Mitsubishi Xd8100u Dlp Projector User Manual

							EN-51
6.  When selecting OK, the setting is completed as 
the IP ADDRESS stored. However, when selecting 
CANCEL, the setting is completed without storing.
•  When the setting you entered is correct, the 
setting change dialog is displayed. After the 
dialog disappears, the NETWORK menu is 
displayed. If the entered content is not correct, 
IP ADDRESS screen appears again after an 
error dialog is displayed.
•  It may take some time to refl ect the settings.
Subnet Mask Settings
1.  Display the IP CONFIG menu.
2. Press the  or  button to select SUBNET MASK.
SUBNET MASK
0. 0. 0. 0
3. Press the  or  button to select SET .
4.  Press the ENTER button.
•  SUBNET MASK screen appears.
SUBNET MASK
255 . 255 .  255 .    0
0
OKCLEARDEL
CANCEL
123456789
←→
5.  Enter the Subnet Mask.
•  Refer to IP Address Settings for the detail of 
entering.
6.  When selecting OK, the setting is completed as 
the Subnet Mask stored. However, when selecting 
CANCEL, the setting is completed without storing.
•  When the setting you entered is correct, the 
setting change dialog is displayed. After the 
dialog disappears, the NETWORK menu is 
displayed. If the entered content is not correct, 
SUBNET MASK screen appears again after an 
error dialog is displayed.
•  It may take some time to refl ect the settings.
Default Gateway Settings
1.  Display the IP CONFIG menu.
2. Press the  or  button to select DEFAULT 
GATEWAY.
DEFAULT GATEWAY
0. 0. 0. 0
3. Press the  or  button to select SET .
4.  Press the ENTER button.
•  DEFAULT GATEWAY screen appears.
DEFAULT GATEWAY
10 . 132 .    1 .    1
0
OKCLEARDEL
CANCEL
123456789
←→
5.  Enter the Default Gateway.
•  Refer to IP Address Settings for the detail of 
entering.6.  When selecting OK, the setting is completed as the 
Default Gateway stored. However, when selecting 
CANCEL, the setting is completed without storing.
•  When the setting you entered is correct, the 
setting change dialog is displayed. After the 
dialog disappears, the NETWORK menu is 
displayed. If the entered content is not correct, 
DEFAULT GATEWAY screen appears again after 
an error dialog is displayed.
•  It may take some time to refl ect the settings.
Enabling or disabling the network 
certifi cation
You can select whether or not to certify the network 
communication using the network password.
•  For details, contact your dealer. 
(See page 32 for menu setting.)
1.  Display the NETWORK menu. 
2. Press the  or  button to select NET WORK 
CERTIFICATION.
NETWORK CERTIFICATION
ON
3.  Press the ENTER button.
• Confi rmation dialog appears.
NETWORK CERTIFICATION :
OK : ENTER   CANCEL : MENUON
4. Press the or  button to select ON  or OFF .
5.  Press the ENTER button.
•  To cancel the setting, press the MENU button.
•  It may take some time to refl ect the settings.
Setting the control system
Set the control system.
(See page 32 for menu setting.)
1.  Display the NETWORK menu. 
2. Press the  or  button to select CONTROL 
SYSTEM.
CONTROL SYSTEM
STANDARD
3.  Press the ENTER button.
CONTROL SYSTEM :
OK : ENTER   CANCEL : MENUSTANDARD
4. Press the or  button to select STANDARD , 
AMX 
, or CRESTRON .
 STANDARD
Select this setting when using ProjectorView.
 AMX
  Select this setting when using the controller of 
AMX. (See page 58.)
 CRESTRON
 
Select this setting when using the controller or 
software of Crestron Electronics, Inc. (See page 58.)
5.  Press the ENTER button.
Initial network settings (continued) 
						

