Mountfield Lawn Mower 2125M - 2135H Instructions Manual

2125M - 2135H
8211-0090-01
INSTRUCTIONS FOR USEMODE D’EMPLOI
GEBRUIKSAANWIJZING
GEBRAUCHSANWEISUNG
ИНСТРУКЦИЯ  ПОЛЬЗОВАТЕЛЯ EN .... 6
FR... 18
NL ... 31
DE .. 44
RU .. 58 

2
SF
G
E
E
G
H
K, L
J
A
B
1
2 4 3
5 

3
M
N P
 
Q U
T
2135H
O
Q
P
QR
U
T2125M
P
Q
6
8 10 7
9 11 

4
01
Max
R S
G F E
E
K 
L
12
14 16 13
15 17 

5
N
M O
R
18
20 19
21 

6
ENGLISHEN
1 GENERAL
This symbol indicates WARNING. 
Serious personal injury and/or damage 
to property may result if the 
instructions are not followed carefully.
You must read these instructions for use 
and the accompanying pamphlet 
“SAFETY INSTRUCTIONS” 
carefully, before starting up the 
machine.
1.1 SYMBOLS
The following symbols appear on the machine. 
They are there to remind you of the care and 
attention required duri ng use and maintenance.
This is what the symbols mean: Warning!
Read the...

7
ENGLISHEN
c. Fill with petrol before starting the motor. 
Never remove the filler cap or fill with petrol 
while the engine is running or still warm.
d. If petrol is spilt, do not  try to start the engine 
but instead move the machine away from the 
place where the spillage  occurred and avoid any 
possible causes of sparks  until the petrol fumes 
have evaporated.
e. Do not forget to screw the cap on the petrol 
tank and the storage c ontainer after filling.
• Replace faulty silencers.
• Before use,...

8
ENGLISHEN
• The machine may not be used without 
accessories/tools being installed in the 
machine’s tool mounts. Driving without 
accessories can have a negative effect on the 
stability of the machine.
• Take care when using grass collectors and other  accessories. These can alter the machine’s 
stability. Particularly on slopes.
• Disengage the drive to the accessories, shut off  the engine and disconnect the spark plug cable 
or remove the starter key:
a. To remove sticks and rubbish or when the...

9
ENGLISHEN
3 ASSEMBLY
To avoid injury and damage to people 
and property, do not use the machine 
until all the measures under 
“ASSEMBLY” have been carried out.
3.1 ASSEMBLY COMPONENTS
Components that are to be used at assembly are 
included in the delivery. See fig. 1. 
Supplied in bag:
Pos No. Designation Dimension
A 1 Towing plate
B 2 Screw with flange 8 x 20
C 2 Screw for battery
D 2 Nut for battery
E 4 Washer 8.4 x 24 x 2.0
F 2 Shoulder washer
G 4 Screw 8 x 20
H 2 Screw knob
I 2 Ignition key
J 1...

10
ENGLISHEN
3. From the outside, check whether no washers, the 0.5 mm washer, the  1.0 mm washer or both 
washers can be inserted into the gap. The 
washer/washers must not  be forced in, as there 
must be a little axial play.
4. Pull out the cotter pin and disMantle the  steering wheel jacket.
5. Install the washer/washers in accordance with  point 3 above.
6. Install the steering column jacket on the  steering column and secure by knocking in the 
cotter pin fully. Use a counterhold.
3.6 TOWING HITCH...