Mitsubishi Xl5980lu Lcd Projector User Manual

							EN – 11
ENGLISH
For using the COMPUTER/COMPONENT VIDEO INPUT 2 (Mini D-SUB 15P) terminals
REMOTE
INREMOTE
OUTINPUT 1
INPUT 2R/PRB/PBG/Y H/HVV
AUDIO
IN
AUDIO
OUTY
CRS-232C RS-232C/MOUSEUSB
S-VIDEO
VIDEO
2
VIDEO
1
L
AUDIO
R MAIN
AC INTo COMPUTER IN
 (Mini D-SUB 15P)
To COMPUTER OUTPUT
When outputting to both the computes monitor and the projector. PC audio cable (option)
RGB cable for PC (option)
Computer
To COMPUTER AUDIO IN
To PC audio 
output
AUDIO OUT
MONITOR OUTPUT
To monitor port
For using the COMPUTER/COMPONENT VIDEO INPUT 1 (BNC) terminals
REMOTE
INREMOTE
OUTINPUT 1
INPUT 2R/PRB/PBG/Y H/HVV
AUDIO
IN
AUDIO
OUTY
CRS-232C RS-232C/MOUSEUSB
S-VIDEO
VIDEO
2
VIDEO
1
L
AUDIO
R MAIN
AC IN
computer
B/PB
G/Y
V H/H
V
R/PR
Mini D-SUB 15pin-BNC 
conversion cable (optional)
to COMPUTER AUDIO IN
to PC audio 
outputPC audio cable (option)
AUDIO OUTMONITOR OUTPUTto monitor
port
Projector + Computer
Important:
•When you use a longer RGB cable instead of the provided cable, the picture quality may deteriorate.
•Some computers may require additional connectors or analog RGB output adapters to be connected with this
projector. Contact your dealer for further information.
•This projector uses a stereo pin jack for its audio input. Check the type of the audio output terminal of the
connected computer and prepare a proper cable for connection. Some computers may not have the audio
output terminal.
For Macintosh
•If your Macintosh has no video port, a monitor output adapter is required. Contact your dealer for further
information.
•Some Macintoshes may require a MAC adapter for the RGB cable for connection with this projector. Contact
your dealer for further information.
About DDC
The COMPUTER/COMPONENT VIDEO INPUT 2 terminal of this projector complies with the DDC1/2B stan-
dard.
When a computer supporting this standard is connected to this terminal, the computer will automatically load
the information from this projector and prepare for output of appropriate images.
•After connecting a computer supporting this standard to this terminal, turn on the projector’s main power
switch first, and then boot up the computer.
•You may need to install the DDC driver, depending on the computer you use. In this case, you need to down-
load the driver from our Web site. Contact your dealer or Mitsubishi sales office for further information. 
						

							EN – 12
Adjustment foot
screen
Preparing the projector for operation
Getting ready for projection
1. Attach the provided power cord to the projector.
2. Plug the power cord in the wall outlet.
3. Remove the lens cap.
Warning:
•Do not look into the lens directly when the projec-
tor is “ON.”
•The lens cap is for protecting the lens. If you leave
the lens cap on the lens with the projector turned
on, it may be deformed. Remove the lens cap when
you turn on the projector.
•The power cords for use in the U.S. and Europe
are included with this projector. Use the appropri-
ate one for your country.
•This projector uses the power plug of three-pin
grounding type. Do not take away the grounding
pin from the power plug. If the power plug doesn’t
fit your wall outlet, ask an electrician to change
the wall outlet.
•The provided power cord for the U.S. is rated at
120 V. Never connect this cord to any outlet or
power supply using other voltages or frequencies
than rated. If you use a power supply using other
voltage than rated, prepare an appropriate power
cord separately.
•Use 100-240 V AC 50/60 Hz to prevent fire or
electric shock.
•Do not place any objects on the power cord and
keep the projector away from heat sources to
prevent damage to the power cord. If the power
cord gets damaged, contact your dealer for re-
placement because it may cause fire or electric
shock.
•Do not modify or alter the power cord. If the
power cord is modified or altered, it may cause fire
or electric shock.
Caution:
•Plug in the power cord firmly, and unplug it by
holding and pulling out the power plug, not by
pulling the power cord.
•Do not plug in or out the power cord with your
hand wet. It may cause electric shock.
Adjusting the angle of projection
For the best projection, project the image on a flat
screen installed at 90 degrees to the floor. If neces-
sary, tilt the projector using the two adjustment feet
on the bottom of the projector.
