Mitsubishi Xl5980lu Lcd Projector User Manual

							EN – 1
ENGLISH
XL5980
LCD PROJECTOR
MODEL
XL5980U
XL5980LU
User Manual
This User Manual is important to you.
Please read it before using your projector. 
						

							EN – 2
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the litera-
ture accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE IN-
STALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If you
use another power-supply cord, it may cause interfer-
ence with radio and television reception.
Use the attached RGB cable, RS-232C cable with this
equipment so as to keep interference within the limit
of a FCC Class A device.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS
WHEN PROJECTOR IS IN THE POWER ON
MODE.
CAUTION
Not for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/
Data Processing Equipment, ANSI/NFPA 75.
The attached power cords are to be used exclusively
for this product. Never use them for other products.When using the projector in Europe
COMPLIANCE NOTICE
This Projector complies with the requirements of the
EC Directive 89/336/EEC “EMC Directive” as
amended by Directive 92/31/EEC and 93/68/EEC,
and 73/23/EEC “Low Voltage Directive” as amended
by Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen
at a level that gains proper operation in residential
areas, on business and light industrial premises and
on small-scale enterprises, inside as well as outside
of  the buildings. All places of operation are
characterised by their connection to the public low
voltage power supply system.
WARNING
Use the attached RGB cable or RS-232C cable with
this equipment so as to keep interference within the
limits of a EN55022 Class B. Use the shielded D-
SUB/5 BNC cable with this equipment so as to keep
interference within the limits of a EN55022 Class B.
Please follow WARNINGS instructions. 
						

							EN – 3
ENGLISH
Contents
Important safeguards ........................................................................... 4
Overview ............................................................................................... 6
Using the remote control ...................................................................... 8
Battery installation ......................................................................................................... 8
Installation ............................................................................................ 9
Basic connections ............................................................................... 10
Preparing the projector for operation ............................................... 12
To operate projector power ON .......................................................... 13
Menu operation .................................................................................. 15
Picture adjustment ............................................................................. 18
Advanced feature for presentation .................................................... 20
Lamp replacement ............................................................................. 22
Maintenance ....................................................................................... 23
About the terminal cover (with Anti-Theft Alarm device) ............... 24
Troubleshooting .................................................................................. 25
Indicators ............................................................................................ 26
Specifications ...................................................................................... 27
Trademark, Registered trademark
Macintosh is registered trademark of Apple Computer Inc.
Other brand or product names are trademarks or registered trademarks of their respective holders.
Note: This symbol mark is for EU countries only.
This symbol mark is according to the directive 2002/96/EC Article 10 Information for
users and Annex IV.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and compo-
nents which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately
from your household waste.
Please, dispose of this equipment at your local community waste collection/recycling centre.
In the European Union there are separate collection systems for used electrical and electronic product.
Please, help us to conserve the environment we live in! 
						

							EN – 4
Important safeguards
Please read all these instructions regarding your LCD
projector and retain them for future reference. Follow
all warnings and instructions marked on the LCD pro-
jector.
1. Read instructions
All the safety and operating instructions should
be read before the appliance is operated.
2. Retain instructions
The safety and operating instructions should be
retained for future reference.
3. Warnings
All warnings on the appliance and in the oper-
ating instructions should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug this projector from the wall outlet be-
fore cleaning it. Do not use liquid aerosol clean-
ers. Use a damp soft cloth for cleaning.
6. Attachments and equipment
Never add any attachments and/or equipment
without the approval of the manufacturer as
such additions may result in the risk of fire, elec-
tric shock or other personal injury.
7. Water and moisture
Do not use this projector near water or in con-
tact with water.
8. Accessories
Do not place this projector on an unstable cart,
stand, tripod, bracket or table. Use only with a
cart, stand, tripod bracket, or table recom-
mended by the manufacturer or sold with the
projector. Any mounting of the appliance should
follow the manufacturers instructions and
should use a mounting accessory recommended
by the manufacturer.10. Power sources
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power,
please consult your appliance dealer or local
power company.
11.Power-cord protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them. Pay particular at-
tention to cords at plugs, convenience receptacles,
and points where they exit from the appliance. Do
not put the power cord under a carpet.
12. Overloading
Do not overload wall outlets and extension cords
as this can result in a fire or electric shock.
13. Objects and liquids
Never push objects of any kind through open-
ings of this projector as they may touch danger-
ous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liq-
uid of any kind on the projector.
14. Servicing
Do not attempt to service this projector your-
self. Refer all servicing to qualified service per-
sonnel.
15. Damage requiring service
Unplug this projector from the wall outlet and
refer servicing to qualified service personnel un-
der the following conditions:
(a)If the power-supply cord or plug is dam-
aged.
(b) If liquid has been spilled, or objects have
fallen into the projector.
(c) If the projector does not operate normally
after you follow the operating instructions.
Adjust only those controls that are covered
by the operating instructions. An improper
adjustment of other controls may result
in damage and may often require exten-
sive work by a qualified technician to re-
store the projector to its normal operation.
(d)If the projector has been exposed to rain
or water.
(e)If the projector has been dropped or the
cabinet has been damaged.
(f) If the projector exhibits a distinct change
in performance - this indicates a need for
service.
16. Replacement parts
When replacement parts are required, be sure
that the service technician has used replacement
parts specified by the manufacturer or parts
having the same characteristics as the original
part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
17. Safety check
Upon completion of any service or repair to this
projector, ask the service technician to perform
safety checks determining that the projector is
in a safe operating condition.
An appliance and cart combination should be
moved with care. Quick stops, excessive force and
uneven surfaces may cause the appliance and
cart combination to overturn.
9. Ventilation
Slots and openings in the cabinet are provided
for ventilation, ensuring reliable operation of the
projector and to protect it from overheating. Do
not block these openings or allow them to be
blocked by placing the projector on a bed, sofa,
rug, or bookcase. Ensure that there is adequate
ventilation and that the manufacturers instruc-
tions have been adhered to. 
						

