Motorola Cp200 Detailed 6880309n62 C Manual
Have a look at the manual Motorola Cp200 Detailed 6880309n62 C Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 249 Motorola manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
6880309N62-CJune, 2005 UHF Troubleshooting Tables: Troubleshooting Table for Board and IC Signals 11-15 U480 Dual Opamp1 Unit 1 output 2.48 2Unit 1 (-) input2.48 3 Unit 1 (+) input 2.46 4GroundGND 5 Unit 2 (+) input 0.28 6Unit 2 (-) input0.29 7 Unit 2 output 0 8Vcc4.96 U490 Audio Power Amp1 Enable/shutdown 0.12 (Unsquelched) 2Bias reference3.26(Unsquelched) 3 (+) input 3.26 (Unsquelched) 4(-) input3.27(Unsquelched) 5 (-) output 3.25 (Unsquelched) 6Vcc7.48(Unsquelched) 7 Ground GND 8(+) output3.29(Unsquelched) U510 Dual Opamp1 Unit 1 output 1.75 2Unit 1 (-) input1.56 3 Unit 1 (+) input 1.55 4GroundGND 5 Unit 2 (+) input 1.55 6Unit 2 (-) input1.56 7 Unit 2 output 1.38 8Vcc4.96 1. All voltages are measured with a high-impedance digital voltmeter and expressed in volts DC relative to ground (0V). 2. Voltages are measured with a DC input voltage of 7.50 + .02 volts DC applied to the battery connector (J301). 3. All voltages are measured in the squelched receive mode, unless otherwise indicated. 4. Voltages are identical for VHF and UHF models unless otherwise indicated. Table 11-4. Troubleshooting Table for Board and IC Signals (Continued) IC Designator Pin Pin Function DC Voltage Comments (Condition)
June, 20056880309N62-C Notes: 11-16UHF Troubleshooting Tables: Troubleshooting Table for Board and IC Signals
Chapter 12 UHF Schematic Diagrams, Overlays, and Parts Lists 12.1 Introduction This section provides schematic diagrams, overlays, and parts lists for the radio circuit boards and interface connections. 12.1.1 Notes For All Schematics and Circuit Boards * Component is frequency sensitive. Refer to the Electrical Parts List for value and usage. 1. Unless otherwise stated, resistance values are in ohms (K = 1000), capacitance values are in picofarads (pF) or microfarads (µF), and inductance values are in nanohenries (nH) or micro- henries (µH). 2. DC voltages are measured from point indicated to chassis ground using a Motorola DC multi- meter or equivalent. If the board has been removed from the chassis, the transmitter module mounting screws may be used for ground connection. (Note: The antenna nut bracket is not connected to ground.) Operating mode dependent voltages are followed by (RX) for receive mode, (TX) for transmit mode, (UNSQ) for unsquelched mode, etc. 3. RF voltages on VHF models are measured with a Fluke model 85 RF probe. The indicated voltages expressed in mV (RF) are DC level readings which correspond approximately 1:1 to the RF voltage level in mV rms. RF voltages in the Receiver Front End and Receiver Back End circuits are measured with an on-channel 100 mV (-7 dBm) RF signal applied to the antenna jack J140. 