Mitsubishi Sd220u Projector User Manual

							
EN-11
ENGLISH
Basic connections (continued)
Projector + Computer 
For computer with Mini D-SUB  
For analog connection: 
1. Connect one end of the supplied RGB cable to the COMPUTER IN terminal of the projector.
2. Connect the other end of the RGB cable to the monitor port of the computer. 
Important:  When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly. 
 Some computers require additional connectors or analog RGB output adapters to be connected with this projector. Contact your dealer for fur-
ther information. 
 This projector uses stereo mini jack for its audio input. Chec k the type of the audio output terminal of the connected compute r and prepare a 
proper cable for connection. Some computers don’t have the audio output terminal. 
 Speaker output is mono. 
For Macintosh  If your Macintosh has no video port, a monitor output adapter is required. Contact your dealer for further information. 
 Some Macintoshes require a MAC adapter for the RGB cable for connection with this projector. Contact your dealer for further i nformation. 
About DDCThe COMPUTER/COMPONENT VIDEO IN terminal of this projector complies with the DDC 1/2B standard. When a computer supporting this  stan-
dard is connected to this terminal, the computer will automatica lly load the information from this projector and prepare for output of appropriate 
images.
 After connecting a computer supporting this standard to this term inal, plug the power cord of the projector in the wall outlet first, and then boot up 
the computer.
COMPUTER IN RGB cable for PC
PC audio cable (option)
AU D I O I N
to PC audio outputComputer
to monitor port 
						

							
EN-12
Preparation
Preparation for projection 1. To protect the projector during transportation, protective tapes are adhered to the terminal board of the projector.
Please remove the protective tapes before use.
2. Attach the provided power cord to the projector. 
3. Plug the power cord in the wall outlet. 
Warning:  Do not look into the lens directly when the projector is on. 
 One of power cords for the U.S., Europe and U.K. is provided  appropriately.
 This projector uses the power plug of three-pin grounding type. Do  not remove the grounding pin from the power plug. If the power 
plug doesn’t fit your wall outlet, ask an electrician to change the 
wall outlet. 
 In case that the power cord for the U.S is provided with this projec- tor, never connect this cord to any outlet or power supply using 
other voltages or frequencies than rated. If you want to use a 
power supply using other voltage than rated, prepare an appropri-
ate power cord separately.
 Use 100-240 V AC 50/60 Hz to prevent fire or electric shock. 
 Do not place any objects on the power cord or do not place the  projector near heat sources to prevent damage to the power cord. 
If the power cord should be damaged, contact your dealer for 
replacement because it may caus e fire or electric shock. 
 Do not modify or alter the power cord. If the power cord is modified  or altered, it may cause fire or electric shock. 
Caution:  Plug in the power cord firmly. When unplugging, hold and pull the power plug, not the power cord. 
 Do not plug in or out the power cord with your hand wet. It may  cause electric shock. 
Adjustment of the projection angle For the best projection, project images on a flat screen installed at 90 
degrees to the floor. If necessary, tilt the projector using the two 
adjustment feet on the bottom of the projector.
Using the adjustment feet (front)1. Tilt up the projector to the appropriate angle. 
2. Rotate the adjustment feet (front) for fine adjustment. 
Important:  Install the screen on a flat wall at 90 degrees to the floor. 
 Slanting the projector more than ±10° (right and left) or ±15° (front and rear) may cause trouble or explosion of the lamp. You can tilt 
the projector up to 8 degrees using the adjustment feet only. 
 Images may not be projected in a shape of a regular rectangle or  with its aspect ratio 4:3, depending on the installation conditions of 
the projector and the screen. 
 To correct vertical keystone distortion, press the KEYSTONE but- ton on the remote control to display KEYSTONE, and adjust the 
image by pressing the VOLUME  S, T  button. 
In the following cases:  
Important: 
 When the keystone adjustment is carried out, the adjustment 
value is indicated. Note that this value doesn’t mean a projection 
angle. 
 The allowable range of the adjustment value in the keystone  adjustment varies depending on the installation conditions. 
 When the keystone adjustment takes effect, the resolution  decreases. In addition, stripes may appear or straight lines may 
bend in images with complicated patterns. They are not due to 
product malfunctions. 