							EN – 5
ENGLISH
WARNING:
Unplug immediately if there is something
wrong with your projector.
Do not operate if smoke, strange noise or odor comes out
of your projector. It might cause fire or electric shock. In
this case, unplug immediately and contact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in the Owners Guide, do
not attempt to service this product yourself. Please contact
your dealer when you want to fix, adjust or inspect the
projector.
Do not modify this equipment.
It can lead to fire or electric shock.
If you break or drop the cabinet.
Do not keep using this equipment if you break or drop it.
Unplug the projector and contact your dealer for
inspection. It may lead to fire if you keep using the
equipment.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface.
Place the projection on a leveled and stable surface only.
Please do not place equipment on unstable surfaces.
Do not look into the lens when it is operating.
It may hurt your eyes.Never let children look into the lens
when it is on.
Do not turn off the main power abruptly or
unplug the projector during operation.
It can lead to lamp breakage, fire, electric shock or other
trouble. It is best to wait for the fan to turn off before
turning main power off.
Do not touch Air outlet grille and Bottom plate
which becomes hot.
Do not touch them or put other equipment in front of Air
outlet grille. The heated Air outlet grille and Bottom plate
may cause injury or damage to other equipment. Also, do
not set the projector on the desk which is easily affected by
heat.
Clean the air-filter once a month.
Clean the air-filter frequently. If the filter or ventilation slots
become clogged with dirt or dust, the temperature inside of
the projector may rise and cause some troubles, such as dam-
age of inside parts, and shortening the life of panel.
Do not look into the air outlet grille when
projector is operating.
Heat, dust etc. may blow out of it and hurt your eyes.
Do not insert your fingers in the space
between the lens and the cabinet.
The lens may shift causing injury or damage to the projector.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the
projector, causing deterioration in the projector quality
and fire.
Place of installation
For safety’s sake, refrain from setting the projector at any
place subjected to high temperature and high humidity.
Please maintain an operating temperature, humidity, and
altitude as specified below.
•Operating temperature: between +41°F (+5°C) and
+104°F (+40°C)
•Operating humidity:  between 30 and 90%
•Never put any heat-producing device under the projec-
tor so that the projector does not overheat.
•Do not attach the projector to a place that is unstable or
subject to vibration.
•Do not install the projector near any equipment that
produces a strong magnetic field. Also refrain from in-
stalling near the projector any cable carrying a large cur-
rent.
•Place the projector on a solid, vibration free surface: oth-
erwise it may fall, causing serious injury to a child or
adult, and serious damage to the product.
•Do not stand the projector: it may fall, causing serious
injury and damage to the projector.
•Slanting the projector more than ±15˚(right and left or
front and rear) may cause trouble or explosion of the
lamp.
•Do not place the projector near air-conditioning unit or
heater to avoid hot air to the exhaust and ventilation
hole of the projector.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as
set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Depart-
ment of Communications.
Changes or modifications not expressly approved by Mitsubishi could void the users authority to operate this
equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class A digital apparatus complies with Canadian ICES-003. 
						

