Mitsubishi Projector Xd205u User Manual

							
EN-21
ENGLISH
Password function 
This projector is equipped with the password function that is 
designed for prevention of wrong operation by children and 
restriction on operation by other than specified users.  
MENU ACCESS ............ All the buttons except for the POWER 
button on the projector are di sabled. (The buttons on the 
remote control are enabled.) You can use this mode as a 
measure of preventio n of wrong operation by children and 
restriction on operation by other than specified users. 
To enable the password function: 
1. Display the FEATURE menu. 
2. Press the  S or  T button to select PASSWORD FUNC-
TION. 
3. Press the ENTER button.   The screen for setting the password function will appear.
 When the password has already been set, the mode  won’t be changed. In such cases, press the ENTER 
button to cancel the password function and try again. 
4. Press the ENTER button.  The screen for entering a password will appear.
5. Press the  S or  T button to select a number from 0 to 9.
6. Press the  X button.
 You can set the next digit.
7. Repeat steps 5 and 6 to set a four-digit password.
8. Enter the password again for confirmation using the same  steps.
9. Select OK, and press the ENTER button.  If the entered passwords don’t match, an error mes-sage will appear.
 To cancel the procedure, select CANCEL, and press  the ENTER button.
 You can cancel the procedure by pressing the MENU  button alternatively.
To cancel the password function: 
1. Display the FEATURE menu. 
2. Press the  S or  T button to select PASSWORD FUNC-
TION. 
3. Press the ENTER button.   The screen for canceling the password function will appear. 
4. Press the ENTER button.   The screen for entering the password will appear. 
5. Press the  S or  T button to select a number from 0. to 9. 
6. Press the  X button. 
 You can set the next digit. 
7. Repeat steps 5 and 6 to enter the four-digit password. 
8. Press the  X button, select OK, and press the ENTER but-
ton. 
 If you enter a wrong password, an error message will  appear.
 To cancel the procedure, press the  X button, select 
CANCEL, and press the ENTER button.
 You can cancel the procedure by pressing the MENU  button alternatively. 
Important: 
 If you forget your password, keep pressing the MENU and 
ENTER buttons on the control panel at the some time about 
three seconds to cancel the password function.
MENU ACCESS
XGA60opt.
LOCK
UNLOCK OK
OK
PASSWORD
CONFIRM
O K CANCEL
MENU ACCESS
XGA60opt.
LOCK
UNLOCK OK
OK
PASSWORD
O K CANCEL 
						

							
EN-22
Lamp replacement
When the lamp no longer functions, replace it with a new one.
Caution:
 Do not remove the lamp immediately after using the projec-tor. You may get burned because the lamp very hot after 
use.
 Before replacing the lamp, press the POWER button to turn  off the lamp and wait for two minutes for lamp to cool down. 
Unplug the power cord from wall outlet and wait one hour 
for the lamp to cool down completely.
 Do not remove the lamp except for replacement. Careless  handling can cause injury or fire.
 Do not touch the lamp direct ly. It may break and cause 
injury or burn.
 Be sure not to drop the lamp lid screw into the projector.  Also be sure not to put metal or any flammable objects 
inside because it may cause fire or electric shock. If any 
objects should fall inside, unplug and contact your dealer.
 Install the lamp securely to prevent failure and fire.
 If the lamp should break, small glass fragments may fall out  through the grilles and some may remain inside of the pro-
jector or the lamp box. When taking the lamp box out, be 
sure to turn over the projector and hold the handle of the 
lamp box to avoid injury due to the glass fragments.
 If the lamp should break, never shake the lamp box or hold  it in front of your face after removing it. The lass fragments 
may fall out and cause injury to your eyes.
 When placing the projector upside down to replace the lamp  or conduct maintenance, ensure that the projector is 
securely placed before working with it.
1. Reverse the projector gently.
2. Loosen the screws (a) using a Phil- lips screwdriver (+), and remove 
the lamp cover (b).
3. Loosen the screws (c) using a Phil- lips screwdriver (+).
4. Pull up the handle.
5. Pull out the lamp box by the handle  while holding the projector.
 Pull the lamp box out of the pro-jector slowly. If it is pulled out 
quickly, the lamp may break 
scattering glass fragments.
