Mitsubishi Projector Xd205u User Manual

EN-21
ENGLISH
Password function 
This projector is equipped with the password function that is 
designed for prevention of wrong operation by children and 
restriction on operation by other than specified users.  
MENU ACCESS ............ All the buttons except for the POWER 
button on the projector are di sabled. (The buttons on the 
remote control are enabled.) You can use this mode as a 
measure of preventio n of wrong operation by children and 
restriction on operation by other than specified users....

EN-22
Lamp replacement
When the lamp no longer functions, replace it with a new one.
Caution:
 Do not remove the lamp immediately after using the projec-tor. You may get burned because the lamp very hot after 
use.
 Before replacing the lamp, press the POWER button to turn  off the lamp and wait for two minutes for lamp to cool down. 
Unplug the power cord from wall outlet and wait one hour 
for the lamp to cool down completely.
 Do not remove the lamp except for replacement. Careless  handling can...

EN-23
ENGLISH
Troubleshooting
The following offers solutions to some of the common problems you may encounter. We suggest that you consult this chart before 
contacting your dealer. 
Images aren’t projected on the screen. 
 
ProblemCause and solution 
Power isn’t turned on.   Check the states of the indicators. 
Images aren’t projected on the screen.  Cancel the AV mute by pressing the MUTE button. 
 Remove the lens cap. 
 The lamp sometimes takes about one minute to light up. 
 On rare occasion,...

EN-24
Troubleshooting (continued)
Images aren’t projected correctly.
ProblemCause and solution 
Projected images are shaking.
Projected images are displaced.  Check that the cable connected to the external device isn’t intermittent. 
 Connect the cable’s plug with the external device’s connector firmly. 
 Press the AUTO POSITION button. 
 Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu. (See 
page 19.) 
Projected images are distorted.   Adjust the projector and...

EN-25
ENGLISH
Others
When the problems below occur after the lamp is replaced, check the following.
Maintenance 
Caution: 
Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector . 
Cleaning of the projector and the ventilation slots 
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened 
with diluted mild detergent, and t hen wipe them with a dry...

EN-26
Indicators
This projector has two indicators, each of which shows the operation condition of the projector. 
The following offer solutions to possible problems. If these pr oblem persist, turn the projector off and consult your dealer.
Normal condition
Abnormal condition
POWERSTATUSCONDITIONNOTE
Stand-by
Lamp stand-by (about 1 minute) The POWER button cannot be used to switch 
between on and off.
The power is on. (Normal condition)
STATUS indicator POWER indicator
Steady redOff
Steady...

EN-27
ENGLISH
Specifications
 The specifications and outside appearance of the projector are su bject to change without prior notice. 
Kensington Lock 
This projector has a Kensington Security Standard connector fo r use with Kensington MicroSaver Security System. Refer to the infor-
mation that came with the Kensington System for instructions on  how to use it to secure the projector. Please contact Kensington 
Technology Group below. 
Kensington Technology Group 
2855 Campus Drive 
San Mateo, CA...

EN-28
Specifications (continued)
Connectors
Dimensional drawings (unit : mm)
What’s included in the box
Replacement part
15
11
6 10
15
pin No.Spec.
1 R(RED)/C
R
2 G(GREEN)/Y
3B(BLUE)/C
B
4GND
5GND
6GND
7GND
8GND
9 DDC5V
10 GND
11 GND
12 DDC Data
13 HD/CS
14 VD
15 DDC Clock
pin No.Spec.
1R(RED)/C
R
2 G(GREEN)/Y
3B(BLUE)/C
B
4-
5GND
6GND
7GND
8GND
9-
10 GND
11 -
12 -
13 HD/CS
14 VD
15 -
COMPUTER IN/OUT (Mini D-SUB 15-pin)
IN OUT
    AC power cord
1  RGB cable for PC
1  VIDEO cable for US
for EU
for UK...

EN-29
ENGLISH
Specification of RGB signals in each computer mode of the projector 
Important:
 Some computers aren’t compatible with the projector.
 The projector’s maximum resolution is 1024 x 768 pixels (800 x 600 pixels for SD205U). It may not display images of 
higher resolutions than 1024 x 768 (or 800 x 600) correctly.
 Images with SYNC on G (Green) signal may jitter.
 Images with SYNC on G (Green) signal may be tinged with  green.
 If the resolution and frequency of your computer aren’t...

MITSUBISHI ELECTRIC CORPORATION
MITSUBISHI Projector Contact Information
North America MESCA (Mitsubishi Electric Sales Canada Inc.)
http://www.mitsubishielectric.ca
Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2, 
Canada
Sales Phone :+1-(905) 475-7728
Fax :+1-(905) 475-7958
E-mail :[email protected] 
Technical Phone :+1-(905) 475-7728
Fax :+1-(905) 475-7958 
Customer Care E-mail :[email protected] 
MDEA (Mitsubishi Digital Electronics America,...