Mitsubishi Xd8100lu Projector User Manual

EN-51
6.  When selecting OK, the setting is completed as 
the IP ADDRESS stored. However, when selecting 
CANCEL, the setting is completed without storing.
•  When the setting you entered is correct, the 
setting change dialog is displayed. After the 
dialog disappears, the NETWORK menu is 
displayed. If the entered content is not correct, 
IP ADDRESS screen appears again after an 
error dialog is displayed.
•  It may take some time to refl ect the settings.
Subnet Mask Settings
1.  Display the IP CONFIG...

EN-52
Initialization of Network Settings
(See page 32 for menu setting.)
1.  Display the NETWORK menu. 
2. Press the  or  button to select NETWORK 
RESET.
NETWORK RESET
OK
3.  Press the ENTER button.
• Confi rmation dialog appears.
4.  If pressing the ENTER button again, the Network 
Settings can be initialized.
•  It may take some time to refl ect the settings.
How to Use Network Function 
•  When connecting a computer and projector with 
LAN, confi gure the both IP Addresses in the 
same network group....

EN-53
Lamp relay
Using the lamp relay function, you can project images 
continuously. The lamp relay function automatically 
rests or switches the lamps. The lamp relay is 
performed when LAMP SELECT in the INSTALLATION 
1 menu is set to DUAL or SINGLE. 
Setting the lamp relay interval
When LAMP SELECT is set to DUAL:
Either of the lamps is automatically put to rest.
(See page 32 for menu setting.)  
1.  Display the INSTALLATION 1 menu.
2. 
Select LAMP SELECT by pressing the  or  button.
12LAMP SELECT...

EN-54
•  Immediately after the power-on, during the lamp 
selection, or during the lamp relay operation, you 
cannot change the setting of LAMP SELECT and 
LAMP RELAY. 
•  In the case of continuous projection, the lamps may 
deteriorate earlier unless they are turned off for 1 
hour per week. 
•  When using this projector continuously for a long 
time of period, enable LAMP RELAY.
•  The brightness and color tint vary at the time of 
lamp switching.
When LAMP SELECT is set to SINGLE:
The lamps are...

EN-55
•  The image within the outer edges of the red 
frame is captured. 
•  The captured image is displayed in the REAL 
mode automatically.
CAPTURE : ENTER + ENTER
CANCEL : MENUCAPTURE : ENTER X2
CANCEL : MENU
12.Adjust the size of the image to be captured so that 
such image stays within the red frame. 
• Press the , ,  or  button to move the red 
frame.
• You can’t move the red frame outside the 
scr
een. 
• Press the MENU button to cancel the 
procedure.
CAPTURE : ENTER X2
CANCEL : MENU
13....

EN-56
Password function
This projector is equipped with the password function 
that is designed for prevention of wrong operation by 
children and restriction on operation by other than 
specifi ed users. The password function has 3 modes 
as follows.
DISPLAY INPUT .......... When the projector is turned 
on, the startup screen (or splash screen) will appear 
and stay on the screen until the password is 
entered. When the password is entered, the startup 
screen will switch to the regular operation...

EN-57
Picture in Picture (PinP) 
One of the special features of this projector is the 
picture-in-picture (PinP) mode. The PinP mode allows 
you to view the images from different sources at the 
same time. 
•  While viewing the image from the COMPUTER1, 
COMPUTER2, DVI, or HDMI input source, you can 
display the image from the VIDEO or S-VIDEO input 
source as a sub image.
Sub image
To use the PinP mode
1.  Press the PinP button on the remote control. 
2.  If necessary, select the desired external input...

EN-58
Important:
•  When you set CONTROL SYSTEM to CRESTRON 
in the NETWORK menu, the web control for 
Crestron is enabled. For such control, Adobe Flash 
Player should be installed in advance. You can 
download Adobe Flash Player from the website of 
Adobe Systems Incorporated.
•  When you set CONTROL SYSTEM to CRESTRON 
in the NETWORK menu, you cannot use the control 
by ProjectorView Global+, which is the software 
supplied with the projector. 
About PJLink™
•  To use PJLink™ function, the PJLink™...

EN-59
Connection
For details of the connection, see “LAN control UTILITY operation manual” in the CD-ROM.
When STANDBY MODE of the INSTALLATION 1 menu of the projector is set to LOW, the LAN network is disabled. 
To enable the LAN network, set STANDBY MODE to STANDARD. (See page 34 .)
Confi gure the initial network settings fi rst. 
You can confi gure the initial settings using the projector menu (see pages 49 to 52) or ProjectorView Global+. For 
details of ProjectorView Global+, see “LAN control UTILITY...

EN-60
Monitoring and control using SERIAL terminal
Using the SERIAL terminal, you can monitor and control multiple projectors collectively or individually. 
•  For details, contact your dealer. 
To RS-232C terminal
To SERIAL 
INTo SERIAL 
INTo SERIAL 
IN To SERIAL 
OUTTo SERIAL 
OUT RS-232C cable RS-232C cable
•  See also the instruction manuals of the devices to 
be connected. 
Connection
•  Make sure that the power supplies of the projector 
and the computer are off. 
1.  Connect one end of an RS-232C...