 Do not spill liquid on the  removed lamp box or do not 
place it near any flammable 
object or where children can 
reach to prevent injury or fire.
6. Load a new lamp box securely into  the projector in the right orienta-
tion.
7. Put the handle back to the original  position.
 Make sure that the handle is 
locked.
8. Tighten up the screws (c) using a  Phillips screwdriver (+). 9. Tighten up the screw (a) using a 
Phillips screwdriver (+) to secure 
the lamp cover.Reset of the lamp operation time
Plug in the power cord, turn on the 
lamp, and reset the lamp operation time 
by keep pressing the  W, X , and 
POWER buttons on the control panel at 
the same time about three seconds.
Important:
 Unless these three buttons are pressed at the same time,  the lamp operation time isn’t reset.
 Make sure that the STATUS indicator is lit twice and the  lamp operation time  is reset successfully.
 The projector doesn’t turn on if the lamp cover isn’t attached  securely.
 Be sure to reset the lamp operation time whenever you  replace the lamp.
 Do not reset the lamp operation time unless you replace the  lamp.
Caution:
 The lamp is fragile. If it is  broken, be careful not to cut your-
self with glass fragments.
 Contact your dealer for a new lamp.
Interval of lamp replacement
When the lamp shutdown notice is issued, the lamp replace-
ment is recommended even if the lamp is lit normally. 
Decrease in luminescence and/o r color brightness indicates 
that the lamp needs to be repl aced. When the lamp operation 
time exceeds the time elapsed until the lamp shutdown notice
*1 
is issued, the indicator will blink alternately green and red while 
the lamp is lit (while the lamp is not lit, the indicator will blink 
red only) and the lamp replacement message will appear on 
the screen for one minute every time the lamp is turned on. 
When the lamp operation time exceeds the time elapsed until 
the lamp shutdown warning
*2 is issued, the replacement mes-
sage (LAMP EXCHANGE) will appear on the screen for one 
minute at fixed intervals
*4 thereafter.
When the lamp operation time exceeds the time 
elapsed until the lamp shutdown*3, the projector auto-
matically shuts off and can’t be used until the lamp is 
replaced and the lamp operation time is reset.
The times above are when LAMP MODE of the INSTALLATION menu is set to 
LOW. When it is set to STANDARD, this duration will be shortened.
*4These intervals vary depending on the lamp mode setting.
*5When LAMP MODE is set to STANDARD, the time 
elapsed until the lamp shutdown will be shortened to 2000 
hours.
Caution:
 This projector uses a lamp that contains mercury. Disposal 
of the lamp or the projector with the lamp may be regulated 
due to environmental considerations. For disposal or recy-
cling information, please contact  your local authorities or the 
Electronic Industries Alliance: www.eiae.org. (For US only).
(a)
(b)
(c)XD205 U/SD205U
*1 2250 Hours
*2 2850 Hours
*3 3000 Hours*5
(a)
(b) 
						

							
EN-23
ENGLISH
Troubleshooting
The following offers solutions to some of the common problems you may encounter. We suggest that you consult this chart before 
contacting your dealer. 
Images aren’t projected on the screen. 
 
ProblemCause and solution 
Power isn’t turned on.   Check the states of the indicators. 
Images aren’t projected on the screen.  Cancel the AV mute by pressing the MUTE button. 
 Remove the lens cap. 
 The lamp sometimes takes about one minute to light up. 
 On rare occasion, the lamp fails to light up. In such cases, wait a few minutes and try to light the 
lamp again. 
 If the projector was turned off before the lamp cooled down completely, the fans may start rotat- ing and the POWER button may not function when you plug the power cord into the wall outlet 
next time. Wait for the fans to stop and press the POWER button to turn on the lamp again. 
 Check that the lamp cover are closed. 
 Check that the cable connected to the external device isn’t broken. 
 When an extension cord is being used, replace  it with the supplied cable and check whether 
images are projected correctly. If images are proj ected correctly, use an RGB signal amplifier 
along with the extension cord. 
Images suddenly disappear.   The air inlet or outlet grille may be blocked. (In such cases, the STATUS indicator blinks 
orange.) 
JRemove the objects blocking the air inlet or  outlet grille and carry out the following. 
