Mitsubishi Xd8100u Dlp Projector User Manual

U
XD8100
This User Manual is important to you.
Please read it before using your projector.
DLP™ PROJECTOR
MODEL
XD8100U
User Manual 

EN-2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC 
SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE 
PERSONNEL.
The lightning fl ash with arrowhead symbol within an equilateral triangle is intended to alert 
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure 
that may be of suffi cient magnitude to constitute a risk of electric shock.
The exclamation point within an...

EN-3
Contents
Important safeguards ........................................................................................................................ 4
Preparing your projector .................................................................................................................... 6
Using the remote control ................................................................................................................... 9
Setting up your projector...

EN-4
Important safeguards
Please read all these instructions regarding your 
projector and retain them for future reference. Follow 
all warnings and instructions marked on the projector.
1. Read instructions
  All the safety and operating instructions should be 
read before the appliance is operated.
2. Retain instructions
  The safety and operating instructions should be 
retained for future reference.
3. Warnings
  All warnings on the appliance and in the operating 
instructions should be adhered to....

EN-5
Important safeguards (continued)
WARNING:
Unplug immediately if there is something 
wrong with your projector.
Do not operate if smoke, strange noise or odor comes 
out of your projector. It might cause fi re or electric 
shock. In this case, unplug immediately and contact 
your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An 
inadvertent contact may result in an electric shock. 
Except as specifi cally explained in the User Manual do 
not attempt to service this...

EN-6
Preparing your projector
1Checking accessories
The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in 
the package. 
Cables
Remote control parts
Remote control
(290P188-10)RS-232C cable
(246C598-20)R6 (size-AA) 
battery (two) 
RGB cable for PC 
(246C597-20)
Others
•  Lens cap (attached to the projector)
• Terminal cover
•  Lamp replacement tray
• CD-ROM
•  Safety Manual/Quick Start up 
•  Mitsubishi logo plate
•  Control panel label for...

EN-7
Overview
34756108
1
911
212
6
7
8
9
10 1
3
4
52
1 Indicators
2  Air inlet grille/Filter cover
3  Air outlet grille
4 Lens
5  Remote control sensor (front)
6  Mitsubishi logo plate position
  (Put the plate according to the 
installation orientation.)
7  Air inlet grille
8 Control area
9 Terminal panel
10 Remote control sensor (rear)
11 Air outlet grille
12 Lamp cover
Control area
When installing the projector on the ceiling, put the control panel label for ceiling installation that is supplied with...

EN-8
2
112 34 5
Preparing your projector (continued)
Bottom side
Indicators
1  Lock bar (SECURITY ANCHOR)
•  Attach a chain, etc. to this lock bar to anchor 
the projector.
2 Adjustment feet
1 FILTER indicator
2 STATUS indicator
3  LAMP 2 indicator
4  LAMP 1 indicator
5 POWER indicator
2
2922
23
25 15 13
16
17
18
19 12
21 20
314
27
28
26
4
5
1
6
7
8
24
9
10
11
Remote control
1 Indicator
2 POWER button
3  COMPUTER 1, 2 buttons
4 MENU button
5 BLANK button
6 ZOOM/FOCUS button
7 ID button
8 MAGNIFY button
9...

EN-9
Using the remote control
Using the wired remote control
Attached remote control for this projector can be used as a wired remote control with remote control cable. Wired 
remote control is useful for operating in a distance or outside of the operating area.
REMOTE 2 IN
REMOTE 2 OUT
REMOTE 2 IN•  For connection, use the pin-pin cable of ø3.5 stereo type, 
which is commercially available. However, some cable may 
not work correctly.
•  When REMOTE 2 OUT terminal on this projector is 
connected to the...

EN-10
Using the remote control (continued)
Setting the ID number of the remote 
control
You can control multiple projectors collectively or 
individually using one remote control by setting the ID 
number (CONTROLLER ID) of the remote control. 
To control multiple projectors using the remote 
control, you need to select the projector’s ID number 
(PROJECTOR ID) with the remote control in advance. 
ID numbers should be two-digit numbers “01” to “63” 
or “ALL.” Other numbers cannot be used.
•  For setting...