							EN-52
Initialization of Network Settings
(See page 32 for menu setting.)
1.  Display the NETWORK menu. 
2. Press the  or  button to select NETWORK 
RESET.
NETWORK RESET
OK
3.  Press the ENTER button.
• Confi rmation dialog appears.
4.  If pressing the ENTER button again, the Network 
Settings can be initialized.
•  It may take some time to refl ect the settings.
How to Use Network Function 
•  When connecting a computer and projector with 
LAN, confi gure the both IP Addresses in the 
same network group.
  If connecting in different network group, be sure 
to use a router. As for the settings of a router, ask 
the network administrator.
• Confi gure the IP CONFIG correctly. If the settings 
are not correct, the communication may be 
unavailable. For the detail, consult the network 
administrator.
•  Depending on the settings of standby mode of 
the projector, LAN function may be unavailable. 
See page 34 for the detail of standby mode.
Initial network settings  (continued)
Glossary
For more detail of the glossary below, refer to the 
technical book that is commercially available.
Term Description
DHCPAbbreviation for Dynamic Host 
Confi guration Protocol. This 
protocol automatically assigns IP 
Address to networked devices.
IP AddressNumerical address to identify 
networked computers.
Subnet MaskA numeric value to defi ne the 
number of bits used for a network 
address of a divided network (or 
subnet) in an IP Address.
Default GatewayA server (or router) to communicate 
across networks (subnets) that are 
divided by Subnet Mask.
MAC Address
Abbreviation for Media Access 
Control Address. MAC Address is a 
unique ID number assigned to each 
network adapter. And this is based 
on which data are sent and received 
between network adapters. 
						

							EN-53
Lamp relay
Using the lamp relay function, you can project images 
continuously. The lamp relay function automatically 
rests or switches the lamps. The lamp relay is 
performed when LAMP SELECT in the INSTALLATION 
1 menu is set to DUAL or SINGLE. 
Setting the lamp relay interval
When LAMP SELECT is set to DUAL:
Either of the lamps is automatically put to rest.
(See page 32 for menu setting.)  
1.  Display the INSTALLATION 1 menu.
2. 
Select LAMP SELECT by pressing the  or  button.
12LAMP SELECT
DUAL
3.  Press the ENTER button.
4. Select DUAL 
 by pressing the  or  button.
LAMP SELECT
12LAMP SELECTDUAL
5.  Press the ENTER button.
6. 
Select LAMP RELAY by pressing the  or  button.
LAMP RELAY
1H/24H
7. Select 1H/24H  or 2H/1W  by pressing the  or 
 button.
1H/24H   .....Select this setting when the lamp 
is operated at a specifi ed time of 
the day. During the continuous 
projection, LAMP 1 or LAMP 2 is 
automatically turned off for 1 hour 
in 24 hours.  After the interval is set, 
the lamps are turned off for 1 hour 
alternately at the specifi ed interval. 
IlluminatingOff
LAMP 1
LAMP 2
12 3 4 5 6 7 8 (days) At the time of power-on or menu setting
2H/1W   ......During the continuous projection, 
LAMP 1 or LAMP 2 is automatically 
turned off for 2 hours in a week. 
After the interval is set, the lamps are 
turned off for 2 hours alternately at 
the specified interval.
IlluminatingOff
LAMP 1
LAMP 2
12 3 4 5 6 7 8 (days) At the time of power-on or menu setting
8.  Press the ENTER button.
•  When you select 1H/24H 
 or 2H/1W , the 
box to set the lamp relay interval is displayed. 
•  When the projector is turned off, the setting is 
cleared and the projector resumes operation 
from the time of the power-on or menu setting 
shown in the preceding step.1H/24H 
NEXT LAMP RELAY
23H
0
OKCLEARDEL
CANCEL
123456789
←→
2H/1W 
NEXT LAMP RELAY
6D 22H
0
OKCLEARDEL
CANCEL
123456789
←→
9.  Move the key cursor using the direction buttons to 
select the number you want to enter and then press 
the ENTER button.
• Maximum interval
 1H/24H  ..... 23H (23 hours)
 2H/1W 
 ...... 6D 22H (6 days and 22 hours)
 key:   Shifting the position of enter cursor 
to the left for each character.
 key:   Shifting the position of enter cursor 
to the right for each character.
 DEL key:   Deleting the character in the 
position of enter cursor for each 
character.
 CLEAR 
key:  Deleting all the entered characters.
•  You can enter the value by pressing the number 
buttons (0 to 9) while holding down the NUM 
button on the remote control. 
•  When the value you entered meets the following 
conditions, an error dialog box is displayed at 
the screen center. 
 ∙  The value has been cleared by DEL or CLEAR 
and left blank. 
 ∙  The value you entered is out of the setting 
range.
   1H/24H
  ....  24H or over
   2H/1W
   .....  6D 23H or over
 ∙  The value of each item is out of the setting 
range.
    D ..................  7 or over (2H/1W
  only)
    H ..................  24 or over
10. When selecting OK, the setting is completed as 
the lamp-switching interval stored. However, when 
selecting CANCEL, the setting is completed without 
storing.
•  The display returns the LAMP RELAY menu after 
selecting OK or CANCEL.
•  The setting you made is applied to NEXT LAMP 
RELAY in the INFORMATION menu.
Important:
•  When you use the projector continuously, the lamp 
relay may not be performed on time due to errors of 
the clock function.  
						

