Mitsubishi Tx20u Projector User Manual

Menu operation (continued)
EN-31
SIGNAL menu (continued)
 Though horizontal strips may appear on the enlarged projected image, such symptom is not a malfunction. 
 When you change the horizontal or vertical position to a large extent, noise may appear. 
 The adjustable range of the vertical position varies depending on the type of the input signal. Though the image may stay in the
same position even when the setting value is changed, such symptom is not a malfunction.
 SHUTTER will not work correctly...

EN-32
Menu operation (continued)
NETWORK menu
ITEM SETTING FUNCTION
PROJECTOR NAME
*****... 
 Set the name to identify the projector. Enter up to 15 characters (alphabets 
or numeric characters). (See page 40.)
NETWORK 
CERTIFICATIONON
  / OFF  Select whether to enable the network certification or not. Select ON for 
normal use. (See page 40.)
NETWORK 
PASSWORDENTER
  Set the password for the certification of PJLink™, ProjectorView Global+ 
and remote control via LAN. (See page 40.)
IP CONFIG
ENTER...

Menu operation (continued)
EN-33
AMX DEVICE 
DISCOVERYOFF / ON  Use this setting when using an AMX controller.
NETWORK RESET
OK
 Resets the network setting. (See page 45.)
NETWORK 
RESTARTOK
 Press the ENTER button to restart the network function. 

EN-34
Menu operation (continued)
INFORMATION menu
 You can display the INFORMATION menu also by pressing the INFO. button on the remote control.  ITEM DESCRIPTION
LAMP TIME (LOW) This item shows the lamp operation time calculated based on that the LAMP MODE is LOW.
 When the LAMP MODE is STANDARD, this item shows a longer lamp operating time than the
actual time.
 When the lamp operating time is 0 to 10 hours, “0H” is displayed. The lamp operating time
exceeding 10 hours is indicated by the actual...

EN-35
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu. 
(See page 25 for menu setting.) 
1. Display the IMAGE menu. 
2. Select CONTRAST or BRIGHTNESS by pressing the S or T button. 
3. Adjust the selected item by pressing the W or X button. 
To cancel the menu:
4. Press the MENU button. 
CONTRAST
Select to adjust the contrast of the image. Every time the X button is pressed, the image becomes brighter and more 
clearly...

EN-36
Image adjustment (continued)
To adjust the tone of white (COLOR TEMP.): 
You can select a preset color temperature (white tone) using the menu. 
(See page 25 for menu setting.)  
1. Display the IMAGE menu. 
2. Select COLOR TEMP. by pressing the S or T button. 
3. Select your desired color temperature by pressing the W or X button. 
To cancel the menu:
4. Press the MENU button. 
To adjust the tone of white (To customize the color temperature): 
To customize (and store) the color temperature to your...

Image adjustment (continued)
EN-37
BrilliantColor™
Use this setting to make colors with medium brightness, such as yellow and the skin tone appear natural. Press the W 
button to decrease the value to lessen the effect. Press the X button to increase the value to heighten the effect. 
(BrilliantColor™ has no effect at value 0.)
 For more enhanced color reproduction, set BrilliantColor™ to 0. The white area of the color wheel is disabled, and
you can reproduce true-color images.
GAMMA MODE
Use this item...

EN-38
Image adjustment (continued)
How to adjust the computer image
This projector automatically selects a proper signal format according to the type of video signal supplied from the 
computer. However, video signals from the computer may not be projected correctly depending on the types of the 
computer and images to be projected. In such a case, make adjustment according to the flowchart below.
Adjustment is completed. When the size and position of 
the computer image are not correct. 
Project a...

Image adjustment (continued)
EN-39
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms.
1. Display the SIGNAL menu.
2. Press the S or T button to select a setting to adjust.
3. Adjust the selected setting by pressing the W or X button.
To cancel the menu:
4. Press the MENU button.
 Do not change the settings of the SIGNAL menu for ordinary use.
LPF (Progressive filter) 
You can select whether or not to enable the LPF. Vertical or...

EN-40
You can set the network of the projector using the 
menu.
Setting Projector Name
(See page 25 for menu setting.)
1. Display the NETWORK menu
2. Press the S or T button to select PROJECTOR 
NAME.
3. Press the ENTER button.
 The PROJECTOR NAME screen appears.
4. Press the direction buttons to move the key cursor, 
select the characters or marks to enter, and press 
the ENTER button.
 Projector Name can be set using up to 15
characters including alphabets (capital/small),
numeric characters, or...