Mitsubishi Xd8100lu Projector User Manual

							EN-41
INFORMATION menu
60.00 Hz RESOLUTION
1024 x 768
VERTICAL
FREQUENCY
48.36 kHz
5WIRE HORIZONTAL
FREQUENCY
SYNC. TYPE SERIAL NUMBER
INFORMATION1 12 2
FILTER TIME*****H / ****TIMES
********... NEXT LAMP RELAY
COMPUTER1 INPUT
opt.
*D **H 
RG
HVB
LAMP 1 TIME (LOW)
LAMP 2 TIME (LOW)
****H****H
ITEM DESCRIPTION
LAMP 1 TIME (LOW)
This item shows the lamp operation time calculated based on that the LAMP MODE of LAMP 1 
is LOW.  
•  When the LAMP MODE is STANDARD, this item shows a longer lamp operating time than 
the actual time.
•  When the lamp operating time is 0 to 10 hours, “0H” is displayed. The lamp operating time 
exceeding 10 hours is indicated by the actual hours. 
•  When the lamp operating time reaches 3000 hours, the bar turns to yellow.  When it 
reaches 3800 hours, the bar turns to red.  
•  The icon displayed to the right of the bar shows the lamp status. 
  Yellow: On, Red: End of lamp life or error such as illumination failure, Black: Off
LAMP 2 TIME (LOW)
This item shows the lamp operation time calculated based on that the LAMP MODE of LAMP 2 
is LOW.  
•  When the LAMP MODE is STANDARD, this item shows a longer lamp operating time than 
the actual time.
•  When the lamp operating time is 0 to 10 hours, “0H” is displayed. The lamp operating time 
exceeding 10 hours is indicated by the actual hours. 
•  When the lamp operating time reaches 3000 hours, the bar turns to yellow.  When it 
reaches 3800 hours, the bar turns to red.  
•  The icon displayed to the right of the bar shows the lamp status. 
  Yellow: On, Red: End of lamp life or error such as illumination failure, Black: Off
NEXT LAMP RELAY
The next lamp relay time is displayed. 
FILTER TIME
The fi lter operation time and the cleaning count are displayed. 
SERIAL NUMBER
The serial number of the projector is displayed. 
INPUT
Indicates the name of the terminal to which the currently projected video signal is being input.
RESOLUTION
Indicates the resolution of the currently projected video signal. 
VERTICAL FREQUENCY
Indicates the vertical frequency of the currently projected video signal. 
HORIZONTAL FREQUENCY
Indicates the horizontal frequency of the currently projected video signal. 
SYNC. TYPE
Indicates the type of the sync signal for the currently projected video signal. 
•  NEXT LAMP RELAY isn’t displayed when LAMP RELAY is OFF or LAMP SELECT is LAMP 1 or LAMP 2 in the INSTALLATION 
1 menu. 
Menu operation (continued) 
						

							EN-42
Adjusting projected images
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu. 
(See page 32 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select CONTRAST or BRIGHTNESS by pressing the  or  button. 
3.  Adjust the selected item by pressing the  or  button. 
To cancel the menu:
4.  Press the MENU button. 
CONTRAST 
Select to adjust the contrast of the image. Every time the  button is pressed, the image becomes brighter and more 
defi ned. Every time the  button is pressed, the image becomes darker and less defi ned.
BRIGHTNESS
Every time the  button is pressed, the image becomes brighter. Every time the  button is pressed, the image 
becomes darker. 
To adjust the color (COLOR and TINT):
You can adjust the color of the projected image using the menu. 
(See page 32 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select COLOR or TINT by pressing the  or  button.  
•  COLOR or TINT is unavailable when COMPUTER1, COMPUTER2, DVI or HDMI is selected as the input source.
•  TINT is available only when the NTSC signal is input. 
3.  Adjust the selected item by pressing the  or  button. 
To cancel the menu:
4.  Press the MENU button. 
COLOR 
Use to adjust the color thickness of the projected image. Every time the  button is pressed, the color becomes 
thicker. Every time the  button is pressed, the color becomes lighter. 
TINT
Use to adjust the tint of the projected image. Every time the  button is pressed, the image appears more greenish.
Every time the  button is pressed, the image appears more reddish. 
