action switch to prevent starting it
accidentally. 
To start, press the button (2) and pull
the lever (1). 
The engine automatically stops when
the lever (1) is released.
7.2 CUTTING HEIGHT ADJUSTMENT
The cutting height is adjusted by
attaching the wheels to the required
hole, fully tightening the pin (1) using
the wrench (2) provided. 
All the wheels must be at the same
height. 
MAKE THIS ADJUSTMENT ONLY
WHEN THE BLADE IS STOPPED.
7....

9EN
8.1 FITTING THE GRASS-CATCHER
Lift the stone-guard and attach the grass-catcher (1) correct-
ly as shown in the drawing.
8.2 STARTING
Connect the extension cable correctly as indicat-
ed according to the different types of  clips.
Start the engine by pressing the safety push-but-
ton (2) and pulling the switchgear lever (1).
8.3 ADVICE FOR CORRECT CUTTING
While cutting, ensure that the electric cable is
always behind you and on the area of grass
already cut.
The lawn will look better if it is always...

10EN
IMPORTANT – Regular, careful maintenance is essential for keeping the safety level
and original performance of the machine unchanged in time.
Store the lawnmower in a dry place.
1) Wear strong working gloves during any cleaning, maintenance or adjustment operation
on the machine.
2) Remove the grass debris after each cut and mud accumulated inside the chassis to
avoid their drying and thus making the next start-up difficult.
9.1 BLADE REMOVAL AND FITTING
All operations on the blade should be...

11EN
10. TROUBLESHOOTING
Electric mower does not
work
Electric mower trips my
mains circuit-breakers
Cut grass is not blown into
the gras box
Mower struggles to cut
grass– Is there power to the mower?
– Is the amperage of the sock-
et’s contact breaker sufficient?
– Do you have other electrical
equipment running at the
same time?
– Is there a burnig smell, or
smoke?
– Has the blade received a
knock?
– Is the mower’s blade housing
clean underneath?
– Is the blade in working order
and sharp?– Check your...

1ES
Queremos agradecerle sobre todo por 
encontrarse entre nuestros clientes y hemos 
predispuesto todo lo necesario para ofrecerle 
un producto eficiente y conforme
a las directivas actualmente en vigor.
Este manual le ayudará a montar y usar la máquina
que acaba de comprar.
Estamos siempre a su disposición. 

2ES
3) No pasar nunca con la cortadora de pasto sobre el cable
eléctrico. Durante el corte siempre hay que arrastrar el cable
detrás de la cortadora de pasto y siempre de la parte de la
hierba cortada. Utilizar el enganche cable como se indica en
este libro para evitar que el cable se desenchufe accidental-
mente, asegurando contemporáneamente su correcta intro-
ducción en el enchufe sin forzarlo.
4) No tirar nunca del cable de alimentación para mover la
cortadora de pasto, ni tirar del cable para...

3ES
ra de pasto, y sobre todo del motor, los residuos de hierba,
hojas o grasa excesiva. No dejar los contenedores con la
hierba cortada en el interior de un local.
3) Controlar frecuentemente el parapiedras y el saco para
verificar su usura o deterioro.
4) Verificar periódicamente el estado de los cables eléctricos
y sustituirlos en el caso en que estén deteriorados o su ais-
lamiento esté dañado. No tocar nunca un cable eléctrico con
corriente si está mal aislado. Desenchufarlo antes de las...