 Noise may appear on the screen during the keystone adjustment  because of the type of the vid eo signal being projected and the 
setting values of the keystone adjustment. In such cases, set the 
keystone adjustment values in the range where the image is dis-
played without noise. 
 When the keystone adjustment is carried out, the image may not  be displayed correctly because of the type of input signal.
Protective Tapes
Press the  T  
button. Press the 
S  
button. 
						

							
EN-13
ENGLISH
Basic operation
Power-on 1. Turn on the device connected to the projector first. 
2. Plug the power cord in the wall outlet.  The POWER indicator lights up. 
 If the power cord is unplugged from the wall outlet before the projector is cooled down completely after use, the fans may 
start rotating when the power cord is plugged in next time 
and the POWER button may not function. In this case, wait 
for the fans to stop and press the POWER button to light the 
indicator. 
3. Press the POWER button on the control panel or the ON button  on the remote control. 
 It may take about one minute for the lamp to light up. 
 The lamp occasionally fails to light up. Wait a few minutes and try to light the lamp again. 
 After the POWER button is pressed, the image may flicker  before the lamp becomes stable. This is not a product mal-
function. 
 Regardless of the setting of LAMP MODE in the INSTALLA- TION menu, the STANDARD lamp mode is activated by 
default whenever the projector is turned on. The LAMP 
MODE is set to either STANDARD or LOW depending on the 
setting last selected, and you cannot switch the LAMP 
MODE in about one minute after the lamp is on.
Important:  If the lamp exceptionally turned off due to the power interruption or voltage drop, it can happen that the lamp does not turn on even if 
you switch again the power supply on. In that case, please pull the 
electric cord out of the consent and put it again in the consent 
about 10 minutes later.
 The projector starts warming up when the POWER button is  pressed. During the warm-up process, images may appear dark 
and no commands are accepted.   By blinking red, the STATUS indicator indicates that the lamp 
should be replaced soon. Replace the lamp when the STATUS 
indicator blinks red. (See page 28 and 31.) 
 Images may not be projected with good quality in an extremely hot  or cold environment. (This is not a product malfunction.) 
 In order to ensure the safety in case of trouble with the projector,  use an electrical outlet having an  earth leakage breaker to supply 
the power to the projector. If you do not have such outlet, ask your 
dealer to install it.
4. Adjust the focus by turning the focus ring. 
5. Choose your desired external input source using the SOURCE  or COMPUTER or VIDEO button.
 Each press of SOURCE button of the Control Panel enables the input source to switch in  the following order: COMPUTER 
and VIDEO.
 When pressing COMPUTER or VIDEO button on the remote  control, the input source switches directly as the button 
pressed. 
 The projector automatically selects the appropriate signal  format. The selected signal format is displayed on the 
screen. 
 The SOURCE, COMPUTER and VIDEO buttons don’t func- tion while the menu is being displayed. 
 When COMPUTER is chosen  as the source, images sup-
plied from the computer may flicker. Press the  W or  X button 
on the remote control to reduce flicker, if it occurs. 
 To avoid permanently imprinting a fixed image onto your pro- jector, please do not display the same stationary images for 
long period.
6. Adjust the image size by turning the zoom ring.  If necessary, adjust the focus and zoom again.When fine streaks are seen on projected imagesThis is due to interference with the screen surface and is not a mal-
function. Replace the screen or displace the focus a little.
STANDBY
ON
ASPECT
MAGNIFY
KEYSTONE VO L PAG E
UP
DOWN
MENU
FREEZE
AU T O
POSITION
AV
MUTE ENTER
1
2COMPUTER
VIDEOVIEWER
UNPLUGS
-
VIDEO
WIRELESS DVI
4  FOCUS
6  ZOOM
5
3,  1, 2 5 1, 2
3
Indicator
Condition STATUS POWER
Stand-by - Red
When the lamp is on. Green Green 
						

							
EN-14
Basic operation (continued)
Power-off Use the following procedure to turn off the projector.
The lamp may deteriorate if the projector is powered off and on 
repeatedly within 30 minutes after the lamp is lighted.
1.Press the POWER button on the control panel or the STANDBY 
button on the remote control. 