4. RF voltages on UHF models are measured both with a high-impedance RF voltmeter having a bandwidth in excess of 500 MHz (levels are expressed in dBm) and with a Fluke model 85 RF probe [levels are expressed in mV (RF)]. These indicated voltages are DC level readings which correspond approximately 1:1 to the RF voltage level in mV rms, and are only approxi- mate for UHF frequency measurements. RF voltages in the Receiver Front End and Receiver Back End circuits are measured with an on-channel 100 mV (-7 dBm) RF signal applied to the antenna jack J140. 5. Audio voltages are measured with a high-impedance AC rms voltmeter. The indicated volt- ages are expressed in mV rms. Receive mode voltages are followed by (RX) and are mea- sured with an on-channel signal with 1 kHz modulation at 60% deviation (3 kHz for 25 kHz channels, or 1.5 kHz for 12.5 kHz channels). Transmit mode voltages are followed by (TX) and are measured with a 1 kHz, 10 mV rms signal present at the external microphone input (accessory connector J471 pin 4 hot and pin 7 ground). 6. Reference Designators are assigned in the following manner: Ref. No. Series Circuit Block 1-99RF Front End 100-149 Transmitter RF Stages 150-200Transmitter Power Control 201-250 Frequency Synthesizer 251-300VCO
June, 20056880309N62-C 12-2UHF Schematic Diagrams, Overlays, and Parts Lists: Introduction 7. Circuit Block Interconnection Legend: 301-400 DC Regulation 401-450Microprocessor 451-550 Audio Name Description USWB+Unswitched Battery Voltage (always on) 5V 5 volts (regulated) 5R5 volts in RX mode only 5T 5 volts in TX mode only RESETLow-line reset signal from U320 to uP D3_3V Digital 3.3 volts (regulated) 3VAnalog 3 volts (regulated) TX_ENA Transmit enable signal from uP to transmitter PWR_SETDC voltage from ASFIC to TX power control DEMOD RX audio from backend to ASFIC BW_SELBackend filter BW select from ASFIC RSSI RX signal strength indication from IFIC to uP IF_IN/OUT44.85 MHz from 1st mixer to high IF filter RF_IN/OUT RX signal from antenna switch to front end MOD OUT/INTX modulation from ASFIC to synthesizer 16_8_MHZ Ref osc signal from synthesizer to ASFIC SYNTH_CSSynthesizer chip select from uP SPI_CLK Serial clock from uP SPI_DATA_OUTSerial data from uP LOCK Lock detect indication from synth to uP PRESCVCO freq feedback from VCOBIC to synth V_STEER Steering line voltage from synth to VCOs V_SFSuper-filtered 4.5 volts from synth to VCOBIC VCO_MOD TX modulation from ASFIC to synthesizer TRBTX/RX control from synth to VCOBIC RX_INJ Buffered RX VCO output to RX 1st mixer TX_INJTX VCO output to transmitter input Ref. No. Series Circuit Block
6880309N62-CJune, 2005 UHF Schematic Diagrams, Overlays, and Parts Lists: Speaker and Microphone Schematic 12-3 12.1.2 Six Layer Circuit Board Figure 12-1. Six-Layer Circuit Board: Copper Steps in Layer Sequence 12.2 Speaker and Microphone Schematic Figure 12-2. Speaker and Microphone Schematic 12.2.1 Speaker and Microphone Parts List Reference DesignatorMotorola Part No.Description MK15080258E16Microphone, electret SP1 5005679X04 Speaker assembly with connector LAYER 1 (L1) LAYER 2 (L2) LAYER 3 (L3) LAYER 4 (L4) LAYER 5 (L5) LAYER 6 (L6) INNER LAYERS SIDE 1 SIDE 2 MK1 SP11 2 1 2MATES WITH J470 ON RADIO BOARD MATES WITH J491 ON RADIO BOARD
June, 20056880309N62-C This Page Intentionally Left Blank 12-4UHF Schematic Diagrams, Overlays, and Parts Lists: Speaker and Microphone Schematic
UHF (403-440 MHz) Schematic Diagrams, Overlays, and Parts Lists (8486635Z03-O)12-568810309N62-CJune, 2005Chapter 12 UHF (403-440 MHz) Schematic Diagrams, Overlays, and Parts Lists (8486635Z03-O) CONTROLLERRX_BE SYNTH_UHF_R1TX_UHF_R1 VCO_UHF_R1RX_FE_UHF_R1 UHF R1 TX_INJ USWB+ 3V 5R PRESC RX_INJ TRBTX_INJ VCO_MOD V_SF V_STEER5R IF_OUT RX_I N RX_INJ 16_8_MHZ3V 5V LOC K MOD_IN PRESC SPI_CLK SPI_DATA_OUT SYNTH_CS TRB VCO_MODV_SF V_STEER5T PWR_SET RX_OUTTX_ENAUSWB+ 5V 5R 3V USWB+ 5V BW_SEL DEMOD IF_IN RSSI TX_EN A USWB+ 3V 5T 5T 5V 5R 3V 5R 5V 16_8_MHZ 3V 5R 5T 5V BW_SELDEMOD LOCK MOD_OUTPWR_SET RSSI SPI_CLK SPI_DATA_OUTSYNTH_CS Figure 12-3. UHF (403-440 MHz) Radio Circuit Block Diagram (8486635Z03-O)
12-6UHF (403-440 MHz) Schematic Diagrams, Overlays, and Parts Lists (8486635Z03-O)June, 200568810309N62-C 0.79V4.2V UHF R1 Front End 0.1uF C99 R20 5.6KR21 75 C36 1% 16pF C20 390pF C34 1.6% 6.2pF 15pF 1%C1 18pF 1%C33 C523 5.5% 0.55pF C37 1.6%6.2pF L40 27nH 18pF 1%C2 1.0% 10pF FE_RF_IN JC51 C12 NC82pF 0.6pF C524 IO3 3 IO44 R23 27K NCCR41 HSMS2829 IO11 2 IO2 C7 1.8pF 5.6%C3 NU C5 0C26 390pF 8.2pF IF1 1% 20pF C29 1.2%C11 L34 NU C40 9.85nH 2% 2%9.85nHC8SH40 SHIELD 1 L319.85nH 2%L3680nHL52 1.0%C44 10pFBFS505 Q2113FE_IF_OUT C35 1% 12pF0 C48RF BALUN 5 NC 4 63 2 1 T41 30pF NU C4 7 TP1 1 C43 1% 13pF 1% C10R24 1.2K C39 1% 12pF TP2 1SH1 SHIELD 1 13 218nHL55 CR1 2.4pF C30 1%22pFC13 4.2% 9.1pF 1.1%C27 NU C46 C42 1.8pF 5.6%C6 1.0%10pF390pF C25 R51 390pF 10% C21 L51 150nH51 L2 2%9.85nH L32 27nH 9.85nH 2%L33 2% 9.85nH L41C38 1% 16pF 2 5 6314 UMT1 Q22 C32 1.3%7.5pF C41 15pF 1% C28 1% 15pFC14 L1 2.4pF 4.2% C49 NU 9.85nH 2%4.5% 2.2pF 390pF C522 3.0%C521 C23 R25 5.6K3.3pF T42 5 NC 4 63 2 1 IF BALUN C31 1.1% 9.1pFL21 27nH 1KR40 C45 1% 22pF C9 1% 18pFFE_5R R22 5.6K RX_INIF_OUT RX_IN J5R 2 Figure 12-4. UHF (403-440 MHz) Receiver Front End Schematic Diagram (8486635Z03-O)
UHF (403-440 MHz) Schematic Diagrams, Overlays, and Parts Lists (8486635Z03-O)12-768810309N62-CJune, 2005 5V for 25kHz RX Back End (Overtone) 0V for 12.5kHz 3.39V 3.05V 0.74V 1.5V 2.1V When -47 dBm @ antenna 9.1pF 1.1%C5312 3 5V 1 23 D51 13 2D52 CR51C71 IF_DEMOD TC7W04F 17 0.1uF GND1 3 4 GND2 IN 1 OUT 2 U52-1 C69CFWC455EFL53 12K0.1uF C73 R521 IN2 OUT 4700pF FL54 CFWC455G GND1 3 GND24 0.1uFC55 5V 0.1uF C56C62 0.1uF C60 0.1uFC67 0.1uF R53 33K2.4K Q70MMBT3904 13 2 R60 C80 22pF 1% C59 2.7pFR73 1.8K NC R74 1.2K 62 1.6K U52-2TC7W04F 5.1KR80 R91 PBR941 Q5113 2 C93 3.6pFC90 0.1uF NUC63 L53 120pF0.1uF R82 1.2uH 2% L54 NU 1uHL81 5V C52 22pF4.7KR57C66 SH52 SHIELD 1 OU T I N10.1uF 44.395MHz TSS2_44_395MHZY51 2 GND 4 GND1 3 2 CC1 5 CC2 1 GND1 4 GND2 3IN6 OUT 44.85MHzMXF45FL51 4 VCC8 C58 3.9pF PWR_GNDU52-4 GND R81 10uFC910.1uFC65 1KR75 12K 20K C57 0.1uF9180468V04 3 GND IN 1 OU T2R64 FLTR FL52 C81 1% 33pFC70 IF_I N RFIN RFIN_DEC 2 5 RSSIOUT RSSI_FEED 9 6 VCC 130pF LIMIN LIMOUT11 13 LIM_DEC1 12 LIM_DEC220 MIXOUT OSCIN 4 3 OSCOUT 10 QUADIN 1 AUDIOOU T 8 7 AUDIO_FEED 15 GN D 18 IFAMPI N 16 IFAMPOUT IFAMP_DEC119 17 IFAMP_DEC2 14 SA616U5 1 680 R78 R77 1% 8.2KR67 5V IF_BAND_SEL 20K R76 1% 12K 0.1uF 36pF 1% C82 5.1KC68 R54R66 20K R63 C72 0.1uF 455KHz 32 1 39K 45B02Y70 5V IF_RSSI SH50 SHIELD 1 R55 330C64 0.1uF 390 R72 39K R65 3.3K R61 100K R62 TC7W04F U52-335 IF_5 V C92 0.1uF 51 R90 BW_SE L 5V IF_IN RSSI DEMOD 47pF C61 47pF C74 Figure 12-5. UHF (403-440 MHz) Receiver Back End Schematic Diagram (8486635Z03-O)
12-8UHF (403-440 MHz) Schematic Diagrams, Overlays, and Parts Lists (8486635Z03-O)June, 200568810309N62-C 100 C2020V 3V 0V TX: 3V RX: 0V 14R06 150kNU R202 C206 D201 R206 Y202 C203 1SV2324.5V UNLOCK: 0V 3V Y2012.7pF 45J68LOCK: 3V NU NU NU NU NU 47k3.2V to 4.5V C201 Reference Oscillator NU 0.01uF 62pF NU 220pFCrystal UHF R1 Synthesizer TCXOC211 0.1uF NC1000pFC231 NC 0.1uFC216 FN_PRESC 22 R220 R246 100K 1000pF C227R245 1.5K NC R244 51 470pFC208R221 22 C204 470pF C201 220pF C2070.1uF C232 470pFFN_16_8 C217 1000pF0888600M25 C244 .01uF FN_SYNTH_CS 0.1uF C228 C205 NU GND2 GND14 OUT 3 IN1 C202NC 16.8MHz14R06Y201 VMULT4 VRO 13 25 WARP 23 XTAL124 XTAL2 62pF 1% SFOUT 37 TEST138 TEST2 21 VBPASS 47 VCP 15 VMULT114 VMULT212 VMULT311 PREIN 33 PRE_GN D 34 PRE_VDD 35 PVREF 18 REFSEL 27 SFBASE 26 SFCAP 30 SFIN28 4 10 MODIN 41 MODOUT 17 NC1 29 NC2 31 NC3 44 PD_GND PD_VDD 5 32 CLK 7 D ATA 6 DGND 36 DVDD 19 FREFOUT45 IADAPT16 INDMULT 43 IOUT LOCK AUX22 AUX33 AUX4 20 AVDD 40 BIAS1 39 BIAS2 42 CCOMP 9 CEX 846 ADAPTSW 22 AGND 48 AUX11 1 63A27 U201 FN_MOD TP200 C223 .01uF.01uFTP240 1 C213 L211 390nH NU R212 0R206 1 K1 2 K2 3 K3 6 A15 A24 A3 C221 D221 .01uF 2.2uF C215 2.2uFFN_V_SF C218 C230 2.2uF C240 NC FN_VCO_MOD 1.3pFNC NC C203 3.7% 2.7pF NC C214 1000pF FN_5VFN_LOCK NC NCFN_V_STEER 100 R205 .01uFC222 FN_CLK C224 .01uF C233 0.1uFC243 C245 4.7uF NC NC NC 1uF 1SH201 SHIELD 1 K1 1K2 2K3 3 SH200 SHIELD 6 A15 A24 A3 D220 FN_DATA R227 39K 100pF C241 R243 820 R230 24KR247 22K 470pF C219 C210NC NC 0.1uF FN_3V 100 R223 NC NC 150KR202 OUT 3VCC4 VCON1 C209 470pF 16.8MHz45J68Y202 NU GND 2 10uFC226 D201C220 22pF 5V C212 2.2uF 10uF NC 5V NC C225 NUFN_TRBV_SF V_STEER 5VC206LOCK PRESC 16_8_MHZ 3V SPI_DATA_OUT MOD_IN SYNTH_CS SPI_CLKVCO_MOD TRB Figure 12-6. UHF (403-440 MHz) Synthesizer Schematic Diagram (8486635Z03-O)