							EN – 6
Overview
14
6 5 313 1
7 2
10 411 12
89
LAMP
VOLUME
ZOOM/
FOCUSKEYSTONE
TEMP
SOURCEMUTE AUTO  POSITION LENS SHIFT
MENUENTER
POWER
24567
8
9
10
11121317 1411815 16
3
REMOTE
INREMOTE
OUTINPUT 1
INPUT 2R/PRB/PBG/Y H/HVV
AUDIO
IN
AUDIO
OUTY
CRS-232C RS-232C/MOUSEUSB
S-VIDEO
VIDEO
2
VIDEO
1
L
AUDIO
R MAIN
AC IN
Control area
Terminal panel
1Remote control sensor (Front)
2Lens
3Control area
4Air outlet grille
5Terminal panel
6Air inlet grille
7Easy-carry handle
8Speaker
9Kensington Security Lock Standard
connector
10Remote control sensor (Rear)
1LAMP indicator
2TEMP (temperature) indicator
3AUTO POSITION button
4Direction buttons
5MENU button
6KEYSTONE button
7VOLUME (+, –) buttons
8SOURCE button
9MUTE button (Audio/Video)
10ZOOM/FOCUS button
1
 1ENTER button
12LENS SHIFT button
13POWER button
14POWER indicator
•The + and - buttons are used in the KEYSTONE and
ZOOM/FOCUS adjustment in addition to the volume
control.
1REMOTE IN jack
2Reset button
3REMOTE OUT jack
4COMPUTER / COMPONENT VIDEO INPUT 1
terminal (R/P
R, G/Y, B/PB, H/HV, V )(BNC)
5RS-232C terminal(8P)
6RS-232C/MOUSE terminal(8P)
7USB terminal
8VIDEO 2 terminal (S-Video)
9VIDEO 1 terminal (RCA)
10AUDIO terminals
1
 1VIDEO 1 terminal (BNC)
12VIDEO 2 terminals (Y,C)(BNC)
13COMPUTER AUDIO OUT jack
14COMPUTER AUDIO IN jack
15COMPUTER OUTPUT terminal (D-SUB mini
15P)
16COMPUTER / COMPONENT VIDEO INPUT 2
terminal (D-SUB mini 15P)
17Power jack
18Main power
O : OFF I : ON
213
8
9
10
5647 
						

							EN – 7
ENGLISH
Bottom side
1
2
31Adjustment foot (Left/Right)
2Air inlet grille/Filter cover
3Lamp cover
Caution:
Do not replace the lamp immediately after using the
projector because the lamp has got extremely hot.
COMPUTER
VIDEO KEYSTONE
VOLUME
LASER
EXPAND
MENU R-CLICK ENTER
P in PSTILL
MUTE
LENS SHIFT16 : 9
12
12
ZOOM/FOCUS AUTOPOSITION
1
2
4
5
6
7
8
9
10
11
12
13
3
23
22
21
24 20
19
18
17
16
15
14
Remote control1Laser aperture
2Transmission window
3Wired remote control jack
4Indicator
5POWER button
6KEYSTONE button
7ZOOM/FOCUS button
8+ , – (VOLUME) buttons
9Mouse pointer
10MENU button
1
 1STILL button
12PinP button
13LENS SHIFT button
14MUTE button (Audio/Video)
1516 : 9 button
16ENTER button
17R-CLICK button (For mouse)
18Direction buttons
19LASER button
20AUTO POSITION button
21EXPAND button
22VIDEO 1, 2 button
23COMPUTER 1, 2 button
24 Left click button (For mouse)
•The + and - buttons are used in the KEYSTONE and
ZOOM/FOCUS adjustment and the EXPAND mode in
addition to the volume control.
•Pressing the LASER button emits a laser beam. Even when
you keep holding down the LASER button, it is emitted
only one minute. To keep emitting it longer, press the
LASER button again.
•You can disable the LASER button to prevent laser
radiation due to misuse of the button.
How to disable the LASER button
While holding the LASER button down, press the }
button three times.
How to enable the LASER button
While holding the LASER button down, press the {
button three times.
About the laser beam
This remote control is a Class 2 laser product. (Max. output : 1 mW, Wavelength
: 640-660 nm)
Beam Divergence : 6m distance about 10.0mm x 10.0mm (±6.0mm)
CAUTION :
•Pressing the LASER button on the remote control emits a laser beam. Do not
look into the laser beam directly. Do not point the laser beam at anyone.
Looking at the laser beam directly may damage eyesight.
•Use of controls or adjustments or procedures other than those specified herein may
result in hazardous radiation exposure.
•This remote controller cannot be repaired.
MADE  IN  CHINA
MANUFACTURER :   B 
MANUFACTURED RAYONNEMENT LASER
NE PAS REGARDER DANS LE FAISCEAU
APPAREIL A LASER DE CLASSE2
LASER-STRAHLUNG 
NICHT IN DEN STRAHL BLICKEN
LASER KLASSE 2
RADIAZIONl LASER
NON GUARDARE NEL RAGGIO LUCE
APPARECCHIO LASER DI CLASSE 2
WAVE LENGTH :640-660nm MAX OUTPUT:1mW
IEC60825-1:1993+A1:1997+A2:2001
INTERLINK K.K.
SHINODA BLDG 1-10-7 HIGASHIKANDA CHIYODA-KU,TOKYO 101-0031,JAPANLASER RADIATION
DO NOT STARE INTO BEAM
WAVE  LENGTH:640-660nmMAX  OUTPUT:1mWCLASS  2  LASER  PRODUCT
AVOID  EXPOSURE-LASER
RADIATION  IS  EMITTED
  FROM  
THIS  
APERTURE
CAUTION
Comp l ies  w i t h   2 1   CFR, 1040. 10  and  1040. 11
JANUARY  2003
RADIAÇÃO LASER
EVITAR A EXPOSIÇÃO AO FEIXE
APARELHO LASER DA CLASSE 2
POTÊNCIA MÁXIMA: 1mW
COMPRIMENTO DE ONDA: 640 - 660 nm 
						