 The message POWER OFF? YES : PRESS AGAIN appears on the screen.
 To cancel, press any button except the POWER button.  (Some buttons on the remote control don’t function for can-
cel.) 
2.Press the POWER button on the control panel or the STANDBY 
button on the remote control within 10 seconds again. 
 The lamp will go out and the STATUS indicator will start blinking. 
 Though the lamp goes out at this second press of the  POWER button (or STANDBY button), the air outlet fans con-
tinue operating for one minute to cool down the lamp. The 
STATUS indicator will stop blinking. 
 After stopping the air outlet fans, if the temperature inside the  set is still high, the temperatur e sensor detects it and then 
the air outlet fans may start again.
3.Unplug the power cord. 
 The POWER indicator will go out. 
 If the power cord should be unplugged accidentally while  either the air inlet fan or the air outlet fans are operating or 
the lamp is on, allow the projector to cool down for 10 min-
utes with the power off. To light the lamp again, press the 
POWER button (or ON button). If the lamp doesn’t light up 
immediately, repeat pressing the POWER button (or ON but-
ton) two or three times. If it s hould still fail to light up, replace 
the lamp. 
Notice: When storing the projector in the carrying case, the lens should  face up.
Instant Shut DownYou dont have to wait for the cooling fan to cease operation after pow-
ering off the projector. You can unplug the power cord right after the 
projector is powered off.
 Dont shut down the projector while the STATUS indicator is blink-ing after the lamp lights up because the lamps life may be short-
ened.
 Dont turn the projector back on right after shutting it down  because the lamps life may be shortened. (Wait about 10 minutes 
before turning the projector back on.)
 Before shutting down the projector, be sure to close the menu  screen. If you shut down the projector without closing the menu, 
the setting data of the menu may not be saved.
AUTO POSITION button When the image isn’t projected in the right position with COMPUTER 
selected as the input source, follow the procedure below. 
1. Project a bright image such as the Recycle Bin window on the  full screen. 
2. If the screen saver is running, turn it off. 
3. Press the AUTO POSITION button.   If the image is still not in the right position, adjust the image position using the SIGNAL menu. See page 22. 
Volume from the speaker Press the VOLUME  S or  T button to change the volume 
from the speaker.
The volume control bar will appear on the screen.
 The volume control bar will disappear about 10 seconds after the  VOLUME button is released. 
 The VOLUME buttons don’t function while the menu selection bar  or the menu is being displayed. 
 When a high-level audio signal, such as a DVD audio signal, is  supplied to the AUDIO IN terminal, the output from the speaker 
may be distorted. 
AV  m u t e  The video and audio signals are temporarily muted when the AV 
MUTE button is pressed. To cancel muting, press the AV MUTE button 
again. 
Setting the aspect ratioYou can change the aspect ratio of the input video signal (or the ratio 
of width to height of the image). Change the setting according to the 
type of the input video signal.
How to change the settings:
With the remote control:
1. Press the ASPECT button.  Every time the ASPECT button is pressed, the aspect mode changes from NORMAL to 16:9, to FULL, and back to NOR-
MAL.
With the FEATURE menu:(See page 21 for menu setting.)
1. Display the FEATURE menu.
2. Select ASPECT by pressing the  S or  T button.
3. Select your desired aspect ratio by pressing the  W or  X button.
When 16:9  is selected.
4. Press the ENTER button.
5. Select your desired position (CENTER, UPPER or LOWER) by  pressing the  W or  X button.
To cancel the menu:
6. Press the MENU button.
Important: When a 16:9 image is kept displayed for a long time before dis-
playing 4:3 image, the afterimages of the black bars may appear 
on the 4:3 image screen. Consult your dealer in this case.
Caution:  After using the projector, wait one minute for the air outlet fans to stop in normal use. Then unplug the power cord from the wall out-
let. 
 The lamp can’t be lit again for one minute after turned off for safety  purpose. It will take another one minute for the STATUS indicator 
to go out. If you want to turn on the projector again, wait until the 
indicator goes out, and then press the POWER button. 
 The air outlet fans rotate faster as the temperature around the pro- jector rises. 