							EN-54
•  Immediately after the power-on, during the lamp 
selection, or during the lamp relay operation, you 
cannot change the setting of LAMP SELECT and 
LAMP RELAY. 
•  In the case of continuous projection, the lamps may 
deteriorate earlier unless they are turned off for 1 
hour per week. 
•  When using this projector continuously for a long 
time of period, enable LAMP RELAY.
•  The brightness and color tint vary at the time of 
lamp switching.
When LAMP SELECT is set to SINGLE:
The lamps are automatically switched and used alternately.
(See page 32 for menu setting.)  
1.  Display the INSTALLATION 1 menu.
2. 
Select LAMP SELECT by pressing the  or  button.
12LAMP SELECT
DUAL
3.  Press the ENTER button.
4. Select SINGLE 
 by pressing the  or  button.
LAMP SELECT
12LAMP SELECT
SINGLE
5.  Press the ENTER button.
6. 
Select LAMP RELAY by pressing the  or  button.
LAMP RELAY
24H
7. Select 24H  or 1 WEEK  by pressing the  or  
button.
24H  .........  The lamps are switched to each other 
every day. 
OffIlluminatingLAMP 1
LAMP 2
12 3 4 5 6 7 8 (days) At the time of power-on or menu setting
1 WEEK  ..  The lamps are switched to each other 
every week.
LAMP 1
IlluminatingLAMP 2
12 3 4 5 6 7 8 (days)
Off At the time of power-on or menu setting
8.  Press the ENTER button.
•  When you select 24H
  or 1 WEEK , the box 
to set the lamp relay interval is displayed.  
24H 
NEXT LAMP RELAY
24H
0
OKCLEARDEL
CANCEL
123456789
←→
Lamp relay (continued)
1 WEEK 
NEXT LAMP RELAY
7D 00H
0
OKCLEARDEL
CANCEL
123456789
←→
9.  Move the key cursor using the direction buttons to 
select the number you want to enter and then press 
the ENTER button.
• Maximum interval
 24H  ........... 24H (24 hours)
 1 WEEK 
 .... 7D 00H (7 days and 00 hours)
 key:   Shifting the position of enter cursor 
to the left for each character.
 key:   Shifting the position of enter cursor 
to the right for each character.
 DEL key:   Deleting the character in the 
position of enter cursor for each 
character.
 CLEAR 
key:  Deleting all the entered characters.
•  You can enter the value by pressing the number 
buttons (0 to 9) while holding down the NUM 
button on the remote control. 
•  When the value you entered meets the following 
conditions, an error dialog box is displayed at 
the screen center. 
 ∙  The value has been cleared by DEL or CLEAR 
and left blank. 
 ∙  The value you entered is out of the setting 
range.
   24H 
  .........  25H or over
   1 WEEK 
  ...  7D 01H or over
 ∙  The value of each item is out of the setting 
range.
    D ..................  8 or over (1 WEEK 
 only)
    H ..................  25 or over
10. When selecting OK, the setting is completed as 
the lamp-switching interval stored. However, when 
selecting CANCEL, the setting is completed without 
storing.
•  The display returns the LAMP RELAY menu after 
selecting OK or CANCEL.
•  The setting you made is applied to NEXT LAMP 
RELAY in the INFORMATION menu.
Important:
•  When you use the projector continuously, the lamp 
relay may not be performed on time due to errors of 
the clock function. 
•  Immediately after the power-on, during the lamp 
selection, or during the lamp relay operation, you 
cannot change the setting of LAMP SELECT and 
LAMP RELAY. 
•  In the case of continuous projection, the lamps may 
deteriorate earlier unless they are turned off for 1 
hour per week. 
•  When using this projector continuously for a long 
time of period, enable LAMP RELAY.
•  The brightness and color tint vary at the time of 
lamp switching. 
						