1. Rotate the adjustment feet for fine adjustment.
After using the projector
2. Put the adjustment feet back into the projector by
rotating the adjustment feet.
•Install the screen on a flat wall at 90 degrees to
the floor.
•Position the projector so that it projects an image
filling the screen as illustrated on page 9.
•Keep an appropriate distance from the projector to
the screen according to the screen size chart on
page 9.
•The image becomes trapezoid shape when the
screen or project is not level. Use KEYSTONE
button and + or - buttons to adjust, however, the
circumference of the image may not be focused.
Important:
•Slanting the projector more than ±15˚ (right and
left  or front and rear) may cause trouble or explo-
sion of the lamp. You can tilt the projector up to 7
degrees using the adjustment feet only.
•The image may not be projected in a shape of a
regular rectangle or with its aspect ratio of 4:3,
depending on the installation conditions of the
projector and the screen.
•When the keystone adjustment is carried out, the
adjustment value is indicated.  Note that this
value doesn’t mean a projection angle.
•The allowable range of the adjustment value in
the keystone adjustment will vary depending on
the installation conditions.
Adjustment foot 
						

							EN – 13
ENGLISH
To operate projector power ON
4.Press the ZOOM/FOCUS button to FOCUS. “FO-
CUS” will appear on the display.
5. Adjust with the + or - button to get a fine picture.
6.  Select the desired external input source by using
the COMPUTER 1,2 or VIDEO1,2 button on the re-
mote control or the SOURCE button on the control
panel.
•Pressing the SOURCE button on the control panel
repeatedly will select VIDEO 1, VIDEO 2, COM-
PUTER 1 and COMPUTER 2.
•The projector automatically selects the appropriate
signal format. The selected signal format is dis-
played on the screen.
•The COMPUTER, VIDEO or SOURCE buttons do
not work when MENU is displayed. At this time,
the prohibition mark (
) appears on the screen.
•When selecting the COMPUTER input, the image
may  flicker.  Press the $ or % button to adjust the
image.
•The intensity of the lamp will be STANDARD for 2
minutes regardless of the setting of the LAMP
MODE when the lamp turns on.
7.   Press the ZOOM/FOCUS button to ZOOM. “ZOOM”
will appear on the display.
8. Adjust with the + or - button to get an approximate
size.
9.   Press the LENS SHIFT button. “LENS SHIFT”
will appear on the display.
10.Adjust with the {, }, $ or %  button to get an
approximate lens position.
•If necessary, adjust focus, zoom and lens shift again.
•Focus, zoom and lens shift adjustment is possible
in the normal picture mode only. In PinP or EXPAND
mode, the adjustment is prohibited. 1. Turn on the equipment connected to the projector.
2.Put the projector into standby mode by pressing the
main power switch. The POWER indicator lights up
red.
3. Turn the projector on by pressing the POWER but-
ton. The light source lamp starts warming up, even-
tually turning completely on.
•The lamp may take about a minute to light up.
•The lamp occasionally fails to light up. Try to light
up the lamp again after a few minutes.
•If the projector has not cooled down completely
since the last turning-off, the fan may start
rotating when the main power switch is turned
on and the POWER button may not function.
Press the POWER button to light up the lamp
after the fan stops.
conditionindicator
LAMPPOWER
stand-by
-red
when light source lamp is ongreen
green
light source lamp held off temporarilyred-
Important:
•A darkened image may be seen right after pressing
the POWER button due to warming up of this pro-
jector. While warming up, no other commands can
be accepted.
•After the power is turned on or the LAMP MODE is
changed, the screen may flicker before the lamp op-
eration becomes stable. This is due to the charac-
teristics of the lamp, not a failure of the lamp.
•When the lamp indicator is blinking red, the ser-
vice life of the lamp is about to end.  Replace the
lamp. See pages 22 and 26.
•The picture might not be of optimum performance
in extreme hot or cold conditions. (The projector is
not malfunctioning.)