To sharpen or soften the projected image (SHARPNESS):
You can adjust the sharpness of the projected image using the menu. 
(See page 32 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select SHARPNESS by pressing the  or  button. 
3.  Adjust the selected item by pressing the  or  button. 
To cancel the menu:
4.  Press the MENU button. 
To adjust the tone of white (COLOR TEMP.): 
You can select a preset color temperature (white tone) using the menu. 
(See page 32 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select COLOR TEMP. by pressing the  or  button. 
3.  Select your desired color temperature by pressing the  or  button. 
To cancel the menu:
4.  Press the MENU button. 
To adjust the tone of white (To customize the color temperature): 
To customize (and store) the color temperature to your preference, carry out the following procedure. 
(See page 32 for menu setting.) 
1.  Select COLOR TEMP. in the IMAGE menu. 
2. Press the  or  button to select USER 
. 
3.  Press the ENTER button.
4. Press the  or  button to select the desired item. 
5. Press the  or  button to adjust the selected item. 
6.  Repeat steps 4 and 5 for optimum adjustment results.COLOR TEMP.–USER
CONTRAST R
CONTRAST G
CONTRAST B
BRIGHTNESS R
0
BRIGHTNESS G
0
BRIGHTNESS B0
0
0
0 
						

							EN-43
To cancel the menu:
7.  Press the MENU button. 
To enable the stored color temperature: 
1.  Set COLOR TEMP. to USER 
 in the IMAGE menu. 
About color temperature
Color temperature is a way to show the differences in white. White of which temperature is low appears reddish. 
When the color temperature rises, white appears bluish. For example, you can change the color temperature using 
the following procedures. 
To raise the color temperature: Increase the CONTRAST B (blue) and decrease the CONTRAST R (red).
To reduce the color temperature: Decrease the CONTRAST B (blue) and increase the CONTRAST R (red).
•  If you set all of CONTRAST R, G, and B to negative values, the original brightness of the image can’t be 
obtained even when you maximize CONTRAST in the IMAGE menu. 
Color Enhancer
You can set the user-defi ned balance between the brightness and hue using the menu. 
(See page 32 for menu setting.)
With the IMAGE menu:
1.  Display the IMAGE menu.
2.  Select COLOR ENHANCER by pressing the  or  button.
3. Select USER 
 or MULTI-SCREEN  by pressing the  or  button.
Important:
•  You can set MULTI-SCREEN only when EDGE BLENDING is ON or COLOR 
MATCHING is MANUAL or MEASURE in the MULTI-SCREEN menu. 
4.  Press the ENTER button.
•  The detailed menu for the color enhancer is displayed. 
5.  Select an item you want to set by pressing the  or  button.
GAMMA mode
Use this item to set the gamma optimally.
When USER is selected: 
DYNAMIC ……Select when viewing images supplied from the computer.
NA
TURAL
 ……Select when viewing images supplied from the video device.
DETAIL
 ………Select when viewing images of which brightness should be kept relatively low, such as movies and 
music performance.
When MULTI-SCREEN is selected:
•  1.8/2.0/2.2  Select the gamma characteristics from 1.8th, 2.0th, and 2.2nd power. 
BrilliantColor™
Use this item to make the colors having medium brightness such as yellow and skin tone look natural. Press the  
button to decrease the value to lessen the effect. Press the  button to increase the value to heighten the effect.
(BrilliantColor™ doesn’t work at value 0.)  
6. Select a setting value by pressing the  or  button. 
•  For more enhanced color reproduction, set BrilliantColor™ to 0. The white portion of the color wheel will be 
disabled and you can reproduce true-to-life images.
Important:
•  You can adjust Color Enhancer also by pressing the CE button on the remote control. 
With the remote control:
1.  Press the CE button on the remote control. 
  A window for color enhancer adjustment appears on the upper right of the screen. 
2. Press the  or  button to select USER 
 or MULTI-SCREEN .
