Mitsubishi Xd8100u Dlp Projector User Manual

							EN-71
Indicators
This projector has 5 indicators, each of which shows the operation condition of the projector. 
The following offer solutions to possible problems. If these problems persist, turn the projector off and consult your 
dealer. 
POWER indicator
FILTER indicator
LAMP 1 indicator
STATUS indicator
LAMP 2 indicator
 POWER, STATUS, and FILTER: The current condition is indicated. 
POWER STATUS FILTER CONDITION POSSIBLE SOLUTION
Normal 
condition
Steady redOffOffPower standby or cooling
Steady green
OffOffThe power is on (Normal condition) The lamp condition is indicated by 
the LAMP indicators. 
OffBlinking greenAutomatic cleaning fi lter is working. Don’t turn off the power before the 
indicators go out. 
Abnormal 
condition
Blinking green/
red
OffOff
•  Any of the lamp cover, fi lter cover, and 
color wheel replacement cover*2 is 
open. 
•  The automatic cleaning fi lter unit isn’t 
mounted. •  Close all the covers. 
•  Mount the automatic cleaning 
fi lter unit. (See page 66.)
Steady*1or
Blinking*1
Abnormal Contact your dealer.
Steady greenOffBlinking orangeThe automatic cleaning fi lter isn’t working 
correctly. 
Steady red
or
Steady green
Blinking orangeOff
Abnormal temperature
•  The ventilation grilles are clogged with 
dust or dirt.
•  The room temperature is high.
• The fi lter is dirty. •  Clean the ventilation grilles.
•  Relocate the projector to a cooler 
place.
•  Clean the fi lter. (See page 66.) 
*1:  Status of either or both of the indicators.
*2:  You can replace it with a separately sold color wheel. (See page 72.)
LAMP 1, LAMP 2: The condition of each lamp is indicated. 
LAMP 1 / LAMP 2CONDITION POSSIBLE SOLUTION
Normal 
condition
Blinking green
• When the lamp is illuminating, it is in the 
warmup mode. (You cannot turn off the 
power.) 
• When the lamp is off, it is in the cooling 
mode. (You cannot turn on the power.) 
Steady greenThe lamp is illuminating.
Replacement
Blinking red
or
Blinking green/red
Lamp operation time warning. (Total lamp 
operation time reached 3000 hours*3.)Replace the light source lamp indicated by the 
illuminating or blinking indicator.
Change with a new lamp if this problem 
recurs.
Steady redLamp operation time warning. (Total lamp 
operation time reached 4000 hours*3*4.)
Abnormal 
conditionBlinking orange
The protection circuit is working or the lamp 
is in an abnormal condition.
When only one lamp fails:
• 
In the case that LAMP SELECT is set to 
DUAL, only the normal lamp illuminates 
(the intensity of one lamp is obtained).
• In the case that LAMP SELECT is set to 
SINGLE, LAMP 1, or LAMP 2, only the 
normal lamp illuminates (the lamp isn’t 
switched).When both indicators blink, wait until the 
indicators stop blinking and then press the 
POWER button. If the light source lamps don’t 
illuminate even after you perform the above 
operation several times, unplug the power cord 
from the wall outlet and contact your dealer.
To illuminate the failed lamp again when either 
indicator blinks, turn off the power and wait until 
the indicator stops blinking and then press the 
POWER button. If the light source lamp doesn’t 
illuminate even after you perform the above 
operation several times, unplug the power cord 
from the wall outlet and contact your dealer.
*3: Duration when LAMP MODE of the INSTALLATION 1 menu is set to LOW. When it is set to STANDARD, this duration will be shorted.*4:  When LAMP MODE is set to STANDARD, this duration will be shorted up to 2000 hours.  
						

							EN-72
Specifi cations
The specifi cations and outside appearance of the projector are subject to change without prior notice.
