Motorola Wing 5 Manual

USER EXEC MODE COMMANDS 2 - 45
2.1.20 traceroute
User Exec Commands
Traces the route to a defined destination
Use ‘--help’ or ‘-h’ to display a complete list of parameters for the traceroute command
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
traceroute 
Parameters
• traceroute 
Examples
rfs7000-37FABE>traceroute --help
BusyBox v1.14.1 () multi-call binary
Usage: traceroute [-FIldnrv] [-f 1st_ttl] [-m max_ttl] [-p port#] [-q nqueries]...

2 - 46 WiNG CLI Reference Guide
2.1.21 watch
User Exec Commands
Repeats the specified CLI command at periodic intervals
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
Syntax
watch  
Parameters
• watch  
Examples
rfs7000-37FABE>watch 45 page
rfs7000-37FABE>
rfs7000-37FABE>watch 45 ping 172.16.10.2
PING 172.16.10.2 (172.16.10.2): 100 data bytes
108 bytes from 172.16.10.2: seq=0 ttl=64 time=0.725 ms
108 bytes from 172.16.10.2: seq=1 ttl=64 time=0.464 ms
108 bytes from...

CHAPTER 3 PRIVILEGED EXEC MODE 
COMMANDS
Most PRIV EXEC commands set operating parameters. Privileged-level access should be password protected to prevent 
unauthorized use. The PRIV EXEC command set includes commands contained within the USER EXEC mode. The PRIV EXEC 
mode also provides access to configuration modes, and includes advanced testing commands. 
The PRIV EXEC mode prompt consists of the hostname of the device followed by a pound sign (#). 
To access the PRIV EXEC mode, enter the following at...

3 - 2 WiNG CLI Reference Guide
  page           Toggle paging
  ping           Send ICMP echo messages
  pwd            Display current directory
  reload         Halt and perform a warm reboot
  remote-debug   Troubleshoot remote system(s)
  rename         Rename a file
  revert         Revert changes
  rmdir          Delete a directory
  self           Config context of the device currently logged into
  service        Service Commands
  show           Show running system information
  ssh...

PRIVILEGED EXEC MODE COMMANDS 3 - 3
3.1 Privileged Exec Mode Commands
Table 3.1 summarizes the PRIV EXEC Mode commands:. 
Table 3.1Privileged Exec Commands
Command Description Reference
ap-upgradeEnables an automatic firmware upgrade on an adopted APpage 3-5
archiveManages file archive operationspage 3-10
bootSpecifies the image used after rebootpage 3-12
cdChanges the current directorypage 3-13
change-passwdChanges the password of a logged userpage 3-14
clearClears parameters, cache entries, table...

3 - 4 WiNG CLI Reference Guide
pageToggles wireless controller pagingpage 3-58
pingSends ICMP echo messages to a user-specified locationpage 3-59
pwdDisplays the current directorypage 3-60
reloadHalts the wireless controller and performs a warm rebootpage 3-61
renameRenames a file in the existing file systempage 3-63
rmdirDeletes an existing file from the file systempage 3-64
selfDisplays the configuration context of the devicepage 3-65
sshConnects to another device using a secure shellpage 3-66...

PRIVILEGED EXEC MODE COMMANDS 3 - 5
3.1.1 ap-upgrade
Privileged Exec Commands
Enables an automatic firmware upgrade on an adopted AP or a set of APs. APs of the same type can be upgraded together. 
Once APs have been upgraded, they can be forced to reboot. This command also loads the firmware on to the wireless 
controller.
The AP upgrade command also upgrades APs in a specified RF Domain.
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000...

3 - 6 WiNG CLI Reference Guide
Parameters
• ap-upgrade [|all] {no-reboot|reboot-time |upgrade-time  
{no-reboot|reboot-time }}
• ap-upgrade [ap621|ap650|ap6511|ap6521|ap6532|ap71xx] all {no-reboot|reboot-time 
|upgrade-time  {no-reboot|reboot-time }}
[|all] Upgrades firmware on a specified AP or all APs adopted by the wireless controller
  – Specify the MAC address or hostname of the AP.
 all – Upgrades all APs adopted by the wireless controller
no-reboot Optional. Disables automatic reboot after a...

PRIVILEGED EXEC MODE COMMANDS 3 - 7
• ap-upgrade cancel-upgrade [|all]
• ap-upgrade cancel-upgrade [ap621|ap650|ap651|ap6521|ap6532|ap71xx] all
• ap-upgrade cancel-upgrade on rf-domain [|all]
• ap-upgrade load-image [ap621|ap650|ap6511|ap6521|ap6532|ap71xx] 
cancel-upgrade [
|all]Cancels scheduled firmware upgrade on a specified AP or all APs adopted by the 
wireless controller
  – Specify the MAC address or hostname of the AP.
 all – Cancels scheduled upgrade on all APs
cancel-upgrade...

3 - 8 WiNG CLI Reference Guide
• ap-upgrade rf-domain [|all] [all|ap621|ap650|ap6511|
ap6521|ap6532|ap71xx] {no-reboot|no-via-rf-domain|reboot-time |
upgrade-time }
Examples
rfs7000-37FABE#ap-upgrade AP621 all
--------------------------------------------------------------------------
         CONTROLLER           STATUS                    MESSAGE
--------------------------------------------------------------------------
  00-15-70-37-FA-BE           Success         Queued 0 APs to upgrade...