							EN-55
•  The image within the outer edges of the red 
frame is captured. 
•  The captured image is displayed in the REAL 
mode automatically.
CAPTURE : ENTER + ENTER
CANCEL : MENUCAPTURE : ENTER X2
CANCEL : MENU
12.Adjust the size of the image to be captured so that 
such image stays within the red frame. 
• Press the , ,  or  button to move the red 
frame.
• You can’t move the red frame outside the 
scr
een. 
• Press the MENU button to cancel the 
procedure.
CAPTURE : ENTER X2
CANCEL : MENU
13. Press the ENTER button twice.
• Image capture will start.
CAPTURE : ENTER X2
CANCEL : MENUCAPTURING IMAGE !
• When the image capture completes, the 
captured image will be displayed for 1 second. 
Important:
• You can’t change the new startup screen back to 
the original startup scr
een. (Even when you select 
RESET ALL in the FEATURE menu, the factory 
default screen isn’t available any longer.) When you 
want to change the startup screen again, capture 
another image.
• The captured image will be displayed from the 
next startup. If the captur
ed image isn’t displayed, 
make sure that the setting of SPLASH SCREEN in 
the INSTALLATION 2 menu isn’t OFF. (See page 
35.)
• When BACK COLOR in the INSTALLATION 2 
menu is set to IMAGE, the captur
ed image will be 
displayed while no signal is supplied. 
•  When no video signal is supplied, the projector 
takes some time to display the captured image. 
 
• Some images can’t be captured correctly because 
of their signal type. 
Advanced features
Changing the image displayed at the 
startup
You can display your desired image as the startup 
screen (or splash screen). By setting the menu, you 
can use such image instead of the background image 
that is displayed when no video signal is supplied.
Important:
• You can’t set IMAGE CAPTURE when PASSWORD 
FUNCTION in the FEATURE menu has been set to 
SPLASH ID SCREEN to enable the password lock.
• You can’t set IMAGE CAPTURE when the 
component video signal is inputted.
Setting procedure 
(See page 32 for menu setting.)  
1.  Press the COMPUTER button to select the image 
supplied to the COMPUTER/COMPONENT VIDEO 
IN terminal.
2.  Display your desired image.
3.  Display the INSTALLATION 2 menu.
4.  Select IMAGE CAPTURE by pressing the  or  
button.
5.  Press the ENTER button.
• The setting menu will be displayed.
INSTALLATION 2
CUSTOM IMAGE CAPTURE
SIZE BACK COLOR
CAPTUREGRAY
x1
1 12 2opt.
GO
Set the background color
(Set the background color only when you set the 
image size to x1 or x2.)
6.  Select BACK COLOR by pressing the  or  
button.
7.  Select your desired color for the background 
(GRAY, RED, GREEN, BLUE, BLACK, WHITE, 
RED50%, GREEN50%, or BLUE50%) by pressing 
the 
 or  button. 
Set the image size
8.  
Select SIZE by pressing the  or  button.
9.  Select x1, x2, or FULL by pressing the 
 or  
button. 
x1 x2 FULL
Capture the image
10. Select CAPTURE by pressing the  or  button.
11.Press the ENTER button.
• A red frame appears. (The size of the red frame 
is 320 x 240 pixels.) 
						