							EN – 8
Battery installation
Use two AA size batteries.
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the
arrow.
2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
•Load the batteries from - spring side, and make sure to set them tightly.
3. Replace the back cover.
Important:
•Use of a battery of wrong type may cause explosion.
•Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
•Dispose of used batteries according to your local regulations.
•Batteries may explode if misused.
•Do not recharge, disassemble, or dispose of in fire.
•Be sure to handle batteries according to the instructions.
•Load batteries with the positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
•Keep batteries out of reach of children and pets.
•Remove the batteries, if the remote control is not used for a long time.
•Do not combine a new battery with an old one.
•If the solution of batteries comes in contact with your skin or clothes, rinse with water. If  the solution comes
in contact with your eyes, rinse them with water and then consult your doctor.
Operation area (for wireless control system)
The range for operation is about 10 m (about 32 feet) when the remote control points to the projector. The dis-
tance to the screen back to the projector must be less than 7 m (about 23 feet). Depending on the type of the
screen, the distance will be different.
Important:
Avoid the direct sunlight or fluorescent light to the remote control sensor. Also keep the distance of more than 2 m
(6.5 feet) between the remote control sensor and fluorescent lamp on the remote control may not work correctly.
Using the wired remote control
Attached remote control for this projector can be used as a wired remote control with remote control cable. Wired
remote control is useful for operating in a distance or outside of the operating area.
20˚
15˚20˚
15˚
30˚ 30˚
12 3
•When REMOTE OUT terminal on this projector is connected to 
the REMOTE OUT terminal on the other projector, the two 
projectors can be controlled together by using the remote 
control. (Up to two projectors can be controlled.)
REMOTE IN
REMOTE OUT
REMOTE IN
REMOTE
INREMOTE
OUTINPUT 1
INPUT 2R/PRB/PBG/Y H/HVV
AUDIO
IN
AUDIO
OUTY
CRS-232C RS-232C/MOUSEUSB
S-VIDEO
VIDEO
2
VIDEO
1
L
AUDIO
R MAIN
AC IN
•When the remote control is connected
with remote control cable, it does not
work as a wireless remote control.
•For connection, use the pin-pin cable of
ø3.5 stereo type, which is commercially
available. However, some cable may not
work correctly.
•When using the wired remote control, the
laser beam may be darker. It is normal.
Using the remote control
20˚
20˚ 
						

