Motorola Xpr 7000 Seris Basic 68009498001 A Manual

Transceiver Performance Testing Display Model Test Mode 3-5
* See Table 3-4 Table 3-5.  Transmitter Performance Checks
Te s t  N a m eCommunications 
AnalyzerRadio Test Set Comments
Reference 
FrequencyMode: PWR MON
4th channel test 
frequency*
Monitor: Frequency 
error
Input at RF In/OutTEST MODE,
Test Channel 4 
carrier squelchPTT to 
continuously
transmit
(during the 
performance 
check)Frequency error to be 
±604Hz for UHF
±204Hz for VHF
Power RF As above As above As above Low Power:
1.0 – 1.6W...

3-6Transceiver Performance Testing Display Model Test Mode
* See Table 3-4Table 3-6.  Receiver Performance Checks
Te s t  N a m eCommunications 
AnalyzerRadio Test Set Comments
Reference 
FrequencyMode: PWR MON
4th channel test
frequency*
Monitor: Frequency error
Input at RF In/OutTEST MODE,
Test Channel 4 
carrier squelch 
output at 
antennaPTT to 
continuously 
transmit
(during the 
performance 
check)Frequency error to be 
±604Hz for UHF
±204Hz for VHF
Rated Audio Mode: GEN
Output level: 1.0mV RF
6th...

Transceiver Performance Testing Display Model Test Mode 3-7
3.3.3 LED Test Mode
1. Press and hold Side Button 1 after Display Test Mode. The radio beeps once and displays 
“LED Test Mode”. 
2. Upon any button/key press, the radio lights the red LED and displays “Red LED On”.
3. Consequently, upon any button/key press, the red LED is turned off and the radio lights the 
green LED and displays “Green LED On”.
4. Upon any successive button/key press, the green LED is turned off, and the radio shall light...

3-8Transceiver Performance Testing Display Model Test Mode
3.3.8 Battery Check Test Mode
1. Press and hold Side Button 1 after Audio Loopback Earpiece Test Mode. The radio beeps 
once and momentarily displays “Battery Check Test Mode”. 
2. The radio will display the following:
Figure 3-1.  Battery Check Test Mode Display
3.3.9 Button/Knob/PTT Test Mode
1. Press and hold Side Button 1 after Battery Check Test Mode. The radio beeps once and 
displays “Button Test”(line 1). 
2. Rotate the Vo l u m e  K n o...

Transceiver Performance Testing Display Model Test Mode 3-9
- Press BACK, “129/1” appears & radio beeps; release, “129/0” appears & radio beeps.
- Press 
W, “128/1” appears & radio beeps; release, “128/0” appears & radio beeps.
- Press 
X, “130/1” appears & radio beeps; release, “130/0” appears & radio beeps.
- Press 
▲, 135/1 appears & radio beeps; release, 135/0 appears & radio beeps.
- Press 
▼, 136/1 appears & radio beeps; release, 136/0 appears & radio beeps.
3.4 Display Model Test Mode
3.4.1...

3-10Transceiver Performance Testing Non-Display Model Test Mode
3.5 Non-Display Model Test Mode
3.5.1 Entering Non-Display Radio Test Mode
1. Turn the radio on.
2. Within 10 seconds after “Self Test” is complete, press Side Button 2 five times in succession.
3. The radio beeps.
3.5.2 RF Test Mode
When the radio is operating in its normal environment, the radios microcontroller controls the RF 
channel selection, transmitter key-up, and receiver muting, according to the customer codeplug 
configuration....

Transceiver Performance Testing Non-Display Model Test Mode 3-11
3.5.5 Earpiece Tone Test Mode
1. Press and hold Side Button 1 after Speaker Tone Test Mode. The radio beeps once.
2. The radio generates a 1 KHz tone with the earpiece.
3.5.6 Audio Loopback Earpiece Test Mode
1. Press and hold Side Button 1 after Earpiece Tone Test Mode. The radio beeps once.
2. The radio shall route any audio on the external mic to the earpiece. 
3.5.7 Battery Check Test Mode
1. Press and hold Side Button 1 after Audio...

Notes
3-12Transceiver Performance Testing Non-Display Model Test Mode 

Chapter 4 Radio Programming and Tuning
4.1 Introduction
This chapter provides an overview of the MOTOTRBO Customer Programming Software (CPS), as 
well as the Tuner and AirTracer applications, which are all designed for use in a Windows 2000/XP/
Windows 7 environment. These programs are available in one kit as listed in Table 4-1. An 
Installation Guide is also included with the kit.
4.2 Customer Programming Software Setup
The CPS programming setup, shown in Figure 4-1 is used to program the radio....

4-2Radio Programming and Tuning: Radio Tuning Setup
internal error logs from MOTOTRBO radios. The saved files can be analyzed by trained Motorola 
personnel to suggest improvements in system configurations or to help isolate problems.
4.4 Radio Tuning Setup
A personal computer (PC), Windows 2000/XP/Windows 7and a tuner program are required to tune 
the radio. To perform the tuning procedures, the radio must be connected to the PC, radio interface 
box (RIB), and test equipment setup as shown in Figure...