1. Wait for the air inlet or outlet fan to stop (or wait for the STATUS indicator to go out.) 
2. Unplug the power cord from the wall outlet. 
3. Wait about 10 minutes. 
4. Plug the power cord into the wall outlet. 
5. Press the POWER button. 
 When the STATUS indicator is blinking red, it  is indicating that the lamp should be replaced. 
Replace the lamp in this case. 
NO SIGNAL is displayed.   Turn on the power of the connected device, or c
heck whether there is something wrong with the 
connected device. 
 Check whether the external device outputs signal s. (Check this especially when the external 
device is a notebook computer.) 
 Check that the cable connected to the external device isn’t defective. 
 Check that the projector is connected to the ex ternal device using the correct terminals. 
 Check that the connected device is co rrectly selected as the input source. 
 When an extension cord is being used, replace  it with the supplied cable and check whether 
images are projected correctly. If images are proj ected correctly, use an RGB signal amplifier 
along with the extension cord. 
POWER
Off
Steady red
Blinking red  / gr een
STATUS
Off
Off
Blinking  orange
Blinking  green
Steady red Off
Steady or
Blinking
  Solution
If any objects ar e blocking the air inlet or outlet grille, remove them and carry out 
the following.
1. 
2. 
3.  Plug the power cor d into the wall outlet.
4.  Press the POWER button.
Replace the lamp. (The lamp is at the end of its life.)
Attach the lamp cover on the bottom.
Connect the power cord to the projector.  Plug the power cord into a wall outlet. 
Unplug the power cord from the wall outlet.
Make sure that the projector has cooled off. 
If any objects are blocking the air inlet or outlet grille, remove them.\
Dont expose the air outlet grilles to hot air emitted from a heating ap\
pliance.
After the STATUS indicator stops blinking, press the POWER button.
If you unplug the power cord while the fan is rotating, the lamp may not\
 turn on about 
one minute when you plug the power cord next time. 
The lamp cant turn on again for one minute after it goes out. 
Press the POWER button several times.
Unplug the power cord from the wall outlet and contact your dealer. 
						

							
EN-24
Troubleshooting (continued)
Images aren’t projected correctly.
ProblemCause and solution 
Projected images are shaking.
Projected images are displaced.  Check that the cable connected to the external device isn’t intermittent. 
 Connect the cable’s plug with the external device’s connector firmly. 
 Press the AUTO POSITION button. 
 Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu. (See 
page 19.) 
Projected images are distorted.   Adjust the projector and the  screen so that they are perpendicular to each other. (See page 12.) 
Projected images are dark.   Adjust BRIGHTNESS in the IMAGE menu. (See page 18.) 
 Replace the lamp. (See page 22.) 
 Remove the lens cap.
Projected images are blurred.   Adjust the focus. (See page 13.) 
 Clean the lens. 
 Remove the lens cap.
 Press the 
W or  X button on the remote control to eliminate flicker. 
 Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. (See page 18.) 
 Adjust the projector and the screen so that they are perpendicular to each other. (See page 12.)
White dots are seen on projected images.
Black dots are seen on projected images.   This symptom is normal for a DLP projector and is
 not a malfunction. (A very small number of 
pixels may stay lit or out, but such symptom is  not a malfunction. Pixels of 99.99% or more are 
effective.) 
Rainbow blur appears in projected images.  This  is due to color breaking noise that occurs in a DLP system and is not a malfunct ion. 
Fine streak pattern appears in projected 
images.  It occurs because of interference with the 
screen and isn’t a product malfunction. Change the 
screen or readjust the fo cus of the projector.
Projected images (and/or audio) appear wavy 
and distorted.  Connect the cable’s plug with the external device’s connector firmly. 
 Keep the projector away from equipment generating interfering radio waves. 
 When the keystone adjustment is carried ou
t, the image may not be displayed correctly 
because of the type of input signal. This isn’t  a product malfunction. In this case, readjust the 
keystone so that the amount of keystone  correction is as small as possible. 
Tint in projected images is incorrect.  Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 17.) 
 Check that the cable connected to the external device isn’t broken. 
Only the motion areas in the images supplied 
from the computer aren’t displayed.   This is caused by the computer being used. 
Contact the manufacturer of your computer.
Projected images are obscured.  Match the output resolution of your computer with the resolution of the projector.  For the 
method to change the output resolution of the computer, contact the manufacturer of your com-
puter. (See page 29.) 