Type DLP™ projector
Model XD8100U
Display technology 0.7-inch Single chip DMD
Pixel 1024 x 768 = 786432 pixels
Projection lens F 2.0 - 2.4  f= 24.5 - 33.1 mm
Light-source lamp 330 W x 2
Image size (projection distance)40” min. to 300” max. (projection distance 1.4 to 10.6 m)
Maximum resolution Computer signalMaximum resolution:  1920 x 1200 dots (compressed)
Panel resolution: 1024 x 768 dots
Video signal NTSC/PAL/SECAM/4.43NTSC/PAL-M/PAL-N/PAL-60 
Component signal 480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Panel resolution: 1024 x 768 dots
Computer/component video input [Signal type]  [Terminal type]  [Line]
Analog RGB  Mini D-SUB 15-pin  1
Analog RGB  5 BNC  1
Digital RGB  DVI-D 24-pin  1
Video input [Signal type]  [Terminal type]  [Line]
Video input  BNC  1 
S-video input  S   1
HDMI input [Signal type]  [Terminal type]  [Line]
HDMI HDMI 19-pin 1
Control terminal/others SERIAL IN/OUT (D-SUB 9-pin male) RS-232C standards, 
LAN (RJ-45), REMOTE 1 IN (D-SUB 9-pin female), REMOTE2 IN/OUT 
(Stereo mini jack (ø3.5))
Operating temperatures +41°F (+5°C) to +104°F (+40°C): ( Standard altitude mode: Floor 
installation/ceiling installation)
+41°F (+5°C) to +95°F (+35°C): (Other than above.)
Rated voltage AC 100 - 240 V, 50/60 Hz
Power consumption 8.7 A, 860 W
During standby: 
AC 100 - 120 V:  2 W (when STANDBY MODE is STANDARD)
0.2 W (when STANDBY MODE is LOW)
AC 220 - 240 V:  2 W (when STANDBY MODE is STANDARD)
0.3 W (when STANDBY MODE is LOW)
Dimensions (not including protrusion) 490 mm (W) x 201 mm (H) x 421 mm (D) (projector only)
490 mm (W) x 201 mm (H) x 506 mm (D) (including the terminal cover)
Weight 16 kg (projector only), 16.5 kg (including the terminal cover)
Others S-video input Luminance signal: Vp-p=1.0 V 75 Ω (negative sync)
Chrominance signals: Vp-p=0.286 V 75 Ω (burst signal)
Video input Vp-p=1.0 V 75 Ω (negative sync)
Component video 
inputYC
BCR: Vp-p=1.0 V 75 Ω (Y) (negative sync)
  Vp-p=0.7 V 75 Ω (C
B, CR)
Analog input RGB: Vp-p=0.7 V 75 Ω (negative sync)
YC
BCR: Vp-p=1.0 V (Y) (negative sync)  Vp-p=0.7 V (CB, CR)
HD/CS: TTL-level (negative or positive polarity)
VD: TTL-level (negative or positive polarity)
Digital input (DVI) DVI-D interface (TMDS single link) with HDCP
Digital input (HDMI)HDMI interface (TMDS single link)
Replacement part (option/not included in the box)
Spare lamp: VLT-XD8000LP
Option lenses: OL-XD2000SZ, OL-XD2000LZ, OL-XD2000TZ, OL-XD8000UZ, OL-XD2000FR
Option color-wheel: CW-FC2 
						

							EN-73
Specifi cations (continued)
Specifi cation of RGB signals in each computer mode of the projector
Signal mode Resolution
(H x V)Horizontal frequency 
(kHz)Vertical frequency (Hz) Normal mode
(H x V)