 When the temperature around the projector rises high, the sign  TEMPERATURE!! blinks red on the screen. If the temperature 
stays high, the lamp will go out automatically. 
Important:  Do not display a still picture for  a long time because the afterim-
ages may persist on the screen.
VOLUME     10
FEATURENORMAL
opt.
ASPECT 
						

							
EN-15
ENGLISH
Basic operation (continued)
Wall ScreenThis function is to reproduce natural color tones when images are pro-
jected directly onto a screen or wall surface. You can select from 
BEIGE, LIGHT BLUE, LIGHT GREEN, PINK, BLACK BOARD, WHITE 
BOARD, and OFF, to match the color of the screen or wall to be used 
for projection.
1. Display the INSTALLATION menu. (See page 20 for more details.)
2. Press the S or  T button to select WALL SCREEN.
3. Press the  W or  X button to select the color closest to that of the 
screen on which images are projected.
 When the GAMMA mode setting is changed, images may not  be displayed correctly.
 When OFF or BLACK BOARD/WHITE BOARD is selected,  the density cannot be adjusted.
 When WHITE BOARD is selected, BrilliantColor
TM in the 
Color Enhancer menu of the Image menu cannot be used. 
Additionally, Theater in the Color Enhancer menu of the 
Image menu has no effect and is automatically canceled 
when WHITE BOARD is selected.
4. Press the ENTER button.
5. Press the  W or  X button to adjust the density of the selected 
color.
When connecting to a laptop computer:When this projector is connected to a laptop computer, there may be 
times when images may not be projected. When it occurs, set the 
computer so that it can output signals externally. The procedure varies 
across computers in use. See the instruction manual of your com-
puter.
INSTALLATION
opt.
WALL SCREEN
LAMP MODE BEIGE
STANDARD
LIGHT BLUE 1 
						

							
EN-16
Menu operation
As one of the two types of MENU display, following QUICK MENU appears on the screen when pressing MENU button on the remote con trol. In 
addition, DETAIL MENU (See page 18) appears when selecting DETAIL MENU in this MENU and pressing ENTER button.
 Comparing QUICK MENU with DETAIL MENU, if the contents in those two menus are same each other, the functions in those two menu s are 
same as well.
 To close QUICK MENU or DETAIL MENU, press MENU button when MENU is displayed.
QUICK MENU* Menus are not displayed when no signal is supplied to the projector.
QUICK MENU Basic operationSeveral settings can be adjusted using the menu.
Example : Contrast setting
1. Press the MENU button.
2. Press the ENTER button (or  T button). 3. Press the 
S or  T button to select CONTRAST.
4. Press the  W or  X button to adjust the contrast.
5. Exit the menu by pressing the MENU button several times.
Important:  When the button doesn’t function, unplug the power cord from the  wall outlet. Wait about 10 minutes, plug the power cord in, and try 
again.
 After selecting the items marked with  , press the ENTER but- ton.
QUICK MENU COLOR ENHANCER
CONTRA STBRIGHTNE SS
COLOR TEMP.
AUTO
THEATERU SER
PRE SENTATIONSTANDARD
±30S TANDARD
S HARPNE SS * 1
±5
LAMP MODE  A SPECT
U SER MENU
S ELECT U SER MENU
STANDARD, LOW
COLOR
LOWHIGHU SER
INFORMATION
SYNC. TYPE  *2
LAMP TIME (LOW)
INPUT
RE SOLUTION
VERTICAL FREQUENCY
HORIZONTAL FREQUENCY
± 30
WALL  SCREENTINT
WXGALANGUAGE
NORMAL, 16:9, FULL 
DETAIL MENU
OK
IMAGE REVER SEMENU PO SITIONCINEMA MODE
*1 Not available with certain signals
*2 Not available when the input signal is from the VIDEO IN terminal.
QUICK MENU
QUICK MENU
AUTOCOLOR
ENHANCER
0CONTRAST
+10CONTRAST 
						

							
EN-17
ENGLISH
Menu operation (continued)
Menu OptionsSet the following options provided in the respective menus.
1. QUICK MENU
 You cannot adjust COLOR TEMP. when WALL SCREEN is set to other than OFF.
 When COLOR ENHANCER is switched, projected images may be distorted.
