Mitsubishi Xd250u-St Data Projector Users Manual

EN-11
ENGLISH
Basic connections (continued)
Connection (for video equipment having an HDMI terminal)
Important: Use a commercially available HDMI (with HDMI logo) cable.
 You don’t have to connect any cable for audio input. You can input video and audio using an HDMI cable only.
 When HDMI audio isn’t output, it may be output by turning off the power of the video equipment with the projector and the video equipment con-
nected to each other and then turning back on the power.
 Some cables may not be...

EN-12
Basic connections (continued)
Projector + Computer 
For computer with Mini D-SUB  
For analog connection: 
1. Connect one end of the supplied RGB cable to the COMPUTER IN terminal (1, 2) of the projector.
2. Connect the other end of the RGB cable to the monitor port of the computer. 
For monitor connection:Connect the RGB cable from the monitor to the MONITOR OUT terminal of the projector.
 Images may not be displayed correctly depending on the type of the input signal. See the instruction manual...

EN-13
ENGLISH
Preparation
Preparation for projection 1. Attach the provided power cord to the projector. 
2. Plug the power cord in the wall outlet. 
3. Remove the lens cap.
Warning:  Do not look into the lens directly when the projector is on.
 The lens cap is for protecting the lens. If you leave the lens cap on 
the lens with the projector turned on, it may be deformed because 
of heat build-up. Remove the lens cap when you turn on the pro-
jector. 
 One of power cords for the U.S., Europe and U.K. is...

EN-14
Basic operation
Power-on 1. Turn on the device connected to the projector first. 
2. Plug the power cord in the wall outlet. 
 The POWER indicator lights up. 
 If the power cord is unplugged from the wall outlet before the 
projector is cooled down completely after use, the fans may 
start rotating when the power cord is plugged in next time 
and the POWER button may not function. In this case, wait 
for the fans to stop and press the POWER button to light the 
indicator. 
3. Press the POWER button...

EN-15
ENGLISH
Basic operation (continued)
Power-off Use the following procedure to turn off the projector.
The lamp may deteriorate if the projector is powered off and on 
repeatedly within 30 minutes after the lamp is lighted.
1.Press the POWER button on the control panel or the STANDBY 
button on the remote control. 
 The message POWER OFF? YES : PRESS AGAIN 
appears on the screen.
 To cancel, press any button except the POWER button. 
(Some buttons on the remote control don’t function for can-
cel.)...

EN-16
Basic operation (continued)
Wall ScreenThis function is to reproduce natural color tones when images are pro-
jected directly onto a screen or wall surface. You can select from 
BEIGE, LIGHT BLUE, LIGHT GREEN, PINK, BLACK BOARD, WHITE 
BOARD, and OFF, to match the color of the screen or wall to be used 
for projection.
1. Display the INSTALLATION menu. (See page 21 for more details.)
2. Press the S or T button to select WALL SCREEN.
3. Press the W or X button to select the color closest to that of...

EN-17
ENGLISH
Menu operation
As one of the two types of MENU display, following QUICK MENU appears on the screen when pressing MENU button on the remote control. In 
addition, DETAIL MENU (See page 19) appears when selecting DETAIL MENU in this MENU and pressing ENTER button.
 Comparing QUICK MENU with DETAIL MENU, if the contents in those two menus are same each other, the functions in those two menus are 
same as well.
 To close QUICK MENU or DETAIL MENU, press MENU button when MENU is displayed.
QUICK...

EN-18
Menu operation (continued)
Menu OptionsSet the following options provided in the respective menus.
1. QUICK MENU
 You cannot adjust COLOR TEMP. when WALL SCREEN is set to other than OFF.
 When COLOR ENHANCER is switched, projected images may be distorted.
 By default, the LAMP MODE is set to STANDARD. The LAMP MODE is set to either STANDARD or LOW depending on the setting last selected, 
and you cannot switch the LAMP MODE in about one minute after the lamp is on.
2. INFORMATION menu
Menu option...

EN-19
ENGLISH
Menu operation (continued)
DETAIL MENU* Menus are not displayed when no signal is supplied to the projector.
IMAGE
INSTALLATION
FEATURE
SIGNAL
INFORMATIONCOLOR ENHANCER
CONTRASTBRIGHTNESS
COLOR TEMP.
AUTOPRESENTATIONSTANDARD
±30±30STANDARD
COLOR *1
TINT *1
SHARPNESS *1
ADVANCED MENU
±10±10±5
WALL SCREEN
LAMP MODE
STANDBY MODE
AUDIO INPUT
AUTO KEYSTONE
IMAGE REVERSE
ADVANCED MENU
STANDARD, LOWSTANDARD, LOWAUTO, AUDIO 1, AUDIO 2, AUDIO 3, MIX       *6
BLACK BOARDWHITE BOARDOFF
OFF, MIRROR,...

EN-20
Menu operation (continued)
Basic operationSeveral settings can be adjusted using the menu.
Example : Auto power off time setting
1. Press the MENU button.
2. Select the DETAIL MENU and press the ENTER button  (or T 
button).
3. Press the W or X button to select INSTALLATION. 
4. Press the ENTER button (or T button).5. Press the S or T button to select AUTO POWER OFF.
6. Press the W or X button to adjust the auto power off time.
7. Exit the menu by pressing the MENU button several times.
Important:...