Motorola Xpr 7000 Seris Basic 68009498001 A Manual

Introduction: Specifications1-13
 Military Standards
Applicable 
MIL–STD 810C 810D 810E 810F 810G*
Methods Procedures Method
s Procedures Methods  Procedures  Methods  Procedures Methods Prodecures
Low Pressure  500.1 I 500.2 II500.3 II  500.4 II  500.5 II
High 
Temperature 501.1 I, II 501.2 I/A1,II/
A1501.3 I-A1, II/
A1501.4 I/Hot, II/
Hot 501.5 I/A1, II
Low 
Temperature 502.1 I 502.2 I/C3, II/
C1502.3 I-C3, II/
C1 502.4 I-C3, II/
C1502.5 I, II
Temperature 
Shock 503.1 - 503.2 I/A1/C3 503.3 I/A1/C3...

1-14Introduction: Specifications
* Operating temperature specification with LiIon battery is -10 °C to +60 °C.
Operating temperature specification with NiMH battery is -20 °C to +60 °C.
 Environmental Specifications
*Operating Temperature  -30 °C to +60 °C 
Storage Temperature  -40 °C to +85 °C 
Thermal Shock Per MIL-STD 
Humidity Per MIL-STD 
ESD  IEC 61000-4-2 Level 3 
Water Intrusion  IEC 60529 -IP57 
Packaging Test  MIL-STD 810D and E  

Chapter 2 Test Equipment and Service Aids
2.1 Recommended Test Equipment
The list of equipment contained in Table 2-1 includes most of the standard test equipment required 
for servicing Motorola portable radios.
Table 2-1.  Recommended Test Equipment
Equipment Characteristics Example Application
Service
MonitorCan be used as a 
substitute for items 
marked with an asterisk 
(*)Aeroflex 3920 
(www.aeroflex.com),Frequency/deviation meter and 
signal generator for wide-range 
troubleshooting and alignment...

2-2Test Equipment and Service Aids: Service Aids
2.2 Service Aids
Table 2-2 lists the service aids recommended for working on the radio. While all of these items are 
available from Motorola, most are standard workshop equipment items, and any equivalent item 
capable of the same performance may be substituted for the item listed.
* Earlier versions of programming cables will not work with the radio. Table 2-2.  Service Aids
Motorola 
Part No.Description Application
RLN4460_Portable Test SetEnables...

Test Equipment and Service Aids: Programming, Testing and Alignment Cable 2-3
2.3 Programming, Testing and Alignment Cable
Figure 2-1.  Programming, Testing and Alignment Cable
#1 #14 #25
#13#4
#1
#2
#12 #11#1P1
P2
P3 

2-4Test Equipment and Service Aids: Programming, Testing and Alignment Cable
Figure 2-2.  Pin Layout of Side Connector Table 2-3.  Pin Configuration of Side Connector
CONNECTION
P1 P2 P3
Pin Pin Pin Function
1 GROUND
1 3 VCC (5V)
34DATA+
25DATA-
16 4 6 GROUND
1 & 5
7 EXTERNAL SPEAKER+
2 & 7
8 EXTERNAL SPEAKER-
20
9 EXTERNAL PTT
17
10 EXTERNAL MIC+
16
11 EXTERNAL MIC-
slot for accessory
connector hook
1
2
3
4
5
6
7
8
9
10
11
12
GPIO_0
Spkr +
Spkr -
Mic +
Mic - GPIO_3
GPIO_41-Wire
Vbus
D+
D-
GND 

Chapter 3 Transceiver Performance Testing
3.1 General
These radios meet published specifications through their manufacturing process by utilizing high- 
accuracy laboratory-quality test equipment. The recommended field service equipment approaches 
the accuracy of the manufacturing equipment with few exceptions. This accuracy must be 
maintained in compliance with the manufacturer’s recommended calibration schedule.
Although these radios function in digital and analog modes, all testing is done in analog...

3-2Transceiver Performance Testing Setup
Oscilloscope Source: Mod
Oscilloscope Horizontal: 10mSec/Div
Oscilloscope Vertical: 2.5kHz/Div
Oscilloscope Trigger: Auto
Monitor Image: Hi
Monitor Bandwidth: Narrow
Monitor Squelch: Middle setting
Monitor Vol: 1/4 settingCurrent: 2.5A Table 3-1.  Initial Equipment Control Settings
Service Monitor Power Supply Test Set 

Transceiver Performance Testing Display Model Test Mode 3-3
3.3 Display Model Test Mode
3.3.1 Entering Display Radio Test Mode
1. Turn the radio on.
2. Within 10 seconds after Self Test is complete, press Side Button 2 five times in succession
3. The radio beeps and will show a series of displays that will give information regarding various 
version numbers and subscriber specific information. The displays are described in Table 3-2.
3.3.2 RF Test Mode
When the radio is operating in its normal...

3-4Transceiver Performance Testing Display Model Test Mode
2. Each short press of Side Button 1 toggles the channel spacing between 25 kHz, 12.5 kHz 
and 20 kHz as. The radio beeps once when radio toggles to 20kHz, beeps twice for 25 kHz 
and beeps three times for 12.5 kHz.
3. Turning of the Channel Knob changes the test channel from 1 to 14 as described in 
Table 3-4. The radio beeps in each position.Table 3-3.  Test Environments
No. of 
BeepsDescription Function
1Carrier Squelch
(CSQ)RX: if carrier...