 By default, the LAMP MODE is set to STANDARD. The LAMP MODE is set to either STANDARD or LOW depending on the setting last selected, 
and you cannot switch the LAMP MODE in about one minute after the lamp is on.
2. INFORMATION menu
Menu option Setting Feature description
COLOR ENHANCER AU TO
Automatically sets an optimal color balance based on the input signal. 
Use this setting for most cases.
PRESENTATION Makes projected images bright and crisp.
STANDARD Makes projected images look natural.
THEATER Makes projected images soft and smooth. Best suited for movies.
USER Reflected by the value set in IMAGE menu. (See page 23.)
CONTRAST ±30 Adjusts the contrast of projected images. (See page 23.)
BRIGHTNESS ±30 Adjusts the brightness of projected images. (See page 23.)
COLOR TEMP. 4 options Adjusts the color temperature. You cannot select this setting when 
WALL SCREEN in the INSTALLATION menu is set to a setting other 
than OFF. (See page 23.)
SHARPNESS ±5 Adjusts the sharpness of projected images. (See page 23.)
LAMP MODE STANDARD Select this setting when you want to view images in a well-lit room.
LOW
Select this setting when you want to view images at a moderate light 
intensity. The operating sound is consequently reduced, and the lamp 
lifetime becomes longer.
 When this mode is switched, projected images may flicker.
 If this mode is frequently switched, the lamp may be deteriorated.
ASPECT NORMAL
Automatically sets the aspect ratio in relative to the input signal. Use this 
setting for most cases.
16:9 Selects a desired screen position for anamorphically squeezed or hori-
zontally compressed images stored on DVD disks.
FULL Select this setting when you want to project images in the full screen.
USER MENU Displays the menu item selected in SELECT USER MENU.
SELECT USER MENU Select the it em to display in USER MENU.
DETAIL MENU Moves to DETAIL MENU.
Menu option Feature description
LAMP TIME (LOW) This menu shows a lamp operating time (hour) calculated assuming that LAMP MODE is LOW.
 When the LAMP MODE is STANDARD, this menu shows a longer lamp operating time than 
the actual time. (See page 27 for the interval of lamp replacement.)
 When the lamp operating time is 0 to 10 hours, 0H is displayed. When the lamp operating  time exceeds 10 hours, the actual hours are displayed.
 When the lamp operating time reaches 3000 hours, the bar turns yellow. When it reaches  3800 hours, the bar turns red.
(The lamp lifetime is 4000 hours.)
INPUT Indicates the name of the terminal to which the currently projected video signal is being input.
RESOLUTION Indicates the resolution of the currently projected video signal.
VERTICAL FREQUENCY Indicates the vertical frequency of the currently projected video signal.
HORIZONTAL FRE-
QUENCY Indicates the horizontal frequency of the currently projected video signal.
SYNC. TYPE Indicates the type of the sync sign al for the currently projected video signal.
DETAIL MENU
SELECT
USER MENU
ASPECT
USER MENU
NORMAL
OK
COLOR
QUICK MENU
CONTRAST
BRIGHTNESS0
0
STANDARD
STANDARD 0
COLOR TEMP.
SHARPNESS
AUTO
COLOR
ENHANCER
LAMP MODE
INFORMATION
LAMP TIME  (LOW)
INPUT
RE
SOLUTIONVERTICAL
FREQUENCY
HORIZONTAL
FREQUENCY
SYNC. TYPE 5wire 60.02 KHz75.04 Hz
1024x76
8
COMPUTER 0 HRG
HV B 
						

							
EN-18
Menu operation (continued)
DETAIL MENU* Menus are not displayed when no signal is supplied to the projector.
IMAGE
INSTALLATION
FEATURE
SIGNAL
INFORMATION
COLOR ENHANCER
CONTRASTBRIGHTNESS
COLOR TEMP.
