Motorola Wing 5 Manual

ACCESS-LIST 12 - 27
Examples
rfs7000-37FABE(config-mac-acl-test)#show context
mac access-list test
 permit host 11-22-33-44-55-66 any log mark 8021p 3 rule-precedence 600
 permit host 22-33-44-55-66-77 host 11-22-33-44-55-66 type ip log rule-precedence 610
deny any host 33-44-55-66-77-88 log rule-precedence 700
rfs7000-37FABE(config-mac-acl-test)#no deny any host 33-44-55-66-77-88 log rule-
precedence 700
rfs7000-37FABE(config-mac-acl-test)#show context
mac access-list test
 permit host 11-22-33-44-55-66...

12 - 28 WiNG CLI Reference Guide
12.2.3 permit
ip-access-list
Configures a permit MAC ACL
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
permit [|any|host
permit [ |any|host ] 
[ |any|host ] 
(dot1p ,type [8021q||aarp|appletalk |arp|ip|ipv6|mint|rarp|
wisp|ipx],vlan ) [log mark [8021p |dscp ]|
mark [8021p |dscp ]|rule-precedence ] 
{rule-description }
Parameters
• permit [ |any|host ] 
[ |any|host ] 
(dot1p...

ACCESS-LIST 12 - 29
any Identifies all devices as the destination to permit access
host  Identifies a specific host as the destination to permit access
  – Specify the MAC address of the host.
dotp1p  Configures the 802.1p priority value. Sets the service classes for traffic handling
  – Specify a value from 0 - 7.
type [8021q|

12 - 30 WiNG CLI Reference Guide
Usage Guidelines
The permit command in the MAC ACL disallows traffic based on layer 2 (data-link layer) information. A MAC access list 
permits traffic from a source MAC address or any MAC address. It also has an option to allow traffic from a list of MAC 
addresses (based on the source mask).
The MAC access list can be configured to allow traffic based on VLAN information, or Ethernet type. Common types 
include:



 802.1q
The controller (by default) does not allow...

CHAPTER 13 DHCP-SERVER-POLICY
This chapter summarizes DHCP server policy commands within CLI structure. Dynamic Host Control Protocol (DHCP) is a 
protocol that automatically assigns network IP addresses to clients to enable them to participate in the network. DHCP 
keeps track of IP address assignments, their lease times and their availability for use by clients.
Use the (config) instance to configure DHCP server policy configuration commands. To navigate to the 
DHCP server policy instance, use the...

13 - 2 WiNG CLI Reference Guide
13.1 dhcp-server-policy
Table 13.1summarizes DHCP server policy commands
Table 13.1dhcp-server-policy commands
Command Description Reference
bootpConfigures a BOOTP specific configurationpage 13-3
dhcp-classConfigures a DHCP server classpage 13-4
dhcp-poolConfigures a DHCP server address poolpage 13-11
noNegates a command or sets its defaultpage 13-55
optionDefines the DHCP option used in DHCP poolspage 13-57
pingSpecifies ping parameters used by a DHCP serverpage 13-58...

DHCP-SERVER-POLICY 13 - 3
13.1.1 bootp
dhcp-server-policy
Configures a BOOTP specific configuration. Bootstrap Protocol (BOOTP) is used by UNIX diskless workstations to obtain 
the network location of their boot image and IP address. A BOOP configuration server also assigns an IP address from a 
configured pool of IP addresses.
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
bootp ignore
Parameters
• bootp...

13 - 4 WiNG CLI Reference Guide
13.1.2 dhcp-class
dhcp-server-policy
A DHCP user class applies different DHCP settings to a set of wireless clients. These wireless clients are grouped under 
the same DHCP class. This class is configured on the DHCP server to provide differentiated service.
Command Description Reference
dhcp-classConfigures a DHCP class and its settingspage 13-5 

DHCP-SERVER-POLICY 13 - 5
13.1.2.1 dhcp-class
dhcp-server-policy
Configures a DHCP server class and opens a new mode. For more information, see dhcp-class-mode.
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
dhcp-class 
Parameters
• dhcp-class 
Examples
rfs7000-37FABE(config-dhcp-policy-test)#dhcp-class dhcpclass1
rfs7000-37FABE(config-dhcp-policy-test-class-dhcpclass1)#?...

13 - 6 WiNG CLI Reference Guide
13.1.2.2 dhcp-class-mode
dhcp-class
Use DHCP class mode commands to configure a DHCP server class.
Table 13.2 summarizes DHCP class commands
Ta b l e  1 3 . 2dhcp-class commands
Command Description Reference
multiple-user-classEnables the multiple user class optionpage 13-7
noNegates a command or sets its defaultpage 13-8
optionConfigures DHCP server optionspage 13-9
clrscrClears the display screenpage 5-3
commitCommits (saves) changes made in the current sessionpage 5-4...