							EN-56
Password function
This projector is equipped with the password function 
that is designed for prevention of wrong operation by 
children and restriction on operation by other than 
specifi ed users. The password function has 3 modes 
as follows.
DISPLAY INPUT .......... When the projector is turned 
on, the startup screen (or splash screen) will appear 
and stay on the screen until the password is 
entered. When the password is entered, the startup 
screen will switch to the regular operation screen.
MENU ACCESS ........... All the buttons except for the 
POWER button on the projector are disabled. (The 
buttons on the remote control are enabled.) You 
can use this mode as a measure of prevention 
of wrong operation by children and restriction on 
operation by other than specifi ed users.
SPLASH ID SCREEN ... IMAGE CAPTURE and 
SPLASH SCREEN in the INSTALLATION 2 menu 
become unavailable. SPLASH SCREEN will be set 
to ON automatically.
To enable the password function:
1.  Display the FEATURE menu.
2. Press the  or  button to select PASSWORD 
FUNCTION.
3. Press the  or  button to change the mode 
among DISPLAY INPUT 
, MENU ACCESS  and 
SPLASH ID SCREEN 
.
•  When the password has already been set, the 
mode won’t be changed. In such cases, press 
the ENTER button to cancel the password 
function and try again. 
4.  Press the ENTER button.
•  The screen for setting the password function will 
appear. 
FEATURE
DISPLAY INPUT
12opt.
LOCK
UNLOCK
12
ENTER
ENTER
5.  Press the ENTER button.
•  The screen for entering a password will appear. 
PASSWORD
CONFIRM
1
32 4
O K : ENTER CANCEL : MENU
6.  Enter a 4 - 8 digit password using the , ,  and 

 buttons.
 (
=1, =2, =3, =4) 
•  You can enter the value by pressing the number 
buttons (1 to 4) while holding down the NUM 
button on the remote control. 
Advanced features (continued)
7.  Press the ENTER button.
•  To cancel the procedure, press the MENU 
button. 
8.  Enter the password again for confi rmation using the 
same steps.
9.  Press the ENTER button. 
•  If the entered passwords don’t match, an error 
message will appear. 
•  To cancel the procedure, press the MENU 
button. 
To cancel the password function: 
1.  Display the FEATURE menu.
2. Press the  or  button to select PASSWORD 
FUNCTION.
3.  Press the ENTER button.
•  The screen for canceling the password function 
will appear.
FEATURE
DISPLAY INPUT
12opt.
LOCK
UNLOCK
12
ENTER
ENTER
4.  Press the ENTER button.
•  The screen for entering the password will 
appear. 
PASSWORD
1 
32  4 
O K : ENTER CANCEL : MENU
5.  Enter a 4 - 8 digit password using the , ,  and 

 buttons.
 (
=1, =2, =3, =4) 
•  You can enter the value by pressing the number 
buttons (1 to 4) while holding down the NUM 
button on the remote control. 
6.  Press the ENTER button.
•  If you enter a wrong password, an error 
message will appear.
•  To cancel the procedure, press the MENU 
button. 
Important:
•  Disable the password by pressing the MENU and 
ENTER buttons on the projector at the same time. 
						