 Some images and texts appear obscured during t he keystone adjustment. In such cases, use 
the projector without applying the keystone adjustment. (See page 12.) 
						

							
EN-25
ENGLISH
Others
When the problems below occur after the lamp is replaced, check the following.
Maintenance 
Caution: 
Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector . 
Cleaning of the projector and the ventilation slots 
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened 
with diluted mild detergent, and t hen wipe them with a dry cloth. 
To protect the surface of the projector from fading or deteriorating: 
 Do not spray insecticide on or inside the projector. 
 Do not use benzine or thinner to clean it. 
 Do not let rubber or plastic materials contact with projector. 
Cleaning of the lens 
Use a standard lens-cleaning brush or a piece of lens tissue dam pened with lens cleaning fluid. The lens surface is fragile. Use only 
recommended, nonabrasive lens-cleaning materials.  Do not touch the lens with your fingers. 
 
ProblemCause and solution 
Hot air is emitted from the air outlet grilles.  This air comes out as a result of cooling the in
side of the projector. This isn’t a product malfunc-
tion. 
No audio is output.   Check that the volume isn’t set to low. 
The menu can’t be used.   The microcomputers inside the projector ma
y be wrongly operating because of noise. 
J Press the POWER button to turn off the lamp and unplug the power cord from the wall out-
let. Wait about 10 minutes, plug the power cord in, and try again. 
TEMPERATURE!! is displayed.  This indication appears when the ambient temper
ature rises high. When the ambient tempera-
ture stays high, the lamp goes out.
J Eliminate any causes of the rise in the ambient temperature. 
 This indication appears when the air inlet or outlet grille is blocked. When they are kept blocked,  the lamp goes out. 
JRemove the objects blocking the air inlet or outlet grille. 
The   mark appears.  This mark appears when ineffective oper ation is carried out. This isn’t a product malfunction. 
The remote control doesn ’t function easily or 
at all.   Check that the battery is loaded in the remote control or the battery isn’t weak. (See page 8.) 
 Check that the remote control sensor isn’t expos
ed to direct sunlight or fluorescent light. (See 
page 8.) 
 Use the remote control within its operation range. (See page 8.) 
 Use the remote control at least 10 cm away from the projector. 
The buttons on the control panel (except for 
the POWER button) don’t function.  The password function is working. 
JCancel the password lock. (See page 21.)
Abnormal sound is heard.   Because the color wheel spins at a high speed, 
metallic sounds may be heard in rare occa-
sions. Such symptom is not a malfunction. 
ProblemCause and solution 
The power isn’t turned on.   Attach the lamp cover on the bottom correctly. 
 Reset the lamp operation time. (See page 22.) 
The STATUS indicator blinks.   Reset the lamp operation time. (See page 22.)  
						

							
EN-26
Indicators
This projector has two indicators, each of which shows the operation condition of the projector. 
The following offer solutions to possible problems. If these pr oblem persist, turn the projector off and consult your dealer.
Normal condition
Abnormal condition
POWERSTATUSCONDITIONNOTE
Stand-by
Lamp stand-by (about 1 minute) The POWER button cannot be used to switch 
between on and off.
The power is on. (Normal condition)
STATUS indicator POWER indicator
Steady redOff
Steady greenBlinking  green
Steady greenSteady green
POWERSTATUSCONDITIONPOSSIBLE SOLUTION
Abnormal temperature
 The ventilation grilles is clogged with dust or dirt.
 The room temperature is high.  Clean the ventilation grilles.
 Relocate the projector to a cooler place.
The protection circuit is working or the lamp is in an 
abnormal condition.  Wait until the STATUS indicator goes out, 
then press the POWER button.
 If the above solution is not effective,  replace the lamp.
The lamp operation time exc eeds the time elapsed until 
the lamp shutdown notice while the power is on. (See 
page 22.)
Replace the lamp.
Change with a new lamp if this problem 
recurs.
The lamp operation time exc
eeds the time elapsed until 
the lamp shutdown notice while the power is off. (See 
page 22.)
The lamp operation time exc eeds the time elapsed until 
the lamp shutdown. (See page 22.)
The lamp cover isn’t closed. Close the cover correctly.
Abnormal. Contact your dealer.