3.  Press the ENTER button.
4. Press the  or  button to select GAMMA MODE or BrilliantColor™. 
5. Press the  or  button to adjust the selected item. 
COLOR ENHANCERAUTO
Adjusting projected images (continued)
COLOR ENHANCER–USER
GAMMA MODE DYNAMIC
BrilliantColorTM10
When USER is selected:
COLOR ENHANCER–MULTI-SCREEN
GAMMA MODE 2.0
BrilliantColorTM0
When MULTI-SCREEN is selected: 
						

							EN-44
Adjusting the fi neness of the image (SUPER RESOLUTION): 
You can adjust the fi neness of the image using the menu.  
(See page 32 for menu setting.) 
With the IMAGE menu:
1.  Display the IMAGE menu. 
2.  Select SUPER RESOLUTION by pressing the  or  button. 
3. Press the  or  button to select ON 
. 
4.  Press the ENTER button.
5.  Make adjustment using the  or  button.  
Important:
• When you make SUPER RESOLUTION adjustment, the colors of the menu may be obscured, but this is not a 
failure. 
•  You can adjust SUPER RESOLUTION also by pressing the SUPER RESOLUTION button on the remote control. 
With the remote control:
1.  Press the SUPER RESOLUTION button on the remote control. 
  A window for SUPER RESOLUTION adjustment appears on the upper right of the screen. 
2. Press the  or  button to select ON 
. 
3.  Press the ENTER button.
4.  Make adjustment using the  or  button.  
Adjusting the tone of each color (NCM): 
You can adjust the tone of each color using the menu.  
(See page 32 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select NCM by pressing the  or  button. 
3. Press the  or  button to select USER 
. 
4.  Press the ENTER button.
5. Select an item you want to set using the   or  button. 
•  If you want to adjust the saturation of all colors of the image, select 
SATURATION. 
•  If you want to adjust the balance of all colors of the image, select RGB-TINT.
6. Press the  or  button to adjust the color balance of the selected color.
7.  Repeat steps 5 and 6 for optimum adjustment results.
• When the input signal is VIDEO or COMPUTER, the items in the NCM-USER menu are automatically set to the 
predetermined values. You can change these values manually. 
• To cancel the NCM-USER menu, select OFF in step 2. 
• When you make NCM adjustment, the colors of the menu will change, but this is not a failure. 
Adjusting projected images (continued)
SUPER RESOLUTIONON
SUPER RESOLUTION
LEVEL 1
NCMCOMPUTER
NCM−USER
RED
YELLOW
GREEN
CYAN0
0
0
0
BLUE
MAGENTA
SATURATION0
RGB-TINT
0 0
0 
						

							EN-45
Adjusting projected images (continued)
How to adjust the computer image
This projector automatically selects a proper signal format according to the type of video signal supplied from the 
computer. However, video signals from the computer may not be projected correctly depending on the types of the 
computer and images to be projected. In such a case, make adjustment according to the fl owchart below.
Adjustment is completed. When the size and position of 
the computer image are not correct. 
Project a bright computer image containing as many texts and characters as possible.
Note) Disable the screen saver if it is active.
Press the AUTO POSITION button. 
Settings are automatically and optimally adjusted for the input signal.
Image is projected 
correctly.
YESNO
Display the screen resolution setting menu of your computer. 
(Example: In the case of Windows
® PC, right-click on the desktop, select Properties, and click the 
Settings tab to display the screen resolution setting.)
The screen 
resolution setting of your computer 
is different from the setting of RESOLUTION 
(MEMORIZE    ) in the SIGNAL menu 
of the projector. 
Select RESOLUTION (MEMORIZE    ) in the SIGNAL menu 
and press the ENTER button.
Set HORIZ. PIXELS and VERT. LINES to the values of the screen resolution of your computer. 
(Example: When the screen resolution of the computer is 1280x800, set HORIZ. PIXELS to 1280 and 
VERT. LINES to 800.)
Select EXECUTE and press the ENTER button.
Automatic adjustment starts according to the selected resolution.
Image is projected 
correctly.
Perform manual 
adjustment. 
After the memory saving 
massage is displayed, 
select MEMORY 1 or 
MEMORY 2 and press the 
ENTER button.After the memory saving 
massage is displayed, 
select MEMORY 1 or 
MEMORY 2 and press the 
ENTER button.When you don’t save 
the adjustment result, 
press the MENU button.
Adjustment is canceled.
