Mitsubishi Xd8100lu Projector User Manual

EN-41
INFORMATION menu
60.00 Hz RESOLUTION
1024 x 768
VERTICAL
FREQUENCY
48.36 kHz
5WIRE HORIZONTAL
FREQUENCY
SYNC. TYPE SERIAL NUMBER
INFORMATION1 12 2
FILTER TIME*****H / ****TIMES
********... NEXT LAMP RELAY
COMPUTER1 INPUT
opt.
*D **H 
RG
HVB
LAMP 1 TIME (LOW)
LAMP 2 TIME (LOW)
****H****H
ITEM DESCRIPTION
LAMP 1 TIME (LOW)
This item shows the lamp operation time calculated based on that the LAMP MODE of LAMP 1 
is LOW.  
•  When the LAMP MODE is STANDARD, this item shows a longer lamp operating time...

EN-42
Adjusting projected images
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu. 
(See page 32 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select CONTRAST or BRIGHTNESS by pressing the  or  button. 
3.  Adjust the selected item by pressing the  or  button. 
To cancel the menu:
4.  Press the MENU button. 
CONTRAST 
Select to adjust the contrast of the image. Every time the  button is pressed, the image...

EN-43
To cancel the menu:
7.  Press the MENU button. 
To enable the stored color temperature: 
1.  Set COLOR TEMP. to USER 
 in the IMAGE menu. 
About color temperature
Color temperature is a way to show the differences in white. White of which temperature is low appears reddish. 
When the color temperature rises, white appears bluish. For example, you can change the color temperature using 
the following procedures. 
To raise the color temperature: Increase the CONTRAST B (blue) and decrease the...

EN-44
Adjusting the fi neness of the image (SUPER RESOLUTION): 
You can adjust the fi neness of the image using the menu.  
(See page 32 for menu setting.) 
With the IMAGE menu:
1.  Display the IMAGE menu. 
2.  Select SUPER RESOLUTION by pressing the  or  button. 
3. Press the  or  button to select ON 
. 
4.  Press the ENTER button.
5.  Make adjustment using the  or  button.  
Important:
• When you make SUPER RESOLUTION adjustment, the colors of the menu may be obscured, but this is not a 
failure....

EN-45
Adjusting projected images (continued)
How to adjust the computer image
This projector automatically selects a proper signal format according to the type of video signal supplied from the 
computer. However, video signals from the computer may not be projected correctly depending on the types of the 
computer and images to be projected. In such a case, make adjustment according to the fl owchart below.
Adjustment is completed. When the size and position of 
the computer image are not correct....

EN-46
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms. 
Wide strips appear.  ……………………………………… Adjust TRACKING in the SIGNAL menu. 
The projected image fl ickers. 
The projected image is blurred. ......................................Adjust FINE SYNC. in the SIGNAL menu. 
The projected image is displaced horizontally. ..............Adjust HORIZ.POSITION in the SIGNAL menu. Every time the 
 button is pressed, the image moves to...

EN-47
12. Select an item you want to set by pressing the  or 
 button.
•  Adjust the black level in areas other than the 
overlapped areas. 
•  When you set INTERLOCKED to ON, you can 
adjust RED, GREEN, and BLUE simultaneously. 
When you set it to OFF, you can adjust RED, 
GREEN, and BLUE separately. 
13. Select a setting value by pressing the  or  
button. 
Repeat steps 12 to 13, if necessary. 
14. Press the MENU button once. 
15. Select BRIGHT UNIFORMITY CORRECTION 
 by 
pressing the  or ...

EN-48
7.  Select an item you want to set by pressing the  or 
 button.
•   Select the color you want to adjust using 
COLOR.
8.  Select a setting value by pressing the  or  
button.
•  You can enter numbers by pressing the number 
buttons (0 to 9) while holding down the NUM 
button on the remote control. 
Repeat steps  7 to 8, if necessary. 
Important:
•  The color tone may not be displayed correctly 
depending on the setting value. Set the value within 
the proper range.
Set the target values of the...

EN-49
Initial network settings
You can set the network of the projector using the 
menu.
NETWORK CONTROLLER
NETWORK PASSWORD
NETWORK1 12 2
NETWORK CERTIFICATION PROJECTOR NAME
IP CONFIG
NETWORK RESET
opt.
STANDARD
ENTER
ENTER
OK
ON
Setting Projector Name
(See page 32 for menu setting.)
1.  Display the NETWORK menu. 
2. Press the  or  button to select PROJECTOR 
NAME.
PROJECTOR NAMESET
3. Press the  or  button to select SET .
4.  Press the ENTER button.
•  PROJECTOR NAME screen appears.
PROJECTOR...

EN-50
6.  Enter the NEW NETWORK PASSWORD and 
CONFIRM NETWORK PASSWORD.
•  Password can be set using up to 32 characters 
including alphabets (capital/small) or numeric 
characters.
 key: ............. Shifting the position of enter 
cursor to the left for each 
character.
 key: ............. Shifting the position of enter 
cursor to the right for each 
character.
 key: ...............  Shifting the position of 
enter cursor between NEW 
NETWORK PASSWORD 
and CONFIRM NETWORK 
PASSWORD.
DEL key:...