TV60, 480i (525i) 720 x 480 15.73 59.94 1024 x 768 *1
TV50, 576i (625i) 720 x 576 15.63 50.00 1024 x 768 *1
1080i60 (1125i60) 1920 x 1080 33.75 60.00 1024 x 576 *1, *2, *3
1080i50 (1125i50) 1920 x 1080 28.13 50.00 1024 x 576 *1, *2, *3
480p (525p) 720 x 480 31.47 59.94 1024 x 768 *1, *2, *3
576p (625p) 720 x 576 31.25 50.00 1024 x 768 *1, *2, *3
720p60 (750p60) 1280 x 720 45.00 60.00 1024 x 576 *1, *2, *3
720p50 (750p50) 1280 x 720 37.50 50.00 1024 x 576 *1, *2, *3
1080p60 (1125p60) 1920 x 1080 67.50 60.00 1024 x 576 *1, *2, *3
1080p50 (1125p50) 1920 x 1080 56.25 50.00 1024 x 576 *1, *2, *3
CGA70 640 x 400 31.47 70.09 1024 x 640
CGA84 640 x 400 37.86 84.13 1024 x 640
CGA85 640 x 400 37.86 85.08 1024 x 640
VGA60 640 x 480 31.47 59.94 1024 x 768 *2, *3
VGA72 640 x 480 37.86 72.81 1024 x 768
VGA75 640 x 480 37.50 75.00 1024 x 768
VGA85 640 x 480 43.27 85.01 1024 x 768
SVGA56 800 x 600 35.16 56.25 1024 x 768
SVGA60 800 x 600 37.88 60.32 1024 x 768 *2, *3
SVGA72 800 x 600 48.08 72.19 1024 x 768
SVGA75 800 x 600 46.88 75.00 1024 x 768
SVGA85 800 x 600 53.67 85.06 1024 x 768
SVGA95 800 x 600 59.97 94.89 1024 x 768
XGA60 1024 x 768 48.36 60.00 1024 x 768 *2, *3
XGA70 1024 x 768 56.48 70.07 1024 x 768
XGA75 1024 x 768 60.02 75.03 1024 x 768
XGA85 1024 x 768 68.68 85.00 1024 x 768
SXGA70a 1152 x 864 63.85 70.01 1024 x 768
SXGA75a 1152 x 864 67.50 75.00 1024 x 768
SXGA85a 1152 x 864 77.49 85.06 1024 x 768
WXGA60 1280 x 768 47.78 59.87 1024 x 614
WXGA60a 1280 x 800 49.70 59.81 1024 x 640 *2
WXGA60b 1360 x 768 47.71 60.02 1024 x 578
WXGA60c 1366 x 768 47.50 59.75 1024 x 576
WXGA+60 1440 x 900 55.94 59.89 1024 x 640 *2, *3
SXGA60b 1280 x 960 60.00 60.00 1024 x 768
SXGA75b 1280 x 960 75.00 75.00 1024 x 768
SXGA85b 1280 x 960 85.94 85.00 1024 x 768
SXGA60 1280 x 1024 63.98 60.02 960 x 768 *2, *3
SXGA75 1280 x 1024 79.98 75.02 960 x 768
SXGA85 1280 x 1024 91.15 85.02 960 x 768
SXGA+601400 x 1050 63.98 60.02 1024 x 768
1400 x 1050 65.32 59.98 1024 x 768 *2, *3
SXGA+75 1400 x 1050 82.28 74.87 1024 x 768
WSXGA+60 1680 x 1050 65.29 59.95 1024 x 640
MAC13 640 x 480 35.00 66.67 1024 x 768
MAC16 832 x 624 49.72 74.55 1024 x 768
MAC19 1024 x 768 60.24 75.02 1024 x 768
HP75 1024 x 768 62.94 74.92 1024 x 768
HP72 1280 x 1024 78.13 72.00 960 x 768
SUN66a 1152 x 900 61.85 66.00 984 x 768
SUN76a 1152 x 900 71.81 76.64 984 x 768
SUN66 1280 x 1024 71.68 66.68 960 x 768
SUN76 1280 x 1024 81.13 76.11 960 x 768
SGI72 1280 x 1024 76.92 72.30 960 x 768
SGI76 1280 x 1024 82.01 76.00 960 x 768
UXGA60 1600 x 1200 75.00 60.00 1024 x 768 *2, *3
WUXGA60 1920 x 1200 74.04 59.95 1024 x 640
*1:  The PinP mode, the MAGNIFY mode and IMAGE CAPTURE in the INSTALLATION 2 menu don’t function with these signals.