Adjust HORIZ. POSITION, VERT. POSITION, and TRACKING 
in the SIGNAL menu. For details, see “Simple method to 
adjust the image position.” (See page 46.) YESNO
YESNO YESNO 
						

							EN-46
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms. 
Wide strips appear.  ……………………………………… Adjust TRACKING in the SIGNAL menu. 
The projected image fl ickers. 
The projected image is blurred. ......................................Adjust FINE SYNC. in the SIGNAL menu. 
The projected image is displaced horizontally. ..............Adjust HORIZ.POSITION in the SIGNAL menu. Every time the 
 button is pressed, the image moves to the right. Every time 
the  button is pressed, the image moves to the left. 
The projected image is displaced vertically....................Adjust VERT.POSITION in the SIGNAL menu. Every time the  
button is pressed, the image moves down. Every time the  
button is pressed, the image moves up. 
The top part of the image fl ags. .....................................Change the setting of HOLD in the SIGNAL menu. Select ON , 
press the ENTER button, and adjust BEGIN or END to minimize 
the fl agging.
A solid black or solid white appears in the image.  ........ Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL 
- USER menu.
The motion doesn’t run smoothly. ..................................Adjust VERT. SYNC. in the SIGNAL - USER menu. Select 
AUTO for normal use. 
Noise appears on the right or left half of the image.
 ......Adjust SHUTTER(LS) or SHUTTER(RS) in the SIGNAL - USER 
menu.
Noise appears on the top or bottom part of the image.
 .......Adjust SHUTTER(U) or SHUTTER(L) in the SIGNAL - USER 
menu.
1.  Display the SIGNALmenu. 
2. Pr
ess the  or  button to select an item to adjust. 
3.  Adjust the selected item by pressing the  or  button. 
To cancel the menu:
4.  Press the MENU button. 
•  Do not change the settings of the SIGNAL menu in normal use. 
Simple method to adjust the image position
To adjust the horizontal position: 
1.  Align the left edge of the image with the left side of the screen by adjusting HORIZ.POSITION. Then, align the 
right edge of the image with the right side of the screen by adjusting TRACKING. 
2.  Repeat step 1 above to complete the adjustment of the horizontal position. 
To adjust the vertical position: 
3.  Align the upper edge of the image with the upper side of the screen by adjusting VERT.POSITION. 
LPF (Progressive fi lter) 
You can select whether or not to enable the LPF. 
Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD player or 
game console you use. In such a case, you can reduce such streak noise by enabling the LPF. However, projected 
images become softened slightly. 
Adjusting projected images (continued) 
						

							EN-47
12. Select an item you want to set by pressing the  or 
 button.
•  Adjust the black level in areas other than the 
overlapped areas. 
•  When you set INTERLOCKED to ON, you can 
adjust RED, GREEN, and BLUE simultaneously. 
When you set it to OFF, you can adjust RED, 
GREEN, and BLUE separately. 
13. Select a setting value by pressing the  or  
button. 
Repeat steps 12 to 13, if necessary. 
14. Press the MENU button once. 
15. Select BRIGHT UNIFORMITY CORRECTION 
 by 
pressing the  or  button. 
•  When EDGE BLENDING is ON, the brightness of 
the projected images is made even.
SETTINGBRIGHT UNIFORMITY
CORRECTION
16. Press the ENTER button.
•  The BRIGHT UNIFORMITY CORRECTION 
dialog box and the correction position marker 
are displayed. 
POSITION : SELECT : ENTER
Correction position marker BRIGHT UNIFORMITY CORRECTION dialog box
• Every time you press the ENTER button, the 
BRIGHT UNIFORMITY CORRECTION dialog box 
shows POSITION and LEVEL alternately. 
POSITION
POSITION : 
SELECT : ENTER Press the , , , or  
button to move the correction 
position marker.
LEVEL
 
LEVEL :  100
SELECT : ENTERPress the , or  button to 
adjust the correction amount. 
17. Cancel the BRIGHT UNIFORMITY CORRECTION 
dialog box. 
  Press any button other than the , , , or , 
and ENTER buttons to clear the dialog box.
  Or, the dialog box disappears in 10 seconds after 
the last use.