Steady green
or
Steady red
Blinking orange
Steady redBlinking  green
Steady greenBlinking green/red
Steady redBlinking red
Steady redSteady red
Blinking green/redOff
Blinking green/red
Steadyor
Blinking 
						

							
EN-27
ENGLISH
Specifications
 The specifications and outside appearance of the projector are su bject to change without prior notice. 
Kensington Lock 
This projector has a Kensington Security Standard connector fo r use with Kensington MicroSaver Security System. Refer to the infor-
mation that came with the Kensington System for instructions on  how to use it to secure the projector. Please contact Kensington 
Technology Group below. 
Kensington Technology Group 
2855 Campus Drive 
San Mateo, CA 94403, U.S.A. 
Phone : +1- (650) 572-2700       Fax : +1- (650) 572-9675 
Type DLP™ DATA projector 
Model XD205U/SD205U
Rated power supply 100 - 240 V AC, 50 / 60 Hz 
Rated input 2.9 A (XD205U/SD205U) 
Display Technology 0.55-inch Single chip Digital Micromirro
r Device (DMD) with R,G,B,W color wheel 
Pixels 1024 x 768 = 786432 pixels (XD205 U) 
Pixels 800 x 600 = 480000 pixels (SD205U)
Colors 16770000 colors
Projection lens F 2.4- 2.6 f = 18 - 21.6 mm 
Light source lamp 205 W (XD205U/SD205U) 
Picture size 40 - 300 inch (aspect ratio 4:3) 
PC compatibility Resolution:640x400 (Expand) - 1024x768 (R
eal) - 1280x1024 (Compress) (XD205U) 
Resolution:640x400 (Expand) - 800x600 (R eal) - 1024x768 (Compress) (SD205U) 
Sync on Green available
Video compatibility NTSC / NTSC 4.43 / PAL (including PAL-M, N) / SECAM, PAL-60 
Component Video (DVD/HDTV) (480i, 576i, 480p, 576p, 1080i, 720p)
Speaker 2 W Mono, Round type ø4.5 cm x 1
S-video input Luminance signal: 1.0 Vp-p 75 
Ω (negative sync.) 
Chroma signal: 0.286 Vp-p 75  Ω (burst signal) 
Video input 1.0 Vp-p 75  Ω (negative sync.) 
Audio input 350 mVrms, 10 k Ω or more 
Analog RGB input RGB: 0.7 Vp-p 75 
Ω (negative sync.) 
YP
BPR/YCBCR : Y:1.0 Vp-p (negative sync.) PBPR/CBCR:0.7 Vp-p 
HD/CS : TTL level (positive or negative) 
VD : TTL level (positive or negative)
Control connector USB terminal (for Page Up/Down)
Outside dimensions 261 x 102 x 218 mm (width x height x depth)
Weight Approx.  2.4 kg 
Length of power cord 114 inch (2.9 m)
Temperature, humidity
(performance guaranteed) +41ºF (+5ºC) - +95º
F (+35ºC), 30 - 90%  
						

							
EN-28
Specifications (continued)
Connectors
Dimensional drawings (unit : mm)
What’s included in the box
Replacement part
15
11
6 10
15
pin No.Spec.
1 R(RED)/C
R
2 G(GREEN)/Y
3B(BLUE)/C
B
4GND
5GND
6GND
7GND
8GND
9 DDC5V
10 GND
11 GND
12 DDC Data
13 HD/CS
14 VD
15 DDC Clock
pin No.Spec.
1R(RED)/C
R
2 G(GREEN)/Y
3B(BLUE)/C
B
4-
5GND
6GND
7GND
8GND
9-
10 GND
11 -
12 -
13 HD/CS
14 VD
15 -
COMPUTER IN/OUT (Mini D-SUB 15-pin)
IN OUT
    AC power cord
1  RGB cable for PC
1  VIDEO cable for US
for EU
for UK
246D034-10
246D035-10
246D036-10 (UK only)
246D037-10
246D039-10 1  Remote control
1  Quick Start up
1  Safety manual
1  CD-ROM
1  Carrying case
2  Battery290P131-20
857D082-10
871D472-10
919D273-10
772P046-10
–
(Option / Not included in the box)
Spare lamp (for XD205U/SD205U) 499B045-20 (VLT-XD205LP)
218
102
261 
						

							
EN-29
ENGLISH
Specification of RGB signals in each computer mode of the projector 
Important:
 Some computers aren’t compatible with the projector.