AUTO
THEATER
PRESENTATIONSTANDARD
±30±30STANDARD
COLOR *1TINT *1SHARPNESS *1
ADVANCED MENU
±10±10±5
WALL SCREEN
LAMP MODEAUTO POWER ONAUTO POWER OFFSPLASH SCREENBACK COLOR
IMAGE REVERSE
STANDARD, LOW
OFF, 5, 10, 15, 30, 60 minON, OFF
BLACK BOARDWHITE BOARDOFF
BLUE, BLACKOFF, MIRROR, INVERT, MIRROR INVERT
LOW
GAMMA MODEBrilliantColor TMRGB-COLOR RGB-TINT
HIGHCONTRAST RCONTRAST GCONTRAST BBRIGHTNESS RBRIGHTNESS GBRIGHTNESS B
NOISE REDUCTION *1CTI *1
INPUT LEVEL
DYNAMIC, NATURAL, DETAIL0-10±10±10
±30±30±30±30±30±30
ON, OFFON, OFF±5
1-51-51-51-5
 ASPECT
SETUP *1LANGUAGERESET ALL
PASSWORD FUNCTIONMENU POSITIONCINEMA MODE *3 VIDEO SIGNAL *5
NORMAL
AUTO, OFF, 3.75%, 7.5%
DISPLAY INPUT      , MENU ACCESS           1 (upper left),  2 (lower right)
FULL
AUTO, OFFAUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60
LOCK
*4
*4
*4
*4
CENTER, UPPER, LOWER
OVER SCANHOLD *2
LAMP TIME RESET
HORIZ. POSITIONVERT. POSITIONFINE SYNC. *1 *2TRACKING *2
COMPUTER INPUT *2
100-90%OFF
0-9990-9990-310-2800AUTO, RGB, YCBCR/YPBPR
BEGINEND
SHUTTER (L)SHUTTER (LS)SHUTTER (RS)
CLAMP POSITION *2CLAMP WIDTH *2VERT. SYNCLPF *1 *2
SHUTTER (U)
0-990-99
0-200-200-20
1-2551-63AUTO, OFFON, OFF0-20
SYNC. TYPE *2
LAMP TIME (LOW)INPUTRESOLUTIONVERTICAL FREQUENCYHORIZONTAL FREQUENCY
OK     UNLOCKOK     
OK     
USEROK     
ON     
OK     
USER     
USER     
OK     
BEIGE     LIGHT BLUE     LIGHT GREEN     PINK     
16:9     
ON, OFF
, SVENSKA, POLSKI
WXGA *2OFF, AUTO, 1280 x 768, 1280 x 768RB, 1360 x 768, 1366 x 768
*1 Not available with certain signals
*2 Not available when the input signal is from the VIDEO IN terminal.
*3 Available only when the input signal is TV60, TV50, 480i, or 576i.
*4 The range that can be specified varies across input signals.
*5 Available only when the input signal is from the VIDEO IN terminal. 
						

							
EN-19
ENGLISH
Menu operation (continued)
Basic operationSeveral settings can be adjusted using the menu.
Example : Auto power off time setting
1. Press the MENU button.
2. Select the DETAIL MENU and press the ENTER button  (or T 
button).
3. Press the  W or  X button to select INSTALLATION. 
4. Press the ENTER button (or  T button). 5. Press the 
S or  T button to select AUTO POWER OFF.
6. Press the  W or  X button to adjust the auto power off time.
7. Exit the menu by pressing the MENU button several times.
Important:  When the button doesn’t function, unplug the power cord from the  wall outlet. Wait about 10 minutes, plug the power cord in, and try 
again.
 After selecting the items marked with  , press the ENTER but- ton.
Menu OptionsSet the following options provided in the respective menus.
1. IMAGE menu
 You cannot adjust TINT when the TV50 (PAL, SECAM) signal is inputted.
 You cannot adjust COLOR TEMP. when WALL SCREEN is set to other than OFF.
 When COMPUTER is selected, COLOR and TINT do not work.
 When COLOR ENHANCER is switched, projected images may be distorted.
IMAGE
opt.
INSTALLATION
opt.
INSTALLATION
opt.
WALL SCREEN BEIGE
OFF
AUTO POWER 
ON
OFFAUTO POWER OFF
30min
AUTO POWER 
ON
OFFAUTO POWER OFF
Menu option Setting Feature description
IMAGE ADVANCED menu
COLOR ENHANCER AU TO
Automatically sets an optimal color balance based on the input signal. 
Use this setting for most cases.
PRESENTATION Makes projected images bright and crisp.