To cancel the menu:
18. Press the MENU button. 
Adjusting projected images (continued)
Adjusting the image displayed on 
the multi-screen
You can confi gure a multi-screen display using 
multiple projectors. 
You can make the joints of the images displayed on 
the projectors unnoticeable and adjust the differences 
in the brightness and the color tint of them. 
Making the joints unnoticeable 
You can make the joints of the images projected on 
the projectors unnoticeable using the menu settings. 
(See page 32 for menu setting.) 
1.  Display the MULTI-SCREEN menu. 
2.  Select EDGE BLENDING by pressing the  or  
button. 
EDGE BLENDING
OFF
3.  Select ON by pressing the  or  button. 
4.  Select SETTING by pressing the  or  button. 
SETTINGEDGE ADJUST
5.  Select EDGE ADJUST  by pressing the  or  
button. 
6.  Press the ENTER button.
SETTING - EDGE ADJUST
EDGE SELECT
BLENDING
WIDTH
MARKERUP
OFF
128
OFF
7.  Select an item you want to set by pressing the  or 
 button.
EDGE SELECT
  Select the joint you want to adjust from UP, LOW, 
LEFT, and RIGHT.
BLENDING
  When you select ON, the joint selected by EDGE 
SELECT becomes unnoticeable. 
WIDTH
  Set the width of the overlap of the joint selected by 
EDGE SELECT. 
  When UP or LOW is selected:   4 to 368
  When LEFT or RIGHT is selected:  4 to 496
MARKER
  When you select ON, a marker for easily locating 
the overlap of the joint is displayed.
8. 
Select a setting value by pressing the  or  button. 
Repeat steps 7 to 8, if necessary. 
9.  Press the MENU button once. 
10. 
Select BLACK LEVEL  by pressing the  or  
button. 
SETTINGBLACK LEVEL
11. Press the ENTER button.
SETTING - BLACK LEVEL
INTERLOCKED
RED
GREENON
0
0
BLUE
0 
						

							EN-48
7.  Select an item you want to set by pressing the  or 
 button.
•   Select the color you want to adjust using 
COLOR.
8.  Select a setting value by pressing the  or  
button.
•  You can enter numbers by pressing the number 
buttons (0 to 9) while holding down the NUM 
button on the remote control. 
Repeat steps  7 to 8, if necessary. 
Important:
•  The color tone may not be displayed correctly 
depending on the setting value. Set the value within 
the proper range.
Set the target values of the brightness and 
chromaticity coordinates:
4.  Select MEASURE by pressing the  or  button. 
MEASURED DATAMEASURE
5.  Select TARGET DATA  by pressing the  or  
button. 
6.  Press the ENTER button.
MEASURE – TARGET DATA
COLOR
GAIN
x
yRED
*.***
*.***
*.***AUTO PATTERN
ON
7.  Select an item you want to set by pressing the  or 
 button.
•  Select the color you want to adjust using 
COLOR.
•  When you set AUTO PATTERN to ON, the test 
pattern of each color is displayed. 
8.  Select a setting value by pressing the  or  
button.
•  You can enter numbers by pressing the number 
buttons (0 to 9) while holding down the NUM 
button on the remote control. 
Repeat steps  7 to 8, if necessary. 
Important:
• The color tone may not be displayed correctly 
depending on the setting value. Set the value within 
the proper range.
Resetting the settings
•  You can reset the SETTING, MANUAL, and 
MEASURE settings to the factory defaults. 
1.  Display the MULTI-SCREEN menu. 
2.  Select SETTING, MANUAL or MEASURE by 
pressing the  or  button. 
3. Select RESET 
 by pressing the  or  button. 
4.  Press the ENTER button.
Adjusting projected images (continued)
Adjusting the color variations
You can adjust the variations in the colors of the 
images displayed on multiple projectors using the 
menu settings. 
(See page 32 for menu setting.) 
Adjustment while viewing the screen
1.  Display the MULTI-SCREEN menu. 
2.  Select COLOR MATCHING by pressing the  or  
button. 
OFF COLOR MATCHING
3.  Select MANUAL by pressing the  or  button. 
4.  Select MANUAL by pressing the  or  button. 
MANUAL
SETTING
5. Select SETTING  by pressing the  or  button. 
6.  Press the ENTER button.
MANUAL – SETTING
COLOR
GAIN
SATURATION
HUERED
0
0
0
WHITE R
WHITE G
WHITE B- - -
AUTO PATTERN
ON - - -
- - -
7.  Select an item you want to set by pressing the  or 
 button.
