Mitsubishi Xd8100lu Projector User Manual

							EN-31
Menu operation
You can make various settings using the displayed menus.
Following 8 menus are displayed.
IMAGE menu (page 33) INSTALLATION 1 menu (page 34) 
FEATURE menu (page 37) SIGNAL menu (page 39)  INSTALLATION 2 menu (page 35) 
MULTI-SCREEN menu (page 36) 
NETWORK menu (page 40) INFORMATION menu (page 41) 
COMPUTER
0 COLOR
0
TINT
0 SHARPNESS
ADVANCED MENU NCM
SUPER RESOLUTION
IMAGE1 12 2
BRIGHTNESS 0
COLOR ENHANCER
AUTO
CONTRAST
STANDARDCOLOR TEMP.
opt.
0
ENTER
LANGUAGE
ADVANCED MENU
FEATURE
ASPECT
PROJECTOR IDNORMAL
A
AUTO
English
GROUP ID
ALL
DISPLAY INPUT
ENTER
CINEMA MODE
PASSWORD FUNCTION
MENU POSITION
1 12 2opt.
AË
RESET ALLOK
1.
MULTI-SCREEN
EDGE BLENDING
SETTINGOFF
OFF EDGE ADJUST
OFF
COLOR MATCHING
SETTING
MEASURED DATA
MANUAL
MEASURE
1 12 2opt.
REMOTE 1 MODE
FILTER MENU
INSTALLATION 2
AUTO POWER ON
AUTO POWER OFFOFF
ON
BLUE
AUTO
5min
IMAGE CAPTURE
SPLASH SCREEN
DVI LONG CABLE
BACK COLOR
1 12 2opt.
ON
ENTER
ENTER
SETUP
R G BR G B
VHA
U
0
100% COMPUTER INPUT
AUTO
OVER SCAN 
HOLD
USER FINE SYNC.
SIGNAL1 12 2
VERT. POSITION 0 MEMORY CALL
RESOLUTION
(MEMORIZE    )AUTO
HORIZ. POSITION
0 TRACKING
opt.
ENTER
0 1024 x 768
ON
CONTROL SYSTEM
NETWORK PASSWORD
NETWORK1 12 2
NETWORK CERTIFICATION PROJECTOR NAME
IP CONFIG
NETWORK RESET
opt.
STANDARD
ENTER
ENTER
OK
ON
60.00 Hz RESOLUTION
1024 x 768
VERTICAL
FREQUENCY
48.36 kHz
5WIRE HORIZONTAL
FREQUENCY
SYNC. TYPE SERIAL NUMBER
INFORMATION1 12 2
FILTER TIME*****H / ****TIMES
********... NEXT LAMP RELAY
COMPUTER1 INPUT
opt.
*D **H 
RG
HVB
LAMP 1 TIME (LOW)
LAMP 2 TIME (LOW)
COOLING CONDITION
TEST PATTERN
INSTALLATION 1
LAMP MODE
LAMP SELECTSTANDARD
1H/24H
LOW
OFF
STANDARD
0°DUAL
LAMP RELAY
CROSS HATCH
HIGH ALTITUDE MODE
12
STANDBY MODE
IMAGE REVERSE
LENS LOCK
1 12 2opt.
ENTER
****H****H 
						

							EN-32
How to set the menus
1.  Press the MENU button. 
•  The menu selection bar is displayed. 
IMAGE
1 12 2
opt.
Selectable menus are displayed by icons. (The menu 
icon being selected is displayed on a blue background.) 
The name of the menu being 
selected is displayed.
2. Press the  or  button to select a menu to use.
3.  Press the ENTER button (or  button).
•  The selected menu is displayed.
COMPUTER
0 COLOR
0
TINT
0 SHARPNESS
ADVANCED MENU NCM
SUPER RESOLUTION
IMAGE
1 12 2
BRIGHTNESS 0
COLOR ENHANCER
AUTO
CONTRAST
STANDARDCOLOR TEMP.
opt.
0
ENTER
OFF
The item being selected is 
displayed in red letters.