*2:  The COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP) terminal is available for these signals.
*3:  The HDMI IN terminal is available for these signals.  
						

							EN-74
490
201120*
421
Dimension drawings (unit: mm)
Specifi cations (continued)
Specifi cation of RGB signals in each computer 
mode of the projector (continued)
Important:
•  Some computers aren’t compatible with the 
projector.
•  The projector’s maximum resolution is 1024 x 
768 pixels. It may not display images of higher 
resolutions than 1024 x 768 correctly.
•  Images with SYNC on G (Green) signal may jitter.
•  Images with SYNC on G (Green) signal may be 
tinged with green.
•  If the resolution and frequency of your computer 
aren’t shown on the table, fi nd the compatible 
resolution and frequency by changing the resolution 
of your computer.•  TV60 and TV50 are equivalent to 480i and 576i 
respectively. When these signals are supplied to 
the VIDEO IN or S-VIDEO IN terminal, the signal 
mode is indicated as TV60 or TV50. When they are 
supplied to the COMPUTER/COMPONENT VIDEO 
IN terminals, the signal mode is indicated as 480i or 
576i. 
•  This projector doesn’t support 480p signals from 
video devices having 4 lines (R, G, B, CS*) or having 5 
lines (R, G, B, H, V). 
  * : Composite Sync
490506
201120*
Without terminal cover
With terminal cover
Connectors
SERIAL IN/OUT 
(D-SUB 9-pin)
1 5
6 9
Pin No.Name I/O
1– –
2 TXD IN
3 RXD OUT
4– –
5 GND –
6– –
7– –
8– –
9– –
COMPUTER/COMPONENT VIDEO 
IN-1 (Mini D-SUB 15-pin)
1 5
116 10
15
Pin No.Spec.Pin No.Spec.
1 R(RED)/PR/CR9 DDC 5V
2 G(GREEN)/Y 10 GND
3 B(BLUE)/P
B/CB11 GND
4 GND 12 DDC Data
5 GND 13 HD/CS
6 GND 14 VD
7 GND 15 DDC Clock
8 GND
COMPUTER/COMPONENT VIDEO 
DVI-D IN (HDCP) 
(DVI-D 24-pin)
1724
169
8
1
Pin No.Spec.Pin No.Spec.1 TMDS DATA 2- 13-2 TMDS DATA 2+ 14+5V Power3TMDS DATA 2 Shield15Ground (for +5V)4-16 Hot Plug Detect
5-17 TMDS DATA 0-
6 DDC Clock    18 TMDS DATA 0+
7 DDC Data 19
TMDS DATA 0 Shield8-20-9 TMDS DATA 1- 21-10 TMDS DATA 1+ 22TMDS Clock Shield11TMDS DATA 1 Shield 23 TMDS Clock+
12-24 TMDS Clock-
HDMI IN
(HDMI 19-pin)
191
2
18
Pin No.Spec.Pin No.Spec.1TMDS Data2+11TMDS Clock Shield2TMDS Data2 Shield12TMDS Clock-3TMDS Data2-13CEC4TMDS Data1+14–5TMDS Data1 Shield15SCL6TMDS Data1-16SDA7TMDS Data0+17DDC Ground8TMDS Data0 Shield18+5 V Power9TMDS Data0-19Hot Plug Detect10TMDS Clock+
*: Factory-defaults 
						

							1 Zusho Baba, Nagaokakyo-City, Kyoto Japan
MITSUBISHI ELECTRIC CORPORATION
U-B