							EN-57
Picture in Picture (PinP) 
One of the special features of this projector is the 
picture-in-picture (PinP) mode. The PinP mode allows 
you to view the images from different sources at the 
same time. 
•  While viewing the image from the COMPUTER1, 
COMPUTER2, DVI, or HDMI input source, you can 
display the image from the VIDEO or S-VIDEO input 
source as a sub image.
Sub image
To use the PinP mode
1.  Press the PinP button on the remote control. 
2.  If necessary, select the desired external input 
source of the sub image by using the VIDEO or 
S-VIDEO button on the remote control.
3.  Press the PinP button again to exit the PinP mode.
To change the position of the sub image:
Press the  or  button on the remote control.
Important:
•  The PinP mode is available only when the ASPECT 
ratio is set to NORMAL. 
•  The PinP mode isn’t available with some input 
signals. For further information, see page 73. 
•  When the main image signal is lost during the PinP 
mode, the PinP mode is disabled. 
•  When the COMPUTER 1, COMPUTER 2, DVI-D 
(HDCP) or HDMI button on the remote control is 
pressed, the PinP mode will be canceled. 
•  When there is no video signal for sub image, you 
can’t change the display position.
•  The motion may not run smoothly in the PinP 
mode.
•  You cannot make the MULTI-SCREEN menu 
settings and SIGNAL menu settings in the PinP 
mode. 
•  The size of the sub image varies depending on the 
input signal and the settings.
Advanced features (continued)
Magnifying the displayed image
By pressing the MAGNIFY button on the remote 
control, you can magnify the image to view the details.
•  While viewing the image from the COMPUTER1, 
COMPUTER2, DVI, or HDMI input source, you can 
magnify the image.
Magnifi ed image
To use the MAGNIFY mode:
1.  Press the MAGNIFY button on the remote control. 
•  You can select the area to be magnifi ed by 
pressing the , ,  or  button on the 
remote control.
•  You can change the magnifi cation of the 
selected area by pressing the + or - button.
2.  Press the MAGNIFY button again to exit the 
MAGNIFY mode.
•  The regular operation screen will appear.
Important:
•  The MAGNIFY mode doesn’t function with some 
input signals. For details, see page 73.
•  In the MAGNIFY mode, you can’t display the MULTI-
SCREEN menu and the SIGNAL menu.
Freeze
To stop the motion in the image temporarily (or to 
display a still image):
Press the FREEZE button on the remote control.
•  The image will freeze temporarily.
To resume the motion in the image:
Press the FREEZE button on the remote control again.
Important:
•  Do not display a still picture for a long time 
because the afterimages may persist on the screen.  
						

							EN-58
Important:
•  When you set CONTROL SYSTEM to CRESTRON 
in the NETWORK menu, the web control for 
Crestron is enabled. For such control, Adobe Flash 
Player should be installed in advance. You can 
download Adobe Flash Player from the website of 
Adobe Systems Incorporated.
•  When you set CONTROL SYSTEM to CRESTRON 
in the NETWORK menu, you cannot use the control 
by ProjectorView Global+, which is the software 
supplied with the projector. 
About PJLink™
•  To use PJLink™ function, the PJLink™ 
application software is required. 
•  To use this function, set the network certifi cation 
properly according to the setting of the network 
application to be used. (See page 51.)
•  For the specifi cations of PJLink™, access to 
the Web site of Japan Business Machine and 
Information System Industries Association 
(JBMIA). (http://pjlink.jbmia.or.jp/english)
•  This projector is fully compliant to the 
specifi cations of JBMIA PJLink™ Class 1. It 
supports all the commands defi ned by PJLink™ 
Class 1, and the compliance has been verifi ed 
with the PJLink™ standard specifi cations 
Version 1.0.
Important:
•  For the commands for PJLink™, see the table on 
the next page.
• The control may not be performed correctly or the 
monitoring data may not be obtained corr
ectly in 
the following conditions:
· During standby
· During zoom/focus adjustment
· During lens shift adjustment
· During input source switching
· During auto position execution
· During BLANK
· During command processing
· Before the splash screen disappears after the 
power is turned on.
• During zoom/focus adjustment, lens shift 
adjustment, BLANK, etc., it may take approx. 5 
seconds to receive a response to a command. 
• Use 1 controller to control/monitor 1 projector. 
• For how to control/monitor using PJLink™, see the 
operation manual of the PJLink™ application you 
use. 
•  When you monitor the projector’s operating state 
using this function by issuing inquiry commands 
successively, issue an inquiry command after 
receiving the response to the previous inquiry 
command from the projector.
 
