Mitsubishi Hc2000 Projector User Manual
Here you can view all the pages of manual Mitsubishi Hc2000 Projector User Manual. The Mitsubishi manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 11
EN-11 ENGLISH Setting up your projector A=B # LAMP AC IN MAIN TEMP POWER Setting up the screen Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the projection angle of the projector. (See below.) •Install the screen and projector so that the projector’s lens is placed at the same height and horizontal position of the screen center. •Do not install the screen where it is exposed to direct sunlight or lighting. Light directly reflecting on the...
Page 12
EN-12 50 127 24 62 44 111 69 175 93 23660 152 30 75 52 133 83 210 111 283 70 178 34 87 61 155 96 245 130 331 80 203 39 100 70 177 110 280 149 37890 229 44 112 78 199 124 315 167 425 100 254 49 125 87 221 138 350 186 472 110 279 54137 96 244 152 385 205 520120 305 59 149 105 266 165 420 223 567 130 330 64 162 113 288 179 455 242 614 140 356 69 174 122 310 193 490 260 661150 381 74 187 131 332 207 525 279 709 200 508 98 249 174 443 276 700 372 945 2506351223112185533448754651181 Setting up your projector...
Page 13
EN-13 ENGLISH When the aspect ratio of the screen is 4:3: When the aspect ratio of the screen is 4:3, the positional relation between the projected image and the screen is as shown on the right. Refer to the following table for installation. To position the projector relative to the screen: To position the screen relative to the projector: Screen size Size of the projected image Blank Projected distance (L) 4:3DiagonalHeight C Width B Height A Width Bspace (D)Min. Max. inch cm inch cm inch cm inch cm...
Page 14
EN-14 S-VIDEO RS-232C Y G(Y)Cb/Pb Cr/Pr VIDEODV I B(Cb/Pb) R(Cr/Pr) H/HV V S-VIDEO RS-232C Y G(Y)Cb/Pb Cr/Pr VIDEODV I B(Cb/Pb) R(Cr/Pr) H/HV V CB(PB)Y CR(PR) B G R B(Cb/Pb) G(Y) R(Cr/Pr) C B(PB) Y CR(PR) Cb/Pb Y Cr/Pr Viewing video images S-VIDEO RS-232C Cb/Pb Cr/Pr VIDEODV I B(Cb/Pb) R(Cr/Pr) H/HV V 1 2 S-VIDEO RS-232C PbCr/PrVIDEO DV Ib/Pb) R(Cr/Pr) H/HV V 1 2 A. Connecting the projector to video equipment Preparations: •Make sure that the power of the projector and that of the video equipment...
Page 15
EN-15 ENGLISH Connecting to video equipment having a DVI-D terminal You can project high-quality images by connecting the DVI terminal of this projector to video equipment having a DVI-D output terminal. In addition, this projector supports HDCP and is able to receive encrypted digital video data that are output from DVD players. •For connection to the DVI terminal, use a commercially available DVI cable. •Select DVI-DIGITAL as the input source. •Only RGB signals are supported. Component video signals...
Page 16
EN-16 Viewing video images (continued) C. Projectiing images Preparation: •Remove the lens cap. •Turn on the power of the connected video equipment. 1. Turn the main power switch to on (or to the I position). •When the main power switch is turned on, the POWER indicator lights up red. •If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the main power switch is turned on. (The POWER indicator blinks...
Page 17
EN-17 ENGLISH AU TO MENU DVI-DCOMP BNC ZOOM MEM3 S-Video OFF Video DVI-A 16:9 MEM2 ENTER FOCUS–/LEFT FOCUS+/RIGHTZOOM IN/UP ZOOM OUT/