 The projector’s maximum resolution is 1024 x 768 pixels (800 x 600 pixels for SD205U). It may not display images of 
higher resolutions than 1024 x 768 (or 800 x 600) correctly.
 Images with SYNC on G (Green) signal may jitter.
 Images with SYNC on G (Green) signal may be tinged with  green.
 If the resolution and frequency of your computer aren’t  shown on the table, find the compatible resolution and fre-
quency by changing the resolution of your computer.  Set COMPUTER INPUT in the 
SIGNAL menu to RGB when 
inputting the HDTV signal as RGB signal.
 TV60 and TV50 are equivalent to 480i and 576i respec- tively. When these signals are supplied to the VIDEO or S-
VIDEO signal, the signal mode is indicated as TV60 or 
TV50. When they are supplied to the COMPONENT termi-
nal, the signal mode is indicated as 480i or 576i.
Signal moderesolution
(H x V)horizontal
frequency (kHz)vertical
frequency (Hz)XD205U (H x V)SD205U (H x V)
TV60, 480i(525i) - 15.73 59.94 1024 x 768 800 x 600
TV50, 576i(625i) - 15.63 50.00 1024 x 768 800 x 600
1080i 60 (1125i 60) - 33.75 60.00 1024 x 576 800 x 450
1080i 50 (1125i 50) - 28.13 50.00 1024 x 576 800 x 450
480p (525p) - 31.47 59.94 1024 x 768 800 x 600
576p (625p) - 31.25 50.00 1024 x 768 800 x 600
720p 60 (750p 60) - 45.00 60.00 1024 x 576 800 x 450
720p 50 (750p 50) - 37.50 50.00 1024 x 576 800 x 450
PC98 640 x 400 24.82 56.42 1024 x 640 800 x 500
CGA84 640 x 400 37.86 84.13 1024 x 640 800 x 500
CGA85 640 x 400 37.86 85.08 1024 x 640 800 x 500
VGA60 640 x 480 31.47 59.94 1024 x 768 800 x 600
VGA72 640 x 480 37.86 72.81 1024 x 768 800 x 600
VGA75 640 x 480 37.50 75.00 1024 x 768 800 x 600
VGA85 640 x 480 43.27 85.01 1024 x 768 800 x 600
SVGA56 800 x 600 35.16 56.25 1024 x 768 800 x 600
SVGA60 800 x 600 37.88 60.32 1024 x 768 800 x 600
SVGA72 800 x 600 48.08 72.19 1024 x 768 800 x 600
SVGA75 800 x 600 46.88 75.00 1024 x 768 800 x 600
SVGA85 800 x 600 53.67 85.06 1024 x 768 800 x 600
XGA60 1024 x 768 48.36 60.00 1024 x 768 800 x 600
XGA70 1024 x 768 56.48 70.07 1024 x 768 800 x 600
XGA75 1024 x 768 60.02 75.03 1024 x 768 800 x 600
XGA85 1024 x 768 68.68 85.00 1024 x 768 800 x 600
SXGA70a 1152 x 864 63.85 70.01 1024 x 768 -
SXGA75a 1152 x 864 67.50 75.00 1024 x 768 -
SXGA60b 1280 x 960 60.00 60.00 1024 x 768 -
SXGA60 1280 x 1024 63.98 60.02 960 x 768 -
MAC13 640 x 480 35.00 66.67 1024 x 768 800 x 600
MAC16 832 x 624 49.72 74.55 1024 x 768 800 x 600
MAC19 1024 x 768 60.24 75.02 1016 x 768 800 x 600
MAC21 1152 x 870 68.59 74.96 1024 x 768 -
HP75 1024 x 768 62.94 74.92 1024 x 768 800 x 600
SUN66a 1152 x 900 61.85 66.00 984 x 768 -
SUN76a 1152 x 900 71.81 76.64 984 x 768 - 
						

							
MITSUBISHI ELECTRIC CORPORATION
MITSUBISHI Projector Contact Information
North America MESCA (Mitsubishi Electric Sales Canada Inc.)
http://www.mitsubishielectric.ca
Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2, 
Canada
Sales Phone :+1-(905) 475-7728
Fax :+1-(905) 475-7958
E-mail :[email protected] 
Technical Phone :+1-(905) 475-7728
Fax :+1-(905) 475-7958 
Customer Care E-mail :[email protected] 
MDEA (Mitsubishi Digital Electronics America, Inc.)