COMPUTER
VIDEO KEYSTONE
VOLUME
LASEREXPAND
MENU R-CLICK ENTER
P in PSTILL
MUTE
LENS SHIFT16 : 9
12
12
ZOOM/FOCUS AUTOPOSITION
AUTO POSITION 
button
AUTO POSITION 
button
MUTE buttonMUTE button
2, 13
6, 85, 73, 11, 12
4
4
10
9
9
6, 85, 7
3, 11, 12
10
REMOTE
INREMOTE
OUTINPUT 1
INPUT 2R/PRB/PBG/Y H/HVV
AUDIO
IN
AUDIO
OUTY
CRS-232C RS-232C/MOUSEUSB
S-VIDEO
VIDEO
2
VIDEO
1
L
AUDIO
R MAIN
AC IN
LAMP
VOLUME
ZOOM/
FOCUSKEYSTONE
TEMP
SOURCEMUTE AUTO  POSITION LENS SHIFT
MENUENTER
POWER 
						

							EN – 14
VOLUME     15
To operate projector power ON (Continue)
Turning off the projector
Use the following procedure to turn off the power.
Don’t turn off the power by switching off the main
power switch or disconnecting the power plug be-
cause these methods may cause deterioration
in the lamp’s performance or failure in the product.
11.Press the POWER button.
The message “POWER OFF? YES : PRESS AGAIN”
appears on the screen.
•To exit this mode, press any button except the POWER
button. (Some buttons on the remote control don’t
work for exit from this mode.)
12. Press the POWER button again.
The light source lamp will go out. Though the light source
lamp will go out at this second press of the POWER but-
ton, the exhaust fan continues to operate for another 120
seconds to cool down the lamp and LCD panel. In this
case, the lamp indicator will go out.
13. Turn off the main power switch, and the POWER indi-
cator will go out.
•In cases where the main power switch is accidentally
turned off when either the intake/exhaust fan or the
power source lamp is in operation, allow the unit to
cool down for 10 minutes with the power turned off.
Repeat step 3 when turning on the power source lamp.
If the lamp does not turn on immediately, repeat this
step two or three times. Replace the lamp if it should
still fail to turn on.
AUTO POSITION button
When the image isn’t projected in the right position with
COMPUTER selected as the image source, follow the
steps below.
1. Project a bright image such as the “Trash” window on
the full screen.
2. When the screen saver is running, turn it off.
3. Press the AUTO POSITION button.
•If the image is still not in the right position, adjust the
image position using the SIGNAL menu.
Volume from the speaker
Press the volume + or – button to change the volume from
the speaker.
The volume control bar will appear on the screen.
•The volume control bar will disappear about 4 seconds
after releasing the volume buttons.
•The volume buttons don’t work while the MENU
selection bar or the MENU is being displayed.
•When a high-level audio signal, such as a DVD audio
signal, is supplied to the COMPUTER AUDIO IN
terminal, the output from the speaker may be dis-
torted.AV mute
The image and audio signals are temporarily muted by
pressing the MUTE button. To bring them back to their
normal level, press the MUTE button again.
•The audio from the AUDIO OUT jack is also muted by
pressing the MUTE button.
•If the MUTE MODE in the INSTALLATION menu is
set to LOGO, the splash screen will appear by pressing
the MUTE button.
Please contact your dealer or Mitsubishi sales office for
further information.
•You can alter the splash screen freely. Please contact
your dealer or Mitsubishi sales office for further
information.
•The lamp mode becomes “LOW” during muting.
Therefore, the display of LOGO will darken, which
isn’t a failure.
•Muting will be cancelled in 3 hours automatically for
the purpose of protecting devices. However, when the
mute mode has been set to “LOGO,” muting won’t be
cancelled.
ANAMORPHIC mode
When playing DVD discs containing data of letterboxed
image, press the 16:9 button. Exit the ANAMORPHIC
mode, by pressing the 16:9 button again.
Caution:
•When you have finished using this projector, wait 120
seconds for the exhaust fans to stop. Then turn off the
main switch and unplug the power cord from the wall
outlet, for safety purposes.
•The lamp cannot be turned on again for 60 seconds after
it was turned off for precautionary purposes. It will take
another 60 seconds before the lamp indicator goes off. If
you want to turn on the projector again, wait until the
indicator is off, and then press the POWER button.
•The exhaust fan rotates faster as the temperature around
the projector rises.
•When the temperature around the projector rises too
high, the sign  “TEMPERATURE!!” blinks red on the
screen. If the temperature stays too high, the lamp will
be go out automatically. 
						

							EN – 15
ENGLISH
Basic operation
Several settings can be adjusted using Menu.
EXAMPLE: Auto power off time setting
1.  Press the MENU button.
2.  Press the $ or % button to select the INSTALLA-
TION menu.
3.  Press the ENTER button (or } button).4.  Press the { or } button to select AUTO POWER
OFF.
5.  Press the $ or % button to adjust auto power off
time.
6.  Exit the menu system by pressing the MENU but-
ton several times.
