Mitsubishi Xd3200u Dlp Projector User Manual

EN-41
Supervising and controlling by computer
You can supervise and control the projector’s operation using a personal computer via a LAN network. 
•	 To	supervise	and	control	the	projector,	install	the	software	“Projector-Control	Device	Installer	*”	contained	in	the	
attached CD-ROM. For the installation procedure and usage of the software, see “User Manual for LAN Control 
Utility” contained in the attached CD-ROM. 
 *) Functions•	 Setting	of	the	projector’s	IP	address•	 Setting	of	password,	display...

EN-42
Indicators
This projector has 2 indicators, each of which shows the operation condition of\
 the projector. 
The following offer solutions to possible problems. If these problems persist, turn the projector off and consult your 
dealer. 
POWER indicator STATUS indicator
Normal condition
POWERSTATUSCONDITIONNOTE
Steadyred
OffStand-by
Blinkinggreen
Lamp stand-by for power-offThe power cannot be turned on by pressing the POWER button.
Steadygreen
Blinkinggreen
Lamp stand-by for power-onThe power...

EN-43
Replacing the lamp
This projector is equipped with a lamp to project images. This lamp is a consumable. It may burn out or its brightness 
may decrease during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to replace the 
lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp. 
Spare lamp VLT-XD3200LP
Warning:
•	 Be	careful	not	to	drop	the	lamp	fixing	screws	into	the	inside	of	the	projector.	Don’t	put...

EN-44
Replacing the lamp (continued)
To replace the lamp:
1. Turn off the main power switch and unplug the 
power cord. 
2. Loosen the screw (a) using a Phillips screwdriver 
(+),	and	remove	the	lamp	cover	(b).
(a) (b)
3. 
Loosen the screws (c) using a Phillips screwdriver 
(+).
(c)
4. Pull the handle.
5. Pull out the lamp box by the handle while holding 
the projector.
•	Pull the lamp box out of the projector slowly. 
If it is pulled out quickly, the lamp may break 
scattering glass fragments.
•	Do not...

EN-45
When removing the lamp from the ceiling-mounted projector
When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the 
projector or option lamp to prevent glass fragments from scattering.
•	 Assemble	the	lamp	replacement	tray	according	to	the	procedure	shown	on	it.
1. Follow steps 1 to 4 on page 44.
2. Attach the lamp replacement tray to the projector as shown in the 
figure.
3. Secure the lamp replacement tray on the projector using the tape 
packed...

EN-46
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be 
sure to unplug the power plug, and then contact your dealer. 
No image appears on the screen. 
ProblemSolution
Power can not be 
turned on.
•	 Check	whether	the	indicators	are	on	or	off	and	how	they	are	lightning.
POWERSTATUSSolution
OffOff
•	 Connect	the	power	cord	to	the	projector.
•	 Plug	the	power	cord	into	a	wall	outlet.
•	 Turn	on	the	main	power	swich.
•...

EN-47
Troubleshooting (continued)
No image appears on the screen. (continued) 
ProblemSolution
“NO SIGNAL” is 
displayed.
•	 Turn	on	the	power	of	the	connected	device,	or	check	whether	there	is	something	
wrong with the connected device.
•	 Check	whether	the	external	device	output	signals.	(Check	this	especially	when	the	
external device is a notebook computer.) 
•	 Check	that	the	cable	connected	to	the	external	device	isn’t	defective.	
•	 Check	that 	the 	projector 	is 	connected 	to 	the 	external...

EN-48
Troubleshooting (continued)
Images are not displayed correctly. (continued) 
ProblemSolution
Different color tint.•	 When	comparing	images	projected	by	two	projectors,	tints	in	the	displayed	images	
may be different because of variation between their optical components. This is not a\
 
malfunction. 
•	 When	comparing	the	image	projected	by	this	projector	with	those	displayed	on	the	
television or PC monitor, tints in the displayed images may be different because of 
difference in the range of...

EN-49
Troubleshooting (continued)
If the following problem occurs after the lamp is replaced, check the following first. 
ProblemSolution
The projector does not 
turn on. 
•	 Fit	the	lamp	cover	securely.	(See	pages	43	and	44.)		
•	 Reset	the	lamp	operating	time.	(See	page	44.)
The STATUS indicator 
blinks.
•	 Reset	the	lamp	operating	time.	(See	page	44.)
Kensington Lock
This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. 
Refer to the...

EN-50
Specifications
The specifications and outside appearance of the projector are subject to change without prior notice.
TypeDLP™ projector
ModelXD3200U
Display technology0.7-inch Single chip DMD
Pixel 1024 x 768 = 786432 pixels
Projection lensF 2.0 - 2.4  f= 24.5 - 33.1 mm
Light-source lamp330 W
Image size (projection distance)40” min. to 300” max. (projection distance 1.4 to 10.6 m)
Maximum resolutionComputer signalMaximum resolution:  1600 x 1200 dots (compressed)
Panel resolution: 1024 x 768 dots...