•  Select the color you want to adjust using 
COLOR.
•  When you set AUTO PATTERN to ON, the test 
pattern of each color is displayed. 
8.  Select a setting value by pressing the  or  
button.
Repeat steps  7 to 8, if necessary. 
Adjustment using a chroma meter
1.  Display the MULTI-SCREEN menu. 
2.  Select COLOR MATCHING by pressing the  or  
button. 
OFF COLOR MATCHING
3.  Select MEASURE by pressing the  or  button. 
Set the measured brightness and the chromaticity 
coordinates:
4.  Select MEASURE by pressing the  or  button. 
MEASURED DATAMEASURE
5.  Select MEASURED DATA  by pressing the  or  
button. 
6.  Press the ENTER button.
MEASURE – MEASURED DATA
COLOR
Y (RELATIVE)
x
yRED
*****
*.***
*.*** 
						

							EN-49
Initial network settings
You can set the network of the projector using the 
menu.
NETWORK CONTROLLER
NETWORK PASSWORD
NETWORK1 12 2
NETWORK CERTIFICATION PROJECTOR NAME
IP CONFIG
NETWORK RESET
opt.
STANDARD
ENTER
ENTER
OK
ON
Setting Projector Name
(See page 32 for menu setting.)
1.  Display the NETWORK menu. 
2. Press the  or  button to select PROJECTOR 
NAME.
PROJECTOR NAMESET
3. Press the  or  button to select SET .
4.  Press the ENTER button.
•  PROJECTOR NAME screen appears.
PROJECTOR NAME
CODE : XXXXX          V Z $ %
A
OK
capsNEXTSPACECLEAR
DEL
CANCEL
BCDEFGHIJKLMNOPQRSTUVWXYZ0123456789–._!”#$%’()*+,/
←→
5.  Press the direction buttons to move the key cursor, 
select the characters or marks to enter, and press 
the ENTER button.
•  Projector Name can be set using up to 15 
characters including alphabets (capital/small), 
numeric characters, or marks.
 key: ............. Shifting the position of enter 
cursor to the left for each 
character.
 key: ............. Shifting the position of enter 
cursor to the right for each 
character.
DEL key: .......... Deleting the character in the 
position of enter cursor for each 
character.
caps/CAPS key: Switching an alphabet character 
to CAPITAL or small.
NEXT/PREV key: Switching the marks listed on 
the fourth line.
SPACE key: ..... Inserting a space in the position 
of enter cursor.
CLEAR key: ..... Deleting all the entered 
characters.
•  You can enter numbers by pressing the number 
buttons (0 to 9) while holding down the NUM 
button on the remote control. 
6.  When selecting OK, the setting is completed as the 
name stored. However, when selecting CANCEL, 
the setting is completed without storing.•  The display returns the NETWORK menu after 
selecting OK or CANCEL.
•  It may take some time to refl ect the settings.
Network Password Settings
(See page 32 for menu setting.)
1.  Display the NETWORK menu. 
2. Press the  or button to select NETWORK 
PASSWORD.
NETWORK PASSWORDENTER
3.  Press the ENTER button.
• CURRENT NETWORK PASSWORD screen 
appears.
CURRENT NETWORK PASSWORD
A
OK
capsCLEAR
DEL
CANCEL
BCDEFGHIJKLMNOPQRSTUVWXYZ0123456789
←→∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
4.  Press the direction buttons to move the key cursor, 
select the characters or marks to enter, and press 
the ENTER button.
•  Password can be set using up to 32 characters 
including alphabets (capital/small) or numeric 
characters.
 key: ............. Shifting the position of enter 
cursor to the left for each 
character.
 key: ............. Shifting the position of enter 
cursor to the right for each 
character.
DEL key: .......... Deleting the character in the 
position of enter cursor for each 
character.
caps/CAPS key: Switching an alphabet character 
to CAPITAL or small.
CLEAR key: ..... Deleting all the entered 
characters.