Supervising and controlling by computer
You can supervise and control the projector’s 
operation using a personal computer via a LAN 
network. 
Major functions
ProjectorView Global+
Batch projector controlling / supervising application 
software
•  Batch operation of stand-alone projector / multiple 
projectors
•  Scheduling function to turn ON/OFF for each day of 
the week
•  Checking each condition of the projector and 
detecting a theft
•  Setting of the projector’s IP CONFIG
•  Startup of the controlling / supervising tool 
(ProjectorView) using the Web browser
•  Activating Visual PA2 to display the specifi ed 
characters on the projector’s screen
•  Projector’s Text Speech function to read aloud 
messages displayed on the Visual PA2 window
ProjectorView
The controlling /supervising tool using the Web 
browser 
AMX Device Discovery
The projector is monitored and controlled by the 
controller system of AMX.
Crestron Roomview™ Connected
The projector is monitored and controlled by the controller 
system and software of Crestron Electronics, Inc.
PJLink™
This projector supports standard protocol PJLink™ 
for projector control and you can control and monitor 
projector’s operations using the same application 
among projectors of different models and different 
manufacturers. 
About ProjectorView Global+
•  For details, see “LAN control UTILITY operation 
manual” in the CD-ROM.
About AMX Device Discovery
•  This is a technology suggested by AMX to 
facilitate confi guration of the control system 
of AMX and its target devices. To use this 
technology, it is necessary to set CONTROL 
SYSTEM in the NETWORK menu. (See pages 40 
and 51.)
  For details, see the website of AMX. 
 URL http://www.amx.com/
About Crestron RoomView™ Connected
•  This is a technology suggested by Crestron 
Electronics, Inc. to facilitate confi guration of the 
control system of Crestron and its target devices. 
To use this technology, it is necessary to set 
CONTROL SYSTEM in the NETWORK menu. 
(See pages 40 and 51.)
  For details, see the website of Crestron 
Electronics, Inc.
 URL http://www.crestron.com
 URL http://www.crestron.com/getroomview/
Advanced features (continued) 
						

							EN-59
Connection
For details of the connection, see “LAN control UTILITY operation manual” in the CD-ROM.
When STANDBY MODE of the INSTALLATION 1 menu of the projector is set to LOW, the LAN network is disabled. 
To enable the LAN network, set STANDBY MODE to STANDARD. (See page 34 .)
Confi gure the initial network settings fi rst. 
You can confi gure the initial settings using the projector menu (see pages 49 to 52) or ProjectorView Global+. For 
details of ProjectorView Global+, see “LAN control UTILITY operation manual” in the CD-ROM.
Using the User Manual
The User Manual for LAN Control Utility is prepared in the Portable Document Format (PDF) in the CD-ROM. 
Opening the User Manual:
1.  Load the CD-ROM into the CD-ROM drive.
2.  Open CD-ROM “PROJECTOR.”
3.  Double-click on “MANUAL_LAN.HTML” within the CD-ROM. A language selection list for the User Manual will be 
displayed.
4.  Move the mouse pointer to the desired language and click. 
PJLink™ supported commands
The table below shows commands to control the projector using the PJLink™ protocol.
Command Description Remark (Parameter)
POWR Power control 0 = Standby
1 = Power on
POWR? Inquiry about the power state 0 = Standby
1 = Power on
2 = Cooling down
3 = Warming up
INPT Input switching 11 = COMPUTER1  12 = COMPUTER2
21 = VIDEO  22 = S-VIDEO
31 = HDMI  32 = DVI INPT? Inquiry about input switching
AVMT Mute control 30 = Video mute disable
31 = Video mute enable
AVMT? Inquiry about the mute state
ERST? Inquiry about the error state 1st byte: Fan error, 0 or 2
2nd byte: Lamp error, 0 to 2
3rd byte: Temperature error, 0 or 2
4th byte: Cover open error, 0 or 2
5th byte: Always 0
6th byte: Other error, 0 or 2
0 to 2 mean as follows: 
0 = No error detected, 1 = Warning, 2 = Error
LAMP? Inquiry about the lamp state
1st value (1 to 5 digits):  Cumulative LAMP 1 operating time (This item 
shows a lamp operating time (hour) calculated 
based on that LAMP MODE is LOW.)
2nd value: 0 = Lamp off, 1 = Lamp on3rd value (1 to 5 digits):  Cumulative LAMP 2 operating time (This item 
shows a lamp operating time (hour) calculated 
based on that LAMP MODE is LOW.)
4th value: 0 = Lamp off, 1 = Lamp on
INST? Inquiry about the available inputs The following value is returned.
“11 12 21 22 31 32”
NAME? Inquiry about the projector name The projector name set on the NETWORK menu or the ProjectorView 
Setup window is returned. 
INF1? Inquiry about the manufacturer name “MITSUBISHI” is returned. 
INF2? Inquiry about the model name “XD8100U” is returned. 
INF0? Inquiry about other information No other information is available. No parameter is returned.
CLSS? Inquiry about the class information “1” is returned.
•  This projector is fully compliant to the specifi cations of JBMIA PJLink™ Class 1. It supports all the commands defi ned by 
PJLink™ Class 1, and the compliance has been verifi ed with the PJLink™ standard specifi cations Version 1.0.
Advanced features (continued) 
						

