Mitsubishi Projector Xd205u User Manual

EN-11
ENGLISH
Projector + Computer 
For computer with Mini D-SUB  
Important: 
 When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly. 
 Some computers require additional connectors  or analog RGB output adapters to be connected with this projector. Contact your 
dealer for further information. 
 This projector uses stereo pin jack for its audio input. Check t he type of the audio output terminal of the connected computer and 
prepare a proper cable...

EN-12
Preparation
Preparation for projection 
1. Attach the provided power cord to the projector. 
2. Plug the power cord in the wall outlet. 
3. Remove the lens cap. 
Warning: 
 Do not look into the lens directly when the projector is on. 
 The lens cap is for protecting the lens. If you leave the lens cap on the lens with the projector turned on, it may be 
deformed because of heat build-up. Remove the lens cap 
when you turn on the projector. 
 The power cords for use in the U.S. and Europe are...

EN-13
ENGLISH
Basic operation
Power-on 
1. Turn on the device connected to the projector first. 
2. Plug the power cord in the wall outlet.  The POWER indicator lights up. 
 If the power cord is unplugged from the wall outlet before the projector is cooled down completely after 
use, the fans may start rotating when the power cord is 
plugged in next time and the POWER button may not 
function. In this case, wait for the fans to stop and press 
the POWER button to light the indicator. 
3. Press the...

EN-14
Basic operation (continued)
Power-off 
Use the following procedure to turn off the projector. Do not 
turn off the projector by unplugging the power cord while the 
lamp is on. Unplugging while the lamp is on degrades the 
lamp’s performance and causes failure in the projector. 
1.Press the POWER button on the  control panel or the OFF 
button on the remote control. 
 The message POWER OFF? YES : PRESS AGAIN  appears on the screen.
 To cancel, press any button except the POWER button.  (Some...

EN-15
ENGLISH
Menu operation
Basic operation
Several settings can be adjusted using the menu. OFF.
Example : Auto power off time setting
1. Press the MENU button.
2. Press the W or  X button to select INSTALLATION. 
3. Press the ENTER button (or  T button). 4. Press the 
S or  T button to select AUTO POWER OFF.
5. Press the  W or  X button to adjust the auto power off time.
6. Exit the menu by pressing the MENU button several times.
Important: 
 When the button doesn’t function, unplug the power cord...

EN-16
Menu operation (continued)
1IMAGE
CONTRAST ................................. Use to adjust the image contrast. The contrast 
becomes higher as the value increases.
BRIGHTNESS ......... .................... Use to adjust the image brightness. The image 
becomes brighter as the value increases.
WHITE ENHANCE ...................... Use to adjust  the white level of the projected image. 
Select AUTO for normal use.
COLOR TEMP ............................. Use to adjust the color temperature. See page...

EN-17
ENGLISH
3 FEATURE
MENU POSITION ....................... Use to select the position of the menu on the screen, 
1.   (upper left) or 2.   (lower right). 
CINEMA MOD ............................. When AUTO  is selected, the film mode will be auto-
matically activated when a film source signal is input-
ted. When OFF is selected, the film mode will not be 
activated.
VIDEO SIGNAL ........................... When AUTO  is selected, the appropriate video format 
is automatically selected depending on...

EN-18
Image adjustment
Image adjustment
You can adjust the image using the IMAGE menu. 
To control the white-to-black level of the image : 
Adjust CONTRAST in the IMAGE menu. Press the  X button to 
increase the contrast and the  W button to reduce it. 
To control the light level of the image : 
Adjust BRIGHTNESS in t he IMAGE menu. Press the  X button 
to lighten the image and the  W button to darken it. 
To determine the intensity of the color : 
Adjust COLOR in the IMAGE menu. Press the  X button to...

EN-19
ENGLISH
Adjustment of the image from the computer 
This projector adjusts the format of the video signal supplied 
from the computer. However, sometimes images are not pro-
jected correctly owing to the type of the computer used. When 
the image from the computer is n’t projected correctly, press 
the AUTO POSITION button. (See  page 14.) If the image isn’t 
projected correctly yet, adjust  the image from the computer 
using the menu.  
To move the image horizontally : 
Adjust HORIZ. POSITION in...

EN-20
Advanced feature
Still 
To stop the motion in the image temporarily (or to display a still 
image):
Press the STILL button on the remote control.
 The image will freeze temporarily. 
To resume the motion in the image: 
Press the STILL button on the remote control again. 
Important: 
 Do not display a still picture for a long time because the afterimages may persist on the screen. 
Page-up and page-down 
You can control the computer  to page-up and page-down the 
presentation data using the remo...