4. Press the  or  button to select an item to adjust. 
SUPER RESOLUTION
IMAGE
1 12 2
BRIGHTNESS 0
COLOR ENHANCER
AUTO
CONTRAST
opt.
0
OFF
5.  Set the selected item by pressing the  or  button. 
IMAGE
1 12 2
BRIGHTNESS 0
COLOR ENHANCER
AUTO
CONTRAST
opt.
2
SUPER RESOLUTIONOFF
6.  To cancel the menu, press the MENU button 
several times. 
Important:
•  When an item marked with “
” is selected, 
pressing the ENTER button makes its value 
effective or displays another screen for further 
setting.
•  When the MENU button doesn’t function, unplug 
the power cord from the wall outlet. Wait about 10 
minutes, plug the power cord in, and try again. 
•  The menus and screens shown in this manual may 
be different from those of the actual projector.
Menu operation (continued) 
						

							EN-33
IMAGE menu
COMPUTER
0 COLOR
0
TINT
0 SHARPNESS
ADVANCED MENU NCM
SUPER RESOLUTION
IMAGE
1 12 2
BRIGHTNESS 0
COLOR ENHANCER
AUTO
CONTRAST
STANDARDCOLOR TEMP.
opt.
IMAGE
ADVANCED MENU
12opt.
NOISE REDUCTION
CTI
INPUT LEVEL
OFFCLOSED CAPTION
OFF
OFF
0
12
0
ENTER
OFF
ITEM SETTING FUNCTION
COLOR ENHANCER AUTO Select to optimize the settings automatically depending on the input signal. 
(Select this option for normal use.)
PRESENTATION Select to make the displayed image look bright and crisp.
STANDARD Select to make the displayed image look natural.
THEATER This option, suitable for viewing movies, makes the displayed image look soft 
and smooth.
sRGB Select to give priority to the color reproducibility.
USER 
Select to set the gamma curve or set BrilliantColor™. (See page 43.)
MULTI-SCREEN 
You can set the gamma curve and BrilliantColor™ in the multi-screen 
application.
SUPER RESOLUTION ON 
 / OFF Use to emphasize the fi neness of the image. (See page 44.)
CONTRAST ±30 Use to adjust the contrast of the projected image. (See page 42.)
BRIGHTNESS ±30 Use to adjust the brightness of the projected image. (See page 42.)
NCM COMPUTER / VIDEO Use to adjust the predetermined tone of each color.
USER 
Use to emphasize only certain colors or to correct the tonal deviation of only 
certain colors. (See page 44.)
OFF NCM doesn’t work. 
COLOR TEMP. STANDARD / LOW / 
HIGHSelect from the predetermined color temperatures. 
USER 
Use to adjust the color temperature to a desired value. (See page 42.) 
COLOR ±10 Use to adjust the color thickness of the projected image. (See page 42.)
TINT ±10 Use to adjust the color tint of the projected image. (See page 42.) 
SHARPNESS ±5 Use to adjust the sharpness of the projected image. (See page 42.)
ADVANCED MENU ENTER 
The ADVANCED MENU is displayed for the following settings.
  NOISE REDUCTION ON / OFF
Use to reduce noise and roughness in the image when noisy video signal is input. 
  CTI ON / OFF Use to correct smeared color boundaries.
  INPUT LEVEL ±5 For analog signal input: 
The input level of video signal differs among devices to be connected. High 
input level causes solid white in displayed image and low input level causes 
displayed image to get dark. Use this menu to adjust the input level of analog 
video signal. 
AUTO /
ENHANCED / 
NORMALFor digital signal input:
 AUTO:   The proper setting is automatically selected. (Selectable only 
when HDMI signal is input.) 
  ENHANCED: Select when solid black occurs.
  NORMAL:  Select when grayish black occurs.
(See page 27.)
  CLOSED CAPTION OFF Does not display captions.
CC1 / CC2 Displays captions.
•  When EDGE BLENDING is ON or COLOR MATCHING is MANUAL or MEASURE in the MULTI-SCREEN menu, you can set only 
MULTI-SCREEN in the COLOR ENHANCER menu. In this case, you cannot set any other items than MULTI-SCREEN. 