•  You can enter numbers by pressing the number 
buttons (0 to 9) while holding down the NUM 
button on the remote control. 
•  The default password is “admin”.
5.  Select OK, and NEW NETWORK PASSWORD 
screen appears if the entered password is correct.
•  If the entered password is not correct, 
CURRENT NETWORK PASSWORD screen 
appears again.
CONFIRM NETWORK PASSWORD
A
OK
capsCLEAR
DEL
CANCEL
BCDEFGHIJKLMNOPQRSTUVWXYZ0123456789
←→↔∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
NEW NETWORK PASSWORD∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗ 
						

							EN-50
6.  Enter the NEW NETWORK PASSWORD and 
CONFIRM NETWORK PASSWORD.
•  Password can be set using up to 32 characters 
including alphabets (capital/small) or numeric 
characters.
 key: ............. Shifting the position of enter 
cursor to the left for each 
character.
 key: ............. Shifting the position of enter 
cursor to the right for each 
character.
 key: ...............  Shifting the position of 
enter cursor between NEW 
NETWORK PASSWORD 
and CONFIRM NETWORK 
PASSWORD.
DEL key: ..........  Deleting the character in the 
position of enter cursor for each 
character.
caps/CAPS key: Switching an alphabet character 
to CAPITAL or small.
CLEAR key: ..... Deleting all the entered 
characters.
•  You can enter numbers by pressing the number 
buttons (0 to 9) while holding down the NUM 
button on the remote control. 
7.  When NEW NETWORK PASSWORD and CONFIRM 
NETWORK PASSWORD are matched, the setting 
is completed after changing the NETWORK 
PASSWORD.
•  When you select OK and the passwords you 
entered are matched, the setting change dialog 
is displayed. After the dialog disappears, the 
NETWORK menu is displayed. 
•  When you select CANCEL, the NETWORK menu 
is displayed without changing the password.
•  If the entered content is not matched, NEW 
NETWORK PASSWORD screen appears again 
after an error dialog is displayed.
•  It may take some time to refl ect the settings.
IP Settings
(See page 32 for menu setting.)
1.  Display the NETWORK menu.
2. Press the  or  button to select IP CONFIG.
IP CONFIGENTER
3.  Press the ENTER button.
•  IP CONFIG menu appears.
IP CONFIG
DHCP
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
0. 0. 0. 0 0. 0. 0. 0
0. 0. 0. 0
MAC ADDRESS
ON
Initial network settings (continued)
Setting or Clearing DHCP
1.  Display the IP CONFIG menu.
2. Press the  or  button to select DHCP.
DHCP
ON
3.  Press the ENTER button.
• Confi rmation dialog appears.
DHCP :
OK : ENTER   CANCEL : MENUON
4. Press the  or  button to select ON  or OFF .
5.  Press the ENTER button.
•  When you select OK, the setting change dialog 
is displayed. After the dialog disappears, the 
NETWORK menu is displayed.
•  To cancel the setting, press the MENU button.
•  It may take some time to refl ect the settings.
•  When setting DHCP to ON, IP ADDRESS, 
SUBNET MASK, and DEFAULT GATEWAY 
cannot be set. If you set those settings, set 
DHCP to OFF and perform the IP settings as the 
following procedures.
IP Address Settings
1.  Display the IP CONFIG menu.
2. Press the  or  button to select IP ADDRESS.
IP ADDRESS
0. 0. 0. 0
3. Press the  or  button to select SET .
4.  Press the ENTER button.
•  IP ADDRESS screen appears.
IP ADDRESS
192 . 168 .    0 .   10
0
OKCLEARDEL
CANCEL
123456789
←→
5.  Press the direction buttons to move the key cursor, 
select the numbers to enter, and press the ENTER 
button.
•  Set the numeric value within the range from 0 to 
255. However, set the numeric value for the fi nal 
octet within the range from 1 to 254.
 key:   Shifting the position of enter cursor to 
the left.
 key:   Shifting the position of enter cursor to 
the right.
 DEL key:  Deleting the character in the position 
of enter cursor for each character.
 CLEAR key:   Deleting all the entered 
characters.
•  You can enter numbers by pressing the number 
buttons (0 to 9) while holding down the NUM 
button on the remote control.