Mitsubishi Sd220u Projector User Manual

EN-11
ENGLISH
Basic connections (continued)
Projector + Computer 
For computer with Mini D-SUB  
For analog connection: 
1. Connect one end of the supplied RGB cable to the COMPUTER IN terminal of the projector.
2. Connect the other end of the RGB cable to the monitor port of the computer. 
Important:  When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly. 
 Some computers require additional connectors or analog RGB output adapters to be connected with...

EN-12
Preparation
Preparation for projection 1. To protect the projector during transportation, protective tapes are adhered to the terminal board of the projector.
Please remove the protective tapes before use.
2. Attach the provided power cord to the projector. 
3. Plug the power cord in the wall outlet. 
Warning:  Do not look into the lens directly when the projector is on. 
 One of power cords for the U.S., Europe and U.K. is provided  appropriately.
 This projector uses the power plug of three-pin...

EN-13
ENGLISH
Basic operation
Power-on 1. Turn on the device connected to the projector first. 
2. Plug the power cord in the wall outlet.  The POWER indicator lights up. 
 If the power cord is unplugged from the wall outlet before the projector is cooled down completely after use, the fans may 
start rotating when the power cord is plugged in next time 
and the POWER button may not function. In this case, wait 
for the fans to stop and press the POWER button to light the 
indicator. 
3. Press the POWER...

EN-14
Basic operation (continued)
Power-off Use the following procedure to turn off the projector.
The lamp may deteriorate if the projector is powered off and on 
repeatedly within 30 minutes after the lamp is lighted.
1.Press the POWER button on the control panel or the STANDBY 
button on the remote control. 
 The message POWER OFF? YES : PRESS AGAIN appears on the screen.
 To cancel, press any button except the POWER button.  (Some buttons on the remote control don’t function for can-
cel.) 
2.Press...

EN-15
ENGLISH
Basic operation (continued)
Wall ScreenThis function is to reproduce natural color tones when images are pro-
jected directly onto a screen or wall surface. You can select from 
BEIGE, LIGHT BLUE, LIGHT GREEN, PINK, BLACK BOARD, WHITE 
BOARD, and OFF, to match the color of the screen or wall to be used 
for projection.
1. Display the INSTALLATION menu. (See page 20 for more details.)
2. Press the S or  T button to select WALL SCREEN.
3. Press the  W or  X button to select the color closest...

EN-16
Menu operation
As one of the two types of MENU display, following QUICK MENU appears on the screen when pressing MENU button on the remote con trol. In 
addition, DETAIL MENU (See page 18) appears when selecting DETAIL MENU in this MENU and pressing ENTER button.
 Comparing QUICK MENU with DETAIL MENU, if the contents in those two menus are same each other, the functions in those two menu s are 
same as well.
 To close QUICK MENU or DETAIL MENU, press MENU button when MENU is displayed.
QUICK...

EN-17
ENGLISH
Menu operation (continued)
Menu OptionsSet the following options provided in the respective menus.
1. QUICK MENU
 You cannot adjust COLOR TEMP. when WALL SCREEN is set to other than OFF.
 When COLOR ENHANCER is switched, projected images may be distorted.
 By default, the LAMP MODE is set to STANDARD. The LAMP MODE is set to either STANDARD or LOW depending on the setting last selected, 
and you cannot switch the LAMP MODE in about one minute after the lamp is on.
2. INFORMATION menu
Menu...

EN-18
Menu operation (continued)
DETAIL MENU* Menus are not displayed when no signal is supplied to the projector.
IMAGE
INSTALLATION
FEATURE
SIGNAL
INFORMATION
COLOR ENHANCER
CONTRASTBRIGHTNESS
COLOR TEMP.
AUTO
THEATER
PRESENTATIONSTANDARD
±30±30STANDARD
COLOR *1TINT *1SHARPNESS *1
ADVANCED MENU
±10±10±5
WALL SCREEN
LAMP MODEAUTO POWER ONAUTO POWER OFFSPLASH SCREENBACK COLOR
IMAGE REVERSE
STANDARD, LOW
OFF, 5, 10, 15, 30, 60 minON, OFF
BLACK BOARDWHITE BOARDOFF
BLUE, BLACKOFF, MIRROR, INVERT, MIRROR...

EN-19
ENGLISH
Menu operation (continued)
Basic operationSeveral settings can be adjusted using the menu.
Example : Auto power off time setting
1. Press the MENU button.
2. Select the DETAIL MENU and press the ENTER button  (or T 
button).
3. Press the  W or  X button to select INSTALLATION. 
4. Press the ENTER button (or  T button). 5. Press the 
S or  T button to select AUTO POWER OFF.
6. Press the  W or  X button to adjust the auto power off time.
7. Exit the menu by pressing the MENU button several...

EN-20
Menu operation (continued)
2. INSTALLATION menu
 By default, the LAMP MODE is set to STANDARD. The LAMP MODE is set to either STANDARD or LOW depending on the setting last selected, 
and you cannot switch the LAMP MODE in about one minute after the lamp is on.
Menu option Setting Feature description
WA LL  SC R EE N OFF/BEIGE / LIGHT 
BLUE / LIGHT 
GREEN / PINK /
BLACK BOARD/WHITE 
BOARD Selects a desired setting based on the color of the screen or wall on 
which images are projected.  (See page...