•If the menu operation is not working, press the
RESET button on the terminal board using a suit-
able sharp object, push gently.
•The settings with 
 mark, you should press the
ENTER button after selecting.
Menu operation
IMAGE
XGA60opt.
INSTALLATION
XGA60opt.
ON AUTO POWER 
ON
OFF
AUTO POWER 
OFFOFF
ON
INSTALLATION
BLUE BACK COLOR
XGA60
SPLASH SCREEN
opt.
AUTO POWER 
ON
OFF
AUTO POWER 
OFFOFF
AUTO POWER 
ON
30 min
AUTO POWER 
OFFOFF
IMAGE CONTRAST± 30BRIGHTNESS
COLOR MATRIX± 30sRGB ON , OFF
STANDARDHIGHLOWUSER    
COLOR TEMP.
COLOR± 10TINT± 10SHARPNESS± 10GAMMA MODE AUTO, DYNAMIC, STANDARD, THEATERCONTRAST R± 30
CONTRAST B± 30BRIGHTNESS R± 30BRIGHTNESS B
(Displays only when the source is selected to VIDEO)
(Displays only when the source is selected to VIDEO)± 30
EXPAND MODE 1 - 4FRAME POSI. 1 - 5
INSTALLATION
IMAGE REVERSE OFF, MIRROR, INVERT, MIRROR INVERT
AUTO POWER ON
ON , OFF
RESET ALL OK 
AUTO POWER OFFON , OFF
FEATURE MENU POSITION 1 (Upper left), 2(Lower right)
LENS SHIFT USER    
SPLASH SCREEN
BLACK, LOGOMUTE MODEBLUE, LOGO, BLACKBACK COLOR
STANDARD, LOWLAMP MODE
OFF, CENTER, UPPER, LOWER  ANAMORPHICON , OFF3D CineView
ON , OFFSCART INPUTVIDEO SIGNAL AUTO , NTSC , PAL , SECAM , 4.43NTSC , PAL-M , PAL-N , PAL-60
LANGUAGE, English, Español, Deutsch, Français, Italiano,        ,          ,             ,    
VIDEO
YELLOW± 30RED± 30
BLUE± 30CYAN± 30GREEN± 30
MAGENTA± 30SATURATION± 5RGB-TINT± 15
COMPUTER USEROFF
SIGNALMEMORY CALL AUTO, USER1, USER2HORIZ.POSITION 0 - 999VERT.POSITION 0 - 999FINE SYNC. 0 - 39TRACKING
USER0 - 9999CLAMP POSITION0 - +63CLAMP WIDTH 1 - 63HORIZ. PIXELS 0 - 9999VERT. LINES 0 - 9999
SHUTTER(L)
0 - 383SHUTTER(U)
0 - 383
SHUTTER(RS)
0 - 510SHUTTER(LS)
0 - 510
VERT. SYNC.
AUTO, ON, OFF
MEMORIZE*5
*3 *3
*4
*3
*3
*3
*3
*3
*3
*3 *5
*5
HOLD AUTO
USER1, USER2DELETEUSER1, USER2DEFAULTON
BEGIN -1 - -99END 1 - 99
LOCK ON, OFFRESET OK
OFF
COMPUTER INPUTRGB, YCBCR / YPBPR
*5
*5
*5
*5
OFF,  5,  10,  15,  30,  60 min
(The item can not be selected when 
the source is selected to COMPUTER) *1
*1
*2
* 1: The item can not be selected when the sRGB is set to ON.
* 2: The item can not be selected with certain signals.
* 3: The item can not be selected when the selected source 
       is VIDEO or S-VIDEO.
* 4: The item can be selected only when the selected source 
       is VIDEO or S-VIDEO or the inputted signal is TV50 or TV60.
* 5: Setting range is different with certain signals. 
						

							EN – 16
IMAGE REVERSE
ON AUTO POWER 
ON
OFF
AUTO POWER 
OFFOFF
ON
INSTALLATION
BLUE
OFF
BACK COLOR
USER BLACK
XGA60
LENS SHIFT
SPLASH SCREEN
MUTE MODE
STANDARD
opt.
LAMP MODE
1 IMAGE
CONTRAST.........Adjusts the picture contrast. The contrast becomes higher as the
number increases.
BRIGHTNESS.....Adjusts the image brightness. The image becomes brighter as
the number increases.
sRGB....................Select ON to display an image emphasizing on the color
reproducibility.
•When sRGB is ON, COLOR MATRIX, COLOR TEMP.  and
GAMMA COLLECTION can’t be ad justed.