•  You can set MULTI-SCREEN in the COLOR ENHANCER menu only when EDGE BLENDING is ON or COLOR MATCHING is 
MANUAL or MEASURE.
•  When COLOR ENHANCER is sRGB, COLOR TEMP., COLOR, TINT and NCM can’t be adjusted.
•  When the setting of COLOR ENHANCER is changed, the displayed image may be disturbed.
•  The effect obtained when SUPER RESOLUTION is ON varies depending on the type and resolution of the input image. 
•  When the COMPUTER1, COMPUTER2, DVI or HDMI is selected as the input source, COLOR and TINT can’t be adjusted.
•  TINT is available only when the NTSC signal is input. 
•  INPUT LEVEL is unavailable when the digital signal is supplied from the YC
BCR/YPBPR terminal of the connected device.
•  Captions are not displayed while information about the menu or input signal selection is being displayed on the screen.
•  The closed caption function displays text information included in the NTSC signal, which is mainly used for TV broadcasting in 
North America.
Menu operation (continued) 
						

							EN-34
INSTALLATION 1 menu
INSTALLATION 1
LENS LOCK
LENS SHIFT LOCK ZOOM/FOCUS LOCK
LENS SHIFT RESETOFF
OFF
COOLING CONDITION
TEST PATTERN
INSTALLATION 1
LAMP MODE
LAMP SELECTSTANDARD
1H/24H
LOW
OFF
STANDARD
0°DUAL
LAMP RELAY
CROSS HATCH
HIGH ALTITUDE MODE
12
STANDBY MODE
IMAGE REVERSE
LENS LOCK
1 12 2opt.1 12 2opt.
ENTER
OK
ITEM SETTING FUNCTION
LAMP MODE STANDARD Select this option when you want to view images in a well-lit room.
LOW Select to moderate the intensity of the lamp. The operating sound is reduced 
and the lamp lifetime becomes longer.
LAMP SELECT DUAL 
LAMP 1 and LAMP 2 illuminate. 
SINGLE 
The lamp with shorter operation time is automatically selected at power-on.
LAMP 1 
LAMP 1 illuminates. (When it is broken or dead, LAMP 2 illuminates automatically.) 
LAMP 2 LAMP 2 illuminates. (When it is broken or dead, LAMP 1 illuminates automatically.)
LAMP RELAY DUAL: OFF The LAMP RELAY doesn’t work. 
1H/24H 
 / 
2H/1W Use to set the lamp relay interval. (See page 53.)
SINGLE:OFF The LAMP RELAY doesn’t work.
24H 
 / 
1 WEEK Use to set the lamp relay interval. (See page 54.)
STANDBY MODE STANDARD Select this option when you control the projector via the LAN, REMOTE 1 IN, 
and SERIAL OUT terminal during power standby. 
LOW Select this option when you don’t control the projector via the LAN, REMOTE 
1 IN, and SERIAL OUT terminal during power standby. This option disables 
the LAN, REMOTE 1 IN, and SERIAL OUT terminal and reduces the power 
consumption during the power standby.
IMAGE REVERSE OFF Select when viewing images from the front with the projector installed on the 
fl oor.
MIRROR Select when viewing images projected from the behind of the screen with the 
projector installed on the fl oor.
INVERT Select when viewing images projected from the behind of the screen with the 
projector installed on the ceiling.
MIRROR INVERT Select when viewing images from the front with the projector installed on the 
ceiling.
HIGH ALTITUDE MODE STANDARD 
Select this option for normal use.
HIGH ALTITUDE 
Select this option for use at an altitude of 2000 to 2700 meters above the sea 
level.
COOLING CONDITION 0° 
 / 45°  / 90°  / 
135°  / 180°  / 
225°  / 270°  / 
315° 
 The cooling condition changes according to the selected projection angle. 
(See page 13.)
TEST PATTERN CROSS HATCH 
Select to show the test cross hatch pattern.
WHITE 
Select to show the maximum brightness image.
BLACK 
Select to show the minimum brightness image.
H. COLOR BARS 
The horizontal color bar pattern is displayed.
V. COLOR BARS 
The vertical color bar pattern is displayed.
LENS LOCK ENTER 
The LENS LOCK menu is displayed for the following settings.
 
ZOOM/FOCUS LOCKON / OFF Use to enable or cancel the FOCUS LOCK and ZOOM LOCK.
  LENS SHIFT LOCK ON / OFF Use to enable or cancel the LENS SHIFT LOCK.
  LENS SHIFT RESET OK 
Use to reset the position of the lens to the factory setting.
•  Regardless of the setting of LAMP MODE, the STANDARD lamp mode is activated by default whenever the projector is turned 
on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about 1 minute after turn-on. 
•  When the lamp mode is switched, the projected image may fl icker. 
•  Frequent switching of the lamp mode may damage the lamp.
•  When using the projector for a long time, set LAMP RELAY.
•  To cancel the test pattern, press any button other than the TEST PATTERN button on the remote control.
•  While the lamps are being switched, an icon 
 is displayed to the right of the INSTALLATION 1 menu bar. While the icon is 
being displayed, you cannot set LAMP SELECT and LAMP RELAY. 
•  After you switch the lamps and the newly selected lamp turns on, you cannot turn off the projector for approx. 1 minute. 
Menu operation (continued) 
						

							EN-35
INSTALLATION 2 menu
REMOTE 1 MODE
FILTER MENU
INSTALLATION 2
AUTO POWER ON
AUTO POWER OFFOFF
ON
BLUE
AUTO
5min
IMAGE CAPTURE
SPLASH SCREEN
DVI LONG CABLE
BACK COLOR
1 12 2opt.
ON
ENTER
ENTER
SETUP
ITEM SETTING FUNCTION
AUTO POWER ON ON / OFF When ON is chosen, the projector is automatically turn on when the power 
cord is plugged in the wall outlet. Choose ON when using the projector 
mounted on the ceiling.
•  The projector is in the stand-by mode when the lamp is off. Use the 
remote control to turn on the lamp. 
AUTO POWER OFF OFF / 5-60min When no video signal is input and no operation is made, the projector 
automatically turns off after the selected time period. A dialog is displayed 5 
minutes before the projector turns off. 
IMAGE CAPTURE SETUP 
Use to capture the screen for the splash screen. (See page 55.)
SPLASH SCREEN  ON / OFF Choose ON to display the splash screen when the power is turned on. 
•  The splash screen can be changed. (See page 55.)
BACK COLOR BLUE / BLACK / 
IMAGEUse to select the background from among BLUE, BLACK and IMAGE, which 
will be displayed when there is no signal input from the source. When IMAGE 
is selected, the splash screen will be displayed.
DVI LONG CABLE AUTO Select this option for normal use.
MANUAL 
Use to adjust the amount of transmission signal correction when a long DVI 
cable is used.  
REMOTE 1 MODE ENTER 
Select when controlling the projector by a control panel connected to the 
REMOTE 1 IN terminal. (See page 61.)
  PIN 1 GND Unchangeable. (Fixed.)
  PIN 2 POWER / NONE  Select POWER or NONE. 
  PIN 3 COMPUTER 1 You can assign COMPUTER 1, COMPUTER 2, VIDEO, S-VIDEO, DVI, HDMI, 
or NONE to each pin.  Though the assignment can be duplicated, the pins 
so assigned become invalid and their settings are displayed with asterisks at 
both ends (like “*COMPUTER 1*”).   PIN 4 COMPUTER 2
 PIN 5 VIDEO
 PIN 6 S-VIDEO
 PIN 7 DVI
  PIN 8 BLANK / NONE  Select BLANK or NONE.
  PIN 9 ON/OFF  Unchangeable. (Fixed.)
 RESET OK 
Settings are reset to the defaults.
FILTER MENU ENTER 
The fi lter menu for the following settings is displayed. 
 CLEANUP PERIOD 24H  
 /  1 WEEK   / 
OFFYou can set the fi lter cleaning interval. (See page 65.)
 MANUAL CLEANUP OK 
Select this option to clean the fi lter immediately. 
•  You can’t set IMAGE CAPTURE and SPLASH SCREEN when PASSWORD FUNCTION in the FEATURE menu has been set to 
SPLASH ID SCREEN to enable the password lock.
•  When you set BACK COLOR to IMAGE and display the splash screen (startup screen) for a long time of period, the after-image 
may remain on the screen. Consult your dealer in this case.
•  Don’t adjust the lens frequently with BACK COLOR set to IMAGE.
•  When STANDBY MODE in the INSTALLATION 1 menu is LOW, you cannot select REMOTE 1 MODE.
Menu operation (continued) 
						

							EN-36
MULTI-SCREEN menu
MULTI-SCREEN
EDGE BLENDING
SETTINGOFF
OFF EDGE ADJUST
COLOR MATCHING
SETTING
MEASURED DATA
MANUAL
MEASURE
1 12 2opt.
ITEM SETTING FUNCTION
EDGE BLENDING OFF Select when using the projector alone.
ON Select when using the projector to confi gure the multi-screen consisting 
of multiple projectors. 
The following settings in the SETTING become enabled to make the 
overlapped area of the displayed images unnoticeable.
SETTING EDGE ADJUST 
Use to make the overlapped area of the screens unnoticeable in the 
multi-screen application. Use this setting to select the edges to be 
overlapped or to set the overlapped areas. (See page 47.)
BLACK LEVEL 
In the multi-screen application, the black level in the areas where images 
are overlapped will become bright. So, use this setting to adjust the 
black level in non-overlapped areas. (See page 47.)
BRIGHT UNIFORMITY 
CORRECTION 
Use to correct non-uniformity in the screen brightness of the single 
projector to facilitate edge blending. (See page 47.)
RESET 
Use to reset the values of EDGE ADJUST , BLACK LEVEL  and 
BRIGHT UNIFORMITY CORRECTION  to the defaults. 
COLOR MATCHING OFF Select this option when the projector is used alone. 
MANUAL Select this option when adjusting colors while viewing the screen to 
correct color variations among the projectors.
MEASURE Select this option when adjusting colors using a measuring instrument 
to correct color variations among the projectors.
MANUAL SETTING 
The test signal is displayed. Make adjustment so that the color tones of 
each image match among the adjoining projectors. (See page 48.) 
RESET 
Use to reset the value of SETTING  in the MANUAL to the default.
MEASURE MEASURED DATA 
The test signal is displayed. Measure the brightness and chromaticity of 
each image using a measuring instrument (chroma meter) and enter the 
measurement values. (See page 48.) 
TARGET DATA 
Use to set the target chromaticity value of each color. (See page 48.)
RESET 
Use to reset the values of MEASURED DATA  and TARGET DATA  in 
the MEASURE to the defaults.
•  When EDGE BLENDING is ON or COLOR MATCHING is MANUAL or MEASURE, you can set only MULTI-SCREEN in the 
COLOR ENHANCER menu. In this case, you cannot set any other items than MULTI-SCREEN. 
•  The edge blending function can be used with non-directional screens. If you use a directional screen, the areas where images 
are overlapped seem discontinuous depending on the viewing angle. 
•  The target chromaticity value entered for TARGET DATA in the MEASURE menu is just for guidance. If the obtained result 
doesn’t match with the colors displayed on the adjoining projectors, adjust the value while viewing the screens. 
Menu operation (continued) 
						

							EN-37
FEATURE menu
LANGUAGE
ADVANCED MENU
FEATURE
ASPECT
PROJECTOR IDNORMAL
A
AUTO
English
GROUP ID
ALL
DISPLAY INPUT
ENTER
CINEMA MODE
PASSWORD FUNCTION
MENU POSITION
1 12 2opt.
RESET ALLOK
FEATURE
ADVANCED MENU
SETUP
SCART INPUTAUTO
AUTO
OFF
STANDARD
OFF
2 2
VIDEO SIGNAL
LAMP WARNING
HIDE OSD
LAMP 1 TIME RESET
OK
LAMP 2 TIME RESET
OK
FILTER TIME RESET
OK
1 1opt.
1.
ITEM SETTING FUNCTION
ASPECT NORMAL Select to change the aspect ratio automatically depending on the 
input signal. (Select this option for normal use.) 
16:9 
Select to expand squeezed (or horizontally compressed) images 
such as DVD images to 16:9. Press the ENTER button to make 
further settings such as positioning of the displayed image and 
selection of signals expanded by this function.  (See page 30.)
FULL Select to project images in full size (1024 x 768 pixels) irrespective 
of type of input signal.
PROJECTOR ID ALL Select this option to control the projector regardless of the ID 
number. (See page 60.)
01 to 63 Use to set the ID number (two-digit number). (See page 60.)
GROUP ID A to Z Use to set the ID number for controlling multiple projectors by 
groups for monitoring and control via the SERIAL terminal. (See 
page 60.)
PASSWORD FUNCTION DISPLAY INPUT 
 /
MENU ACCESS  /
 
SPLASH ID SCREEN 
Use to enable or cancel the password lock. See page 56 for details. 
MENU POSITION 1 (upper left) / 2 (lower right) / 
3 (center)Use to change the position of the menu. 
CINEMA MODE AUTO The fi lm mode will be automatically activated when a fi lm source 
signal is input.
Select AUTO for normal use.
When fl icker occurs on the screen, frame dropping or other incorrect 
display occurs, or jaggies on slanting lines are remarkable, select 
either FILM or VIDEO, which improves the symptom better.
FILM Fixed to the fi lm mode.
VIDEO The fi lm mode will not be activated.
LANGUAGE
 / English / Español / 
Deutsch / Français / Italiano / 
 /  /  / 
PORTUGUÊS / SVENSKA / 
POLSKI / Nederlands/ 
Norsk(Bokmål) / Türkçe / 
 / Bahasa Indonesia / 
Bahasa Melayu / 
Use to select the language used in the menus. 
ADVANCED MENU ENTER 
The ADVANCED MENU is displayed for the following settings.
  VIDEO SIGNAL AUTO / NTSC / PAL / SECAM 
/ 4.43NTSC / PAL-M / PAL-N / 
PAL-60When AUTO is selected, the appropriate video format is 
automatically selected depending on the input signal. If the image 
isn’t displayed correctly, select the desired video format manually.
  SETUP AUTO Select to change the SETUP mode automatically.
OFF Select to make black lighter. 
3.75% / 7.5% Select to make black thicker. 
•  When 7.5% is chosen, the brightness is decreased by the set-
up cancel function for the U.S. Choose OFF when the image is 
dark.
  SCART INPUT ON / OFF Choose ON when connecting the projector with a device equipped 
with the SCART terminal that can output RGB signal. SCART 
terminal is used mainly in Europe. Choose OFF normally. (Available 
only for the input signal from the COMPUTER/COMPONENT VIDEO 
IN-1 terminal.)
Menu operation (continued) 
						

							EN-38
ITEM SETTING FUNCTION
 LAMP WARNING
STANDARDWhen the lamp operating time exceeds 3000 hours with LAMP 
MODE set to LOW, a warning dialog is displayed.
SHORT TERMWhen the lamp operating time exceeds 3800 hours with LAMP 
MODE set to LOW, a warning dialog is displayed.
 HIDE OSD
OFFSelect this option for normal use.
ON  The no-signal dialog, input dialog, SCART warning dialog, auto 
power-off dialog, lamp warning dialog, and abnormal temperature 
dialog aren’t displayed.
  LAMP 1 TIME RESET OK 
The LAMP 1 operation time is reset to 0. 
  LAMP 2 TIME RESET OK 
The LAMP 2 operation time is reset to 0. 
  FILTER TIME RESET OK 
The fi lter operation time and the cleaning count is reset to 0. 
RESET ALL OK 
The menu settings are reset to the factory defaults (except the 
LANGUAGE, PASSWORD FUNCTION, IMAGE CAPTURE, and 
NETWORK settings).
•  CINEMA MODE can be adjusted only when a TV60, TV50, 480i, 576i or 1080i signal is being displayed.
•  When SCART INPUT is set to ON, normal computer signals aren’t projected. 
•  Use a commercially available SCART-Mini D-SUB 15-pin cable when connecting this projector with an AV device equipped 
with the SCART terminal.
•  Some AV devices equipped with the SCART terminal aren’t compatible with this projector.
•  The RESET ALL process may take some time to complete. 
•  You cannot carry out RESET ALL for approx. 2 minutes after the lamp switching or the lamp relay operation. 
FEATURE menu (continued)
Menu operation (continued) 
						

							EN-39
SIGNAL menu
R G BR G B
VHA
U
0
100% COMPUTER INPUT
AUTO
OVER SCAN 
HOLD
USER FINE SYNC.
SIGNAL1 12 2
VERT. POSITION 0 MEMORY CALL
RESOLUTION
(MEMORIZE    )AUTO
HORIZ. POSITION
0 TRACKING
opt.1 12 2opt.
SIGNAL
RESOLUTION (MEMORIZE)
VERTICAL 
FREQUENCY
HORIZONTAL 
FREQUENCY
HORIZ. PIXELS
VERT. LINES 
EXECUTE
CANCEL 60.00 Hz
1
48.36 KHz
1024
768
ENTER
0 1024 x 768
OFF
0
SHUTTER(L)0
SHUTTER(LS)
0SHUTTER(RS)
LPF
SIGNAL
USER1 12 2
VERT. SYNC. AUTO
CLAMP WIDTH
0SHUTTER(U)
opt.
1
OK
OK
?
CLAMP POSITION
ON
ITEM SETTING FUNCTION
MEMORY CALL AUTO / 
MEMORY 1 
 / 
MEMORY 2 Use to select the setting of RESOLUTION (MEMORIZE) already saved. 
Impossible to select if no setting has been saved. AUTO is selected by 
default. It optimizes the signal format automatically depending on the type of 
video signal supplied from the computer. Press the ENTER button to clear the 
setting already saved. 
RESOLUTION (MEMORIZE  )The current resolution is displayed. To change the current setting, press the 
ENTER button to display the RESOLUTION (MEMORIZE) menu. The new 
setting can be saved to MEMORY 1 or MEMORY 2.
 
VERTICAL FREQUENCY- The vertical frequency of the currently projected video signal is displayed.
 HORIZONTAL FREQUENCY- The horizontal frequency of the currently projected video signal is displayed.
  HORIZ. PIXELS 640-1920 The number of horizontal pixels of the currently projected video signal is 
displayed. When you change the current setting, select EXECUTE, and then 
press the ENTER button, the image is automatically adjusted according to 
the resolution you set. The adjustment result can be saved to MEMORY 1 or 
MEMORY 2.
  VERT. LINES 350-1200 The number of vertical lines of the currently projected video signal is 
displayed. When you change the current setting, select EXECUTE, and then 
press the ENTER button, the image is automatically adjusted according to 
the resolution you set. The adjustment result can be saved to MEMORY 1 or 
MEMORY 2.
 EXECUTE OK 
Press the ENTER button to start the automatic adjustment. At the completion 
of the automatic adjustment, a message is displayed and you can save the 
adjustment result to MEMORY 1 or MEMORY 2.
 CANCEL OK 
The process to change the current resolution is canceled and the SIGNAL 
menu is displayed.
HORIZ. POSITION 0-999 Use to adjust the horizontal position of the projected image. 
VERT. POSITION 0-999 Use to adjust the vertical position of the projected image. 
FINE SYNC. 0-31 Use to eliminate fl ickering or blur, if appears, viewing the projected image. 
TRACKING 0-9999
Use to eliminate vertical wide stripes, if appears, viewing the projected image.
COMPUTER INPUT AUTO The proper setting is automatically selected.
RGB Select this option when connecting the projector to high defi nition video 
equipment having R, G, and B output terminals.
YC
BCR/YPBPRSelect this option when connecting the projector to a DVD player or other device 
having Y, CB, and CR (or Y, PB, and PR) component video output terminals. 
OVER SCAN 100%-90% Use to adjust the display area of projected image.
HOLD OFF / ON 
Use to adjust the image when fl agging occurs near the top of the screen.
USER ENTER The USER menu is displayed for the following adjustments.
  CLAMP POSITION 1-255 Use to correct solid white or solid black in the projected image. 
  CLAMP WIDTH 1-63 Use to correct solid black in the projected image. 
  VERT. SYNC. AUTO / OFF Use to adjust the image when its motion doesn’t run smoothly. Select AUTO 
for normal use.
  LPF ON / OFF Use to select whether or not to enable the LPF. (See page 46.)
  SHUTTER(U) 0-38 Use to adjust the image when noise appears on the top part of the image.
  SHUTTER(L) 0-38 Use to adjust the image when noise appears on the bottom part of the image.
  SHUTTER(LS) 0-63 Use to adjust the image when noise appears on the left half of the image.
  SHUTTER(RS) 0-63 Use to adjust the image when noise appears on the right half of the image.
•  Though horizontal strips may appear on the enlarged projected image, such symptom is not a malfunction.
•  When you change the horizontal or vertical position to a large extent, noise may appear. 
•  The adjustable range of the vertical position varies depending on the type of the input signal. Though the image may stay in the same 
position even when the setting value is changed, such symptom is not a malfunction.
•  SHUTTER will not work correctly during keystone adjustment. 
•  When you increase the setting value of OVER SCAN, noise may appear on the screen.
•  See pages 45 and 46 for the detailed setting procedure.
Important:
•  You can set the IMAGE menu and the SIGNAL menu only when the signal is supplied. 
Menu operation (continued) 
						

							EN-40
NETWORK menu
CONTROL SYSTEM
NETWORK PASSWORD
NETWORK1 12 2
NETWORK CERTIFICATION PROJECTOR NAME
IP CONFIG
NETWORK RESET
opt.
STANDARD
NETWORK
IP CONFIG
12opt.
DHCP
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
0. 0. 0. 0 0. 0. 0. 0
0. 0. 0. 0
MAC ADDRESS
12
ENTER
ENTER
OK
ON
ON
ITEM SETTING FUNCTION
PROJECTOR NAME *****... Displays PROJECTOR NAME. Displays PROJECTOR NAME in blank 
when PROJECTOR NAME is not set. (See page 49.)
SET 
Set the name to identify the projector. Enter up to 15 characters 
(alphabets or numeric characters). (See page 49.)
NETWORK PASSWORD ENTER 
Set the password for Web control or PJLink certifi cation. (See page 
49.)
IP CONFIG ENTER 
Select this setting for IP Confi guration. (See page 50.)
 DHCP
ON 
 / OFF  Use this setting when you obtain IP CONFIG automatically by DHCP 
server.
  IP ADDRESS ***.***.***.*** Displays IP ADDRESS. However, IP ADDRESS is not set as factory 
default, and cannot be displayed.
SET 
Set IP ADDRESS. When DHCP is set to ON, you cannot change
this setting.
  SUBNET MASK ***.***.***.*** Displays SUBNET MASK. However, SUBNET MASK is not set as 
factory default, and cannot be displayed.
SET 
Set SUBNET MASK. When DHCP is set to ON, you cannot change 
this setting.
  DEFAULT GATEWAY ***.***.***.*** Displays DEFAULT GATEWAY. However, DEFAULT GATEWAY is not 
set as factory default, and cannot be displayed.
SET 
Set DEFAULT GATEWAY. When DHCP is set to ON, you cannot 
change this setting.
  MAC ADDRESS xx-xx-xx-xx-xx-xx Displays MAC ADDRESS.
NETWORK CERTIFICATION
ON 
 / OFF  Select whether to enable the network certifi cation or not. Select ON 
for normal use. (See page 51.)
CONTROL SYSTEM STANDARD 
Select this setting when using ProjectorView Global+ or ProjectorView. 
(See pages 51 and 58.)
AMX 
Select when using a controller made by AMX. (See pages 51 and 58.)
CRESTRON 
Select this setting when using the controller or software of Crestron 
Electronics, Inc. (See pages 51 and 58.)
NETWORK RESET OK 
Resets the Network Setting. (See page 52.)
Menu operation (continued)