(Warranty Registration)
http://www.mitsubishi-presentations.com/
Presentation Products Division, 9351 Jeronimo Road, Irvine, CA 92618 U.S.A
Phone Main Line :+1-(949) 465-6000 Technical :+1-(888) 307-0309 
Product Information :+1-(888) 307-0312 
Technical Support 
E-mail :[email protected] 
Europe MEU-FRA (Mitsubishi Electric Europe B.V French Branch) 
25, Boulevard des Bouvets 92 741, Nanterre CEDEX, France 
Sales Phone :+33 (0)1 55-68-55-07Fax :+33 (0)1 55-68-57-31 
Technical  Phone  :+33 (0)1 41-02-83-24 Fax :+33 (0)1 49-01-07-23 
MEU-GER (Mitsubishi Electric Europe B.V. German Branch)
http://www.mitsubishi-evs.de/
Gothaer Strasse 8, 40880 Ratingen, Germany
MEU-IR (Mitsubishi Electric Europe B.V. Irish Branch)
http://www.mitsubishi.ie/
Westgate Business Park, Ballymount, Dublin 24, Ireland
Sales Phone :+353-(0)1- 4198844 Fax :+353-(0)1-4564422 
Technical Phone :+353-(0)1-4198807  Fax :+353-(0)1-4198895 
MEU-IT (Mitsubishi Electric Europe B.V. Italian Branch) 
Centro Direzionale Colleoni, Palazzo Persero-Ingresso 2, Via Paracelso 12, 20041 
Agrate Brianza, Italy 
Sales Phone :+39-(0)39-60531 Fax :+39-(0)39-6053214
E-mail :[email protected] 
MEU-NL (Mitsubishi Electric Europe B.V. Benelux Branch) 
http://www.mitsubishi.nl/LCD/ProdFrame.html 
Nijverheidsweg 23a, 3641 RP Mijdrecht, The Netherlands 
Sales Phone :+31-297-282461 Fax :+31-297-283936 
E-mail :[email protected] 
Technical Phone  :+31-297-282461  Fax :+31-297-283936 
E-mail :[email protected] 
MEU (MITSUBISHI ELECTRIC EUROPE B.V.)
http://www.mitsubishi-projector.ru/
Moscow Representative Office, 12/1 Goncharnaya St. 109240, Moscow, Russia
Sales Phone :+7 (095) 915 8602 Fax :+7 (095) 915 8603 
MEU-SP (Mitsubishi Electric Europe B.V. Spanish Branch)
http://www.mitsubishielectric.es/
Ctra. de Rubi, 76-80, 08190 Sant Cugat del Valles, Barcelona, Spain
Sales Phone  :+34-93.565.31.54 Fax :+34-93.589.43.88 
E-mail :[email protected] 
Technical Phone :+34-93.586.27.51  Fax :+34-93.699.74.45 
E-mail :[email protected] 
MEU-SWE (Mitsubishi Electric Europe B.V Scandinavian Branch) 
Hammarbacken 14, Box 750, S-19127, Sollentuna, Sweden 
Sales Phone  :+46-(0)8-6251070 Fax :+46-(0)8-6251036 
Technical Phone  :+46-(0)8-6251052  Fax :+46-(0)8-6251036 
MEU-UK (Mitsubishi Electric Europe)
http://www.mitsubishi.co.uk/evs/
Visual Information Systems Division, Travellers Lane, Hatfield, Hertfordshire, AL10 
8XB
Sales  Phone  :+44 (1707) 278684 Fax  :+44 (1707) 278541 
E-mail :[email protected] 
Technical  Phone  :+44 (870) 606 5008  Fax  :+44 (1506) 431927 
E-mail :[email protected] 
Russia (Mitsubishi Electric Europe B.V Moscow Representative Office) 
52, bldg.5, Kosmodamianskaya Nab, 113054, Moscow, Russian Federation 
Sales  Phone  :+7 (095) 721 2070  Fax :+7 (095) 721 2071 
Technical  Phone  :+7 (095) 721 2070  Fax  :+7 (095) 721 2071 
AsiaMITSUBISHI ELECTRIC RYODEN AIR-CONDITIONING &
VISUAL INFORMATION SYSTEMS (HONGKONG) LTD.