STANDARD Makes projected images look natural.
THEATER Makes projected images soft and smooth. Best suited for movies.
USER
 Adjusts the gamma curve, color intensity, or balance. (See page 23.)
CONTRAST ±30 Adjusts the contrast of projected images. (See page 23.)
BRIGHTNESS ±30 Adjusts the brightness of projected images. (See page 23.)
COLOR TEMP. 4 options Adjusts the color temperature. You cannot select this setting when 
WALL SCREEN in the INSTALLATION menu is set to a setting other 
than OFF. (See page 23.)
COLOR ±10 Adjusts the color tone of projected images. (See page 23.)  You cannot 
select this setting when the COMPUTER is selected as the input source.
TINT ±10 Adjusts the color tint of projected images.  (See page 23.) You can 
select this setting only when NTSC 
is selected as the input signal.
SHARPNESS ±5 Adjusts the sharpness of projected images. (See page 23.)
ADVANCED MENU OK
 NOISE REDUCTIONON/OFF Reduces noise of projected images when the input signal is noisy.
CTI ON/OFF Corrects sm eared color borders.
INPUT LEVEL ±5 Adjusts the input level of analog video signals.
The input level of the video signal varies across devices to which the 
projector is connected. A high input level causes projected images to 
appear solid white, and a low input level causes projected images to 
appear dark.
IMAGE
opt.
CONTRAST
BRIGHTNESS0
0
STANDARD
0 0
OK
COLOR
TINT
ADVANCED MENU
COLOR TEMP.
0
SHARPNESS
AUTO
COLOR
ENHANCER
IMAGEADVANCED MENU
CTI
INPUT LEVEL
0
ON
ON
NOISE REDUCTION
opt. 
						

							
EN-20
Menu operation (continued)
2. INSTALLATION menu
 By default, the LAMP MODE is set to STANDARD. The LAMP MODE is set to either STANDARD or LOW depending on the setting last selected, 
and you cannot switch the LAMP MODE in about one minute after the lamp is on.
Menu option Setting Feature description
WA LL  SC R EE N OFF/BEIGE / LIGHT 
BLUE / LIGHT 
GREEN / PINK /
BLACK BOARD/WHITE 
BOARD Selects a desired setting based on the color of the screen or wall on 
which images are projected.  (See page 15.) When selecting a setting 
other than BLACK BOARD/WHITE BOARD, you can fine-tune the color 
tone to the desired level on the 1 to 5 scale.
LAMP MODE STANDARD Select this setting when you want to view images in a well-lit room.
LOW
Select this setting when you want to view images at a moderate light 
intensity. The operating sound is consequently reduced, and the lamp 
lifetime becomes longer.
 When this mode is switched, projected images may flicker.
 If this mode is frequently switched, the lamp may be deteriorated. 
AUTO POWER ON ON/OFF When this mode is set to ON, the lamp is automatically lit when the 
power cord is plugged in the wall outlet. Select ON when you set the 
projector at the ceiling.
 When the lamp is off, the projector is in standby. Use the remote 
control to turn on the lamp.
AUTO POWER OFF OFF/5-60 min Selects a desired timer setting until the projector enters the standby 
mode when there is no signal input from the source.
SPLASH SCREEN ON/OFF Select ON to display the splash screen when the projector is powered on.
BACK COLOR BLUE/BLACK Selects the background color that is displayed when there is no signal 
input from the source. 
IMAGE REVERSE OFF
Select this setting when you want to 
view images from the front with the 
projector set on the floor.
MIRROR Select this setting when you want to view images from behind the 
screen with the projector set on the floor.
INVERT Select this setting when you want to view images from behind the 
screen with the projector set at the ceiling.
MIRROR INVERT Select this setting when you want to 
view images from the front with the 
projector set at the ceiling.
LAMP TIME RESET OK
 Resets LAMP TIME.
INSTALLATION
opt.
ONSPLASH 
SCREEN
WALL SCREEN
LAMP MODE
BEIGE
ON
STANDARD
OFF
IMAGE 
REVERSE
AUTO POWER 
OFF
OFF OFF
AUTO POWER ON
BACK COLORBLUE
LAMP TIME
RESETOK