							EN – 9
ENGLISH
Installation
Orientation of the projector
Picture size can be set by changing the distance between the screen and the projector.
Front projection
Front projection, ceiling mount
For ceiling mount, you need the ceiling mount kit.
Ask a specialist for installation. For more details,
consult your dealer.
•This warranty does not cover damage caused by
the use of any unrecommended ceiling mount kit
and the installation of the ceiling mount kit at an
improper location.
•When using the ceiling mount, set IMAGE RE-
VERSE in the INSTALLATION menu to MIR-
ROR INVERT. See Page 16.
•Projected images may appear darker when the
unit is used as a ceiling installation than when it
is used in the tabletop position. This does not
signify a product malfunction.
Rear projection
Ask a specialist for installation.  For more details,
consult your dealer.
•For rear projection, set IMAGE REVERSE in the
INSTALLATION menu to MIRROR.  See Page 16.
Screen
Caution:
•Placing the projector on a carpet reduces ventila-
tion from the fan at the bottom and might cause
problems. Place a hard board or similar item
under the projector to facilitate ventilation of the
unit.
•Place the projector more than 50 cm (20 inch)
from the wall to prevent blocking the intake,
exhaust slots and ventilation of this projector
because hot air comes out of it.
•Do not use the projector under the following
circumstances, which may cause fire or electric
shock.
•in a dusty or humid place
•while the projector is lying sideways or upside
down
•near a heater
•in a kitchen or oily, smoky or damp place
•in direct sunlight
•with high temperature, such as a closed car
•where the temperature is lower than 41°F
(+5˚C) or higher than 104°F (40˚C).
Important:
•Do not put stress on the lens, as this may cause
damage.
L
 L
I
WW
H
Height
Width
Center of 
the lens*
* Center of the lens when the image is projected 
   along the top of the maximum projection area.The maximum projection area
For XL5980U only. For XL5980LU, please refer to page 30.
•The above numbers are approximate, and may be slightly different from the actual measurements.inch
36
48
60
90
120
150
180 cm
122
163
203
305
406
508
610 inch
60
80
100
150
200
250
300inch
48
64
80
120
160
200
240m
2.3
3.0
3.8
5.8
7.7
9.7
11.6m
2.9
3.9
4.9
7.3
9.8
12.3
- inch
89
120
150
227
304
381
458inch
114
153
191
289
386
483
- cm
91
122
152
229
305
381
457 cm
152
203
254
381
508
635
762
ScreenDistance from the screen : L
Maximum
zoom (WIDE)Minimum
zoom (TELE)Diagonal sizeWidthHeight
cm
5
6
8
11
15
19
23cm
42
56
69
104
138
172
207 inch
1.8
2.4
3.0
4.5
6.0
7.5
9.0inch
16.6
22.0
27.4
40.9
54.4
67.9
81.4
Lens shift height
Standard : I
Movement
Distance : H
cm
6
8
10
15
20
26
31 inch
2.5
3.3
4.1
6.1
8.1
10.1
12.1
Lens shift
width : W
Front projection, ceiling mount
WWWidth
Height
H
I
L
 L
Center of 
the lens*
* Center of the lens when the image is projected 
   along the bottom of the maximum projection area.The maximum projection area 
						

							EN – 10
Basic connections
This projector can be connected with various devices such as a VCR, video camera, videodisc player, and personal
computer that have analog RGB output connectors.
Important:
•Make sure that the connected device is turned off before starting connection.
•Plug in the projector and the connected devices firmly, and unplug them by holding and pulling out their
power plugs, not by pulling the power cords.
•When the projector and the connected devices are located too close to each other, the projected image may be
affected by their interference.
•See the owner’s guide of each device for details about their connections.
Projector + AV device
Important:
•Connect the video and audio plugs of the AV cable to the proper terminals matching their colors respectively.
•When the connected AV device uses a BNC connector for its video output, connect it to the VIDEO 1 (BNC)
terminal. When both the VIDEO 1 (BNC) terminal and the VIDEO 2 (RCA) terminal are engaged at the same
time, the image supplied to the VIDEO 2 (RCA) terminal takes priority.
•When the connected AV device uses a BNC connector for its S-video output, connect it to the VIDEO 2
(Y,C)(BNC) terminal. When both the VIDEO 2 (Y,C) (BNC) terminal and the S-VIDEO 2 terminal are engaged
at the same time, the image supplied to the S-VIDEO 2 terminal takes priority.
B 
G 
R/PR  G/Y  B/P
B 
R 
CB(PB)
Y
C
R(PR) 
DVD player or HDTV decoder
BNC-RCAconnector
(option)
BNC-BNC cable (option)
AUDIO cable (option)COMPUTER AUDIO IN
to AUDIO OUT
Projector + DVD player or HDTV decoder
Some DVD players have an output connector for 3-line fitting (Y, CB, CR). When connecting such a DVD player
with this projector, use the COMPUTER/COMPONENT VIDEO INPUT 1  terminal.
•The terminals’ names Y, P
B, and PR are examples of a case where a HDTV decoder is connected.
•The terminals’ names are different depending on the connected devices.
•Use BNC-BNC cables for connection.
•The image may not be projected correctly with some DVD players.
•When connecting a HDTV decoder having RGB output terminals, set the COMPUTER INPUT to RGB in the
SIGNAL menu.
To S-video input To S-video output
To video input
To audio inputTo video output To audio output
VCR, etc. S-VCR, etc.
To Y input
To S input To Y output
To S output
To audio inputTo video output To audio output
VCR, etc. S-VCR, etc.
To video input
When using the video (RCA) or S-video connectorWhen using the BNC connector