							EN-60
Monitoring and control using SERIAL terminal
Using the SERIAL terminal, you can monitor and control multiple projectors collectively or individually. 
•  For details, contact your dealer. 
To RS-232C terminal
To SERIAL 
INTo SERIAL 
INTo SERIAL 
IN To SERIAL 
OUTTo SERIAL 
OUT RS-232C cable RS-232C cable
•  See also the instruction manuals of the devices to 
be connected. 
Connection
•  Make sure that the power supplies of the projector 
and the computer are off. 
1.  Connect one end of an RS-232C cable to 
the SERIAL IN terminal on the projector to be 
connected to the computer. 
2.  Connect the other end of the RS-232C cable to the 
serial port on the computer. 
3.  Connect one end of an RS-232C cable to the 
SERIAL OUT terminal on the projector that is 
connected to the computer. 
4.  Connect the other end of the RS-232C cable to the 
SERIAL IN terminal on the second projector. 
•  For the connection of the second and later 
projectors, connect their SERIAL OUT terminals 
and the SERIAL IN terminals using RS-232C 
cables.
Important:
•  In a system using a serial divider, don’t connect the 
projectors as above. 
To monitor and control the projectors collectively or 
individually, it is necessary to assign PROJECTOR IDs 
or GROUP IDs to them.
Setting PROJECTOR IDs
You can monitor and control multiple projectors 
individually. 
PROJECTOR IDs should be two-digit numbers “01” to 
“63” or “ALL.” The other numbers cannot be used. 
•  The default PROJECTOR ID is ALL. 
•  By assigning the same PROJECTOR ID to multiple 
projectors, you can monitor and control those 
projectors collectively. 
Advanced features (continued)
(See page 32 for menu setting.)
1.  Display the FEATURE menu. 
2.  Select PROJECTOR ID by pressing the   or  
button. 
PROJECTOR ID
ALL
3.  Set the PROJECTOR ID by pressing the   or  
button. 
Important:
•  To monitor and control the projectors individually, 
assign different PROJECTOR IDs to them. 
•  By assigning ALL, you can monitor and control the 
projectors regardless of the ID numbers. 
Setting GROUP IDs
By dividing the projectors into groups, you can monitor 
and control them collectively by groups. 
GROUP IDs should be A to Z. You can create up to 26 
groups.
•  The default GROUP ID is A. 
(See page 32 for menu setting.)
1.  Display the FEATURE menu. 
2.  Select GROUP ID by pressing the   or  button. 
A GROUP ID
3.  Set the GROUP ID by pressing the   or  button. 
Important:
•  When you want to monitor and control the 
projectors by groups, set a different GROUP ID.
•  For details, contact your dealer.