 Hong Kong Office Units 5-10, 20/F., Ever Gain Plaza, Tower One 88 Container Port Road, Kwai 
Chung, New Territories,Hong Kong. 
Technical  Support 
Phone  :+852 2510 0777
Fax  :+852 2510 0463 
 Beijing Office  9/F, Office Tower 1, Henderson Centre, 18 Jianguomennei Dajie, Dongcheng Dis-
trict, Beijing, 100005, China 
Sales & Technical  Support 
Phone  :+86 (10) 6518 2930 
Fax  :+86 (10) 6518 2530 
 Shanghai Office  10/F, Shanghai Square Office Tower, 138 Huai Hai Zhong Road, Lu Wan District, 
Shanghai, 200021, China 
Sales & Technical  Support 
Phone  :+86 (21) 6327 2228 
Fax  :+86 (21) 6327 4918 
 Shenzhen Office  Unit 01-04, 13/F, Building A, Tian An International Building, Renmin Road South, 
Shenzhen, 518005, China 
Sales & Technical  Support 
Phone  :+86 (755) 518 6386 
Fax  :+86 (755) 218 4775 
 Chengdu Office  Block B-1, 23/F., Chuan Xin Mansion, 18 Section 2, Renmin Road South, Chengdu, 
610016, China 
Sales & Technical  Support 
Phone  :+86 (28) 619 9730 
Fax  :+86 (28) 619 9801 
MEAP (Mitsubishi Electric Asia Pte Ltd) 
http://www.mitsubishielectric.com.sg 
307 Alexandra Road, Mitsubishi Electric Building, 289245,Singapore 
Main Line  Phone  :+65 6 473 2308  Fax  :+65 6 475 9503 
Sales & Technical Support  E-mail :[email protected] 
AMS (Antah Melco Sales & Services Sdn Bhd (A Joint-Venture Company of Mitsubishi 
Electric Corporation)) 
http://www.antahmelco.com.
my 6, Jalan 13/6, Petaling Jaya, Selangor Darul Ehsan, Malaysia 
Main Line  Phone :+603-7955 2088 Fax :+603-7956 3950 
:+603-7958 2576 
Technical Support  Phone :+603-7955 2088 
E-mail :[email protected] 
Product Information  Phone :+603-7955 2088
 
ME-TWN (Mitsubishi Electric Taiwan Co., Ltd.) 
http://www.mitsubishi-electric.com.
tw 9th Floor., 90 Sec. 6, Chung Shan N. Rd., Taipei, Taiwan 
Sales Support
  Phone  : +886 (0) 2 2832 8255  Fax  : +886 (0) 2 2833 9813 
KYW (Kang Yong Watana Co., Ltd.)
http://www.mitsubishi-kyw.in.th 
28 Krungthep Kreetha Road, Huamark Bangkapi, Bangkok, 10240, Thailand 
Sales Support Phone  :+66 (2) 731 6901 
Fax  :+66 (2) 379 4763 
STC (Setsuyo Astec Corp. Seoul Branch)
Dongseo Game Channel Bldg, 660-11, Deungchon-dong, Kangseo-ku, Seoul, Korea
Main Line Phone  :+82 (0) 2 3665 4964 Fax  :+82 (0) 2 3665 4965 
Oceania ME-AUST (Mitsubishi Electric Australia) 
http://www.mitsubishi-electric.com.au/prod.asp?prod=proj 
348 Victoria Road, Rydalmere, N.S.W. 2116, Australia 
Sales Phone  :+(612)9684-7777
Fax :+(612)9898-0484
E-mail :[email protected]
BDT (Black Diamond Technologies Ltd.) 
(Warranty Registration)  
http://www.bdt.co.nz/projectors/warranty.asp 
1 Parliament St, Lower Hutt, Wellington, New Zealand 
Sales Phone  :+64-(0)4-560-9100 Fax :+64-(0)4-560-9133 
E-mail :[email protected]
Technical Phone  :+64-(0)4-560-9100  Fax :+64-(0)4-560-9133  
Manufactured by Mitsubishi Electric Corporation 
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan