Mitsubishi Xd3200u Dlp Projector User Manual

EN-11
Setting up your projector (continued)
Adjusting the position of the projected image
To adjust the positions of the projector and the screen, use LENS SHIFT button.
1. Press the LENS SHIFT button.
•	The LENS SHIFT menu appears at the center of the screen.
2. Press the , ,  or  button to move the image position.
•	When the  button is pressed, the image moves down.
•	When the  button is pressed, the image moves up.
•	When the  button is pressed, the image moves to the right.
•	When the  button...

EN-12
Setting up your projector (continued)
Front projection, ceiling mounting
For ceiling mounting, you need the ceiling mount 
kit designed for this projector. Ask a specialist for 
installation. For details, consult your dealer.
•	 The	warranty	on	this	projector	does	not	cover	any	
damage caused by use of any non-recommended 
ceiling mount kit or installation of the ceiling mount 
kit in an improper location. 
•	 When	using	the	projector	mounted	on	the	ceiling,	
set IMAGE REVERSE in the INSTALLATION...

EN-13
2
1
Viewing computer images
2
1
AUDIO OUTAUDIO IN-1/2
2
1
A. Connecting the projector to a computer
Preparation: 
•	 Make	sure	that	the	power	of	the	projector	and	that	of	the	computer	are	turned	off.	
•	 When
	connecting 	the 	projector 	to 	a 	desktop 	computer, 	disconnect 	the 	RGB 	cable 	that 	is 	connected 	to 	the 	monitor.	
For analog connection: 
(For using the COMPUTER/COMPONENT VIDEO IN-1 
terminal.)
1.  Connect one end of the supplied RGB cable to the 
COMPUTER/COMPONENT VIDEO IN-1...

EN-14
Viewing computer images (continued)
1. Plug the attached power cord into the power cord inlet of 
this projector.
2. Plug the other end of the power cord into a power outlet.
•	 The	power	cords	for	use	in	the	U.S.	and	Europe	are	included	with	this	projector.	Use	the	appropriate	one	for	your	
country. 
•	 This	projector	uses	the	power	plug	of	3-pin	grounding	type.	Do	not	take	away	the	grounding	pin	from	the	power	
plug. If the power plug doesn’t fit your wall outlet, ask an electrician to change the...

EN-15
C. Installing the terminal cover
This projector includes a terminal cover. If necessary, install the terminal cover to the projector.
1. Fit two hooks of the terminal cover into the projector.
2. Tighten the attachment screws (a) firmly.
Important:
•	Don’t carry the projector by the terminal cover. 
(a)
Viewing computer images (continued) 

EN-16
Viewing computer images (continued)
D. Projecting images
Preparation:
•	 Remove	the	lens	cap.
POWER buttonCOMPUTER/DVI-D button COMPUTER 1, 2 buttons
LENS SHIFT buttonPOWER button
ZOOM/FOCUS button LENS SHIFT button
Main power switch
ZOOM/FOCUS buttonDVI-D(HDCP) 
button
POWER indicator
STATUS indicator
ENTER button
, , ,  buttons ENTER button
, , ,  
buttons
1. 
Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 
•	 If	the	projector	was...

EN-17
Viewing computer images (continued)
9. Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.
10. Adjust with the  or  button to get an approximate size. 
•	 When	the	ENTER	button	is	pressed	while	the	ZOOM/FOCUS	menu	is	displayed,	the	adjustment	mode	is	
switched between FAST and STEP. When FAST is selected, the speed of zoom controlled by the  or  
button becomes fast, and it becomes slow when STEP is selected.
11. Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of...

EN-18
AV mute
The video and audio signals are temporarily muted when the AV MUTE button is pressed. To cancel muting, press the 
AV MUTE button again.
•	 It	takes	several	seconds	before	muting	is	completely	canceled.	
•	 If	AV	MUTE	MODE	in	the	INSTALLATION	menu	is	set	to	IMAGE,	the	splash	screen	will	appear	when	the	AV	MUTE	
button is pressed. 
•	 You	can	alter	the	splash	screen	optionally.	See	page	37.	
•	 The	audio	from	the	AUDIO	OUT	terminal	is	also	muted	by	pressing	the	AV	MUTE	button.
AUTO POSITION...

EN-19
Viewing video images
Connecting to a video player, etc.
1. Connect one end of a commercially available video cable 
to the VIDEO IN terminal of the projector.
2. Connect the other end of the video cable to the video 
output terminal of the video equipment.
3. Connect one end of a commercially available audio cable 
to the audio input terminals (L/MONO, R) of the projector.
4. Connect the other end of the audio cable to the audio 
output terminals (L, R) of the video equipment.
When the video...

EN-20
Viewing video images (continued)
Projector + DVD player or HDTV decoder
Some DVD players have an output connector for 3-line fitting (Y, CB, CR). When connecting such DVD player with this 
projector, use the COMPUTER/COMPONENT VIDEO IN-2 terminals. 
CB(PB)
Y  CR(PR) 
B 
G  R 
AUDIO IN-2
BNC cable (option)
DVD player or HDTV decoder BNC-RCA connector (option)
COMPUTER/COMPONENT 
VIDEO IN-2
Audio cable (option)
To audio output terminals
•	 The	terminal’s	names	Y,	PB, and PR are given as examples of...