COLOR MATRIX.........Adjusts the color balance in each color of the image. See page 18.
COLOR TEMP.....Adjusts the color temperature. See page 19.
COLOR................Adjusts the color intensity of the image. (Available only when
VIDEO is selected as the source.)
TINT....................Adjusts the color balance of the image. The color balance of the
image shifts green as the number increases and shifts to purple
as the number decreases. (Available only when VIDEO is
selected as the source.)
•When the TV50 (PAL, SECAM) signal is inputted, TINT can’t be adjusted.
SHARPNESS.......Adjusts the image sharpness. The image sharpness rises as the number increases.
GAMMA MODE ... When AUTO is selected, the appropriate gamma mode is automatically selected depending on the
input signal. For normal use, select  AUTO. Select DYNAMIC for computer sources. Select
STANDARD for  sport scenes and video sources. Select THEATER for projecting film sources.
2 INSTALLATION
AUTO POWER ON......Select ON to boot up the projector automatically by turning on
an externally connected power switch such as a breaker even
when the main power switch of the projector is off. Use this
setting when the projector is hanging from the ceiling.
•The projector will be in the stand-by mode when the lamp
is off.  Use the remote control to turn on the lamp.
AUTO POWER OFF....Set the time elapsed before the projector enters into the stand-by
mode when there is no signal inputted from the selected source.
SPLASH SCREEN.......Select ON to display the splash screen when the power is turned
ON.
•The splash screen can be changed. For more details, please
consult your dealer.
BACK COLOR......Use to select the background, BLUE, BLACK or LOGO, which
will be displayed when there is no signal inputted from the selected source. When the LOGO is
selected, the splash screen will be displayed.
MUTE MODE...... Use to select the background, BLACK or LOGO, which will be displayed when the MUTE button is
pressed. When the LOGO is selected, the splash screen will be displayed.
LAMP MODE.......Use to change the brightness of the lamp. When LOW is selected, the image will become darker,
though the power will be saved, operating sound will be reduced.
 •The intensity of the lamp will be STANDARD for 2 minutes regardless of the setting of the LAMP
MODE when the lamp turns on.
•When the LAMP MODE is changed, the screen may flicker. This is not a failure of the lamp.
IMAGE REVERSE......Use to reverse or invert the projected image. Select MIRROR in rear projection. Select MIRROR,
INVERT in rear projection with the projector hanging from the ceiling.
LENS SHIFT........ To enter the LENS SHIFT setting mode, press the ENTER button. For lock the lens position, set
LOCK to ON. For reset the lens position, select RESET and press the ENTER button.
•When no signal is supplied for 6 hours with BACK COLOR set to BLACK, it changes to BLUE
automatically for the purpose of protecting the projector.
•When you continue projection for a long time with BACK COLOR or MUTE set to LOGO, an after-image
may persist on the screen.
•When the signal is lost during muting with MUTE set to LOGO, AUTO POWER OFF is ignored even
though it is active.
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
COMPUTEROFF
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE COLOR MATRIX sRGB
opt.
Menu operation (continued) 
						

							EN – 17
ENGLISH
3 FEATURE
MENU POSITION.......Use to select the position of the menu on the screen,   (upper
left) or 
 (lower right).
EXPAND MODE .. Select the mode for enlarging screen. See page 20.
FRAME POSI.......Sets the position of sub screen. See page 20.
VIDEO SIGNAL ...When AUTO is selected, the appropriate video format is
automatically selected depending on the input signal. If the
image isn’t displayed correctly, select the desired video format
manually.
SCART INPUT.....Select ON when connecting with a device equipped with the
SCART terminal that can output RGB signal. SCART terminal
is used mainly in Europe. Select OFF normally.
ANAMORPHIC....Select the desired position, UPPER, CENTER or LOWER when
playing DVD discs containing data of letterboxed images.
3D Cine View........ Select ON for high quality video image. Select ON normally.
LANGUAGE........Use to select the language used in the menus. (
 / English / Español / Deutsch / Français / Italiano
/ 
/  /  / )
RESET ALL.........Use to reset the MENU settings (except LANGUAGE).
•When SCART is set to ON, nothing is output to the external monitor.
•When SCART is set to ON, normal computer signals are not projected.
•Use SCART-BNC (or SCART-Mini D-SUB 15P) cable (option), when connecting with AV device equipped with
the SCART terminal.
•Some AV devices equipped with the SCART terminal may not be compatible with the projector.
•When VIDEO SIGNAL is set to AUTO, the image may not be projected with correct colors. Change the setting of
VIDEO SIGNAL depending on the input signal in such cases.
•When 3D Cine View is switched from OFF to ON, you can check the motion detection operation about three seconds.
The buttons on the remote control don’t work during this period, which isn’t a failure.
•When the LANGUAGE in FEATURE menu is set to English and NTSC video format is selected, the brightness is
decreased 15 points by set-up cancel function for U.S. (The indicated value is not changed.) The image becomes darker,
but this is not a failure of the projector.
4 SIGNAL
MEMORY CALL..........Use to select AUTO, USER 1 or USER 2. See page 18.
HORIZ. POSITION......Use to adjust the horizontal position of the image.VERT. POSITION........Use to adjust the vertical position of the image.
FINE SYNC..........Use to synchronize the projector with PC input signals so that
the image is not blurred.
TRACKING..........Use to avoid image noise such as wide stripes.
COMPUTER INPUT......The unit adjusts itself automatically when connected to a DVD
player with a component video output (Y, CB, CR). In the case the
projector is connected to equipment that includes RGB output
terminal, adjust to RGB mode.
HOLD..................Adjusts the image when flagging occurs near the top of the
screen.
5 SIGNAL  - USER (Normally, there is no need for adjustments.)
CLAMP POSITION/
CLAMP WIDTH..........
If you use something similar, the brighter colors of the projected
image may become blurred. In this case, adjust CLAMP POSITION
or CLAMP WIDTH.
HORIZ.PIXELS.... Use to adjust the width of the image.  The image size grows wider as
the number increases.  (Adjust to the horizontal pixels of the input
signal for normal setting.)
VERT.LINES.......Use to adjust the height of the image.  The image size grows higher
as the number increases.  (Adjust to the vertical lines of the input
signal for normal setting.)
VERT.SYNC.........Use to adjust the image when its motion does not run smoothly.
Select AUTO for normal setting.
SHUTTER(U).......Use to adjust the image when the noise etc. appears on top part of
image.
SHUTTER(L).......Use to adjust the image when the noise etc. appears on bottom part of image.
SHUTTER(LS).....Use to adjust the image when the noise etc. appears on left side of image.
SHUTTER(RS).....Use to adjust the image when the noise etc. appears on right side of image.
•When the setting of the SIGNAL-USER menu is changed, the image may not be displayed correctly. In this case, select
DEFAULT 
 in the SIGNAL menu, and press the ENTER button.
FEATURE
OFF
ON
OFF
XGA60
AUTO
3D CineView
English
opt.
MENU POSITION
EXPAND MODE
FRAME POSI.
A A
AA
VIDEO SIGNAL?
ANAMORPHIC
RESET ALL LANGUAGE
AË
OK
1.
1.
3.
SCART INPUT
CLAMP POSITION
SIGNAL-USER
0
CLAMP WIDTH 1
HORIZ. PIXELS 0
SHUTTER(RS) 0 VERT. LINES 0
VERT. SYNC. AUTO
SHUTTER(LS) 0 SHUTTER(L) 0 SHUTTER(U) 0
R G BR G B
A
UMEMORY CALL
SIGNAL
AUTO
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER INPUT RGB FINE SYNC. 0
HOLD AUTO
USER MEMORIZEDELETE DEFAULT
XGA60opt. 
						

							EN – 18
User memory for signal setting
This projector can memorize the maximum of 2 signal
menu settings.
Memorizing the setting
1.  Select MEMORIZE 
 in the SIGNAL menu, and press
the ENTER button.
2.  Press the $ or % button to select the memory which you
wish to record (USER 1 or USER 2).
3.  Press the ENTER button.
•Any buttons are ineffective about 3 seconds of
recording setting.  Wait for recording to have been
completed before operating the buttons.
Select the user setting
Select MEMORY CALL in SIGNAL menu, and press the
$ or % button to select the memory (USER 1 or USER 2).
Reset the recorded setting
1.  Select DELETE 
 in the SIGNAL menu, and press the
ENTER button.
2.  Press the $ or % button to select the memory which you
wish to reset (USER 1 or USER 2).
3.  Press the ENTER button.
The recorded setting will be reset.
•Any buttons are ineffective about 3 seconds of
resetting the recorded setting.  Wait for resetting to
have been completed before operating the buttons.
Adjusting the image
You can adjust the picture by using the IMAGE menu.
To control the level of white-to-black in the image :
Adjust CONTRAST in IMAGE menu.  Press the %
button to increase the contrast and the $ button to
reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in IMAGE menu.  Press the %
button to lighten the image and the $ button to
darken the image.
To determine the intensity of the color :
Adjust COLOR in IMAGE menu.  Press the %
button to increase the amount of color in the image
and the $ button to decrease it.
To adjust the red-green color balance of the image :
Adjust TINT in IMAGE menu.  Press the % button
to increase the amount of green in the image and the
$ button to increase the amount of red in the image.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in IMAGE menu.  Press the %
button to make the picture seem sharper and the $
button to make it softer.
Picture adjustment
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
AUTO0
XGA60
COMPUTEROFF
TINT
0SHARPNESS
COLOR TEMP.
GAMMA MODE COLOR MATRIX sRGB
opt.
Color matrix
This feature adjusts the color balance in each color of
RGB (Red, Green, Blue), and their neutral colors
(yellow, cyan, magenta) by using Color correction
adjustment. Use Color correct adjustment when
enphasizing a specific color, or when only a certain
color balance is not correctly adjusted.
1.  Select COLOR MATRIX in IMAGE menu.
2.  Press the $ or % button to select USER 
.
3.  Press the ENTER button.
4.  Press the { or } button to select the desired color.
•If you wish to adjust the color intensity of the
image, select SATURATION.
•If you wish to adjust the all color balance of the
image, select RGB-TINT.
5.  Press the $ or % button to adjust the color balance
of the color.
6. Repeat steps 4 and 5 for more adjustments.
7. Exit the menu system by pressing the MENU but-
ton several times.
•When using the setting which has been already
prepared, select desired position VIDEO or
COMPUTER in step 2.  When the source is selected
to VIDEO or S-VIDEO, VIDEO will be selected
automatically. When the source is selected to
COMPUTER, COMPUTER will be selected
automatically.
•When not using Color matrix adjustment, select
OFF in step 2.
COLOR MATRIX
RED 0
0
0
RGB-TINT 0
0
0
GREEN
BLUE
YELLOW
CYAN
MAGENTA 0
SATURATION0 
						

							EN – 19
ENGLISH
CONTRAST R
COLOR TEMP.-USER
0
CONTRAST B 0
BRIGHTNESS R 0
BRIGHTNESS B 0
Color temperature
1.  Select COLOR TEMP in IMAGE menu.
2.  Press the $ or % button to select USER 
.
3.  Press the ENTER button.
4.  Press the { or } button to select the desired item.
5.  Press the $ or % button to adjust the item.
6. Repeat steps 4 and 5 for more adjustments.
7. Exit the menu system by pressing the MENU but-
ton several times.
Adjustment from personal computer
Although this projector sets proper signal systems
automatically for the image signal from personal
computers, it cannot be applied to some of personal
computers.  In this case, press the AUTO POSITION
button.  If the images are still not projected correctly,
use the MENU display to adjust the projected im-
ages.
Image moved to right or left :
Adjust HORIZ. POSITION in SIGNAL menu.  Press
the % button to move the image to left.  Press the $
button to move the image to right.
Image moved to up or down :
Adjust VERT. POSITION in SIGNAL menu.  Press
the % button to move the image to upward.  Press
the $ button to move the image to down. About color temperature
There are different kinds of white color. Color temperature is
a way to show the differences. The white, which temperature
is low, becomes reddish white. When the color temperature is
higher, the white becomes more bluish. This projector sets
this color temperature by changing the numbers of contrast
blue and red.
To set the color temperature high:
Set the contrast B (Blue) number high, and the contrast R
(Red) number low.
To set the color temperature low:
Set the contrast B (Blue) number low, and the contrast R
(Red) number high.
R G BR G B
A
UMEMORY CALL
SIGNAL
AUTO
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER INPUT RGB FINE SYNC. 0
HOLD AUTO
USER MEMORIZEDELETE DEFAULT
XGA60opt.
CLAMP POSITION
SIGNAL-USER
0
CLAMP WIDTH 1
HORIZ. PIXELS 0
SHUTTER(RS) 0 VERT. LINES 0
VERT. SYNC. AUTO
SHUTTER(LS) 0 SHUTTER(L) 0 SHUTTER(U) 0
Image flickers / Image is out of focus :
Adjust FINE SYNC. in SIGNAL menu.
A solid black or solid white appears in the image :
Adjust CLAMP POSITION or CLAMP WIDTH of
each menu in SIGNAL - USER menu.
Noise appears on right or left side of image :
Adjust SHUTTER (LS), SHUTTER (RS) or HORIZ.
PIXELS  of the menu in SIGNAL - USER menu.
Noise appears on top or bottom part of image :
Adjust SHUTTER (U), SHUTTER (L) or VERT.
LINES of the menu in SIGNAL - USER menu.
Top part of image curves :
Change the setting of HOLD in SIGNAL menu.
Select ON 
, press the ENTER button and adjust
BEGIN or END for image which top part is the least
curved.
Image does not move naturally :
Adjust VERT. SYNC. of the menu in SIGNAL -
USER menu.  Select AUTO for normal setting.
curved.  Select AUTO for normal setting.
•Do not change each menu setting in USER menu
for normal setting.
Simple adjustment method
1. Select HORIZ. POSITION in SIGNAL menu.
2. Press the$ or % button to adjust the horizontal
start position (the left side of image).
3. Select TRACKING in SIGNAL menu.
4. Press the$ or % button to adjust the horizontal
end position (the right side of image).
5. Repeat steps 1 to 4 for fine adjustment.
6. Select VERT. POSITION in SIGNAL menu.
7. Press the$ or % button to adjust the vertical
start position (the top end of image). 
						

							EN – 20
Advanced features for presentation
Expand
By pressing the EXPAND button on the remote con-
trol, you can magnify the detailed image of the picture.
You can also view the screen displaying the picture as
its original size (native resolution display).
Setting the Expand mode
1. Press the MENU button.
2. Press the $ or % to select the FEATURE menu.
3. Press the ENTER button.
4.Press the  { or } button to select EXPAND MODE
or FRAME POSI.
5.Press the $ or % to set the EXPAND MODE or
FRAME POSI.
6.Press the MENU button twice to exit the menu sys-
tem.REAL screen display
•During REAL mode, Press the $ or % buttons
for fine adjustment.
•During REAL mode, the { and } buttons are
not working. At this time, the prohibition mark
(
) appeares on the screen.
•The expanding rate cannot be changed by press-
ing either the + or - button.
Picture in Picture (PinP)
One of the special features of this unit is the picture-
in-picture (PinP) mode. PinP allows you to view differ-
ent sources at the same time.
Using the PinP mode
1. Press the PinP button on the remote control.
•When the image from VIDEO IN or S-VIDEO
IN terminal is displayed on the screen, the im-
age from COMPUTER IN terminal is displayed
as sub-image.
•When the image from COMPUTER IN terminal
is displayed on the screen, the image from VIDEO
IN or S-VIDEO IN terminal is displayed as sub-
image.
2.If necessary, select the desired external input source
of the image by using the VIDEO or COMPUTER
button.
To switch Main image and Sub image
3. Press the { or } buttons on the remote control.
To change frame position
4. Press the $ or % buttons on the remote control.
5. Press the PinP button on the remote control.
The sub image will be disappear.
•Adjusting contrast, brightness, tint or color is not
available in PinP mode.
•In PinP mode, both Main image and Sub image
are displayed with their frames skipped.
•In PinP mode, the audio of the Main image is
outputted.
•In PinP mode, the images may not move smoothly.
•The PinP mode may not function depending on the
input signal. For more details, refer to page 29.
•The UXGA signal isn’t displayed as a sub image.
Still
How to stop the picture temporarily (still picture).
1. Press the STILL button on the remote control.
The picture will freeze temporarily.
To resume picture activity.
2. Press the STILL button on the remote control again.
Normal
imageNative resolution
 display Zooming
image
(EXPAND MODE 1)
Zooming
imageNormal
image
(EXPAND MODE 2)
Zooming
image
(EXPAND MODE 3) (EXPAND MODE 4)EXPAND MODE 
(FRAME POSI.
 1~4)(FRAME POSI. 5)
12
3 4
Main
imageSub
image
FRAME POSI.
Using the Expand mode
1. Press the EXPAND button.
•You can magnify different areas of the active pic-
ture by pressing the {, }, $, % button.
•You can change the magnification of the zoomed area
by pressing the + or - button.
2.Press the EXPAND button twice on the remote con-
trol.
The normal screen display will appear on the screen.
•Display enlargement does not work with
video input or S-video input.
•In EXPAND mode, you cannot adjust the zoom/fo-
cus and the volume.
•The Expand mode may not function depending on
the input signal. For more details, refer to page
29.
(FRAME POSI.
 1~4)(FRAME POSI. 5)
12
3 4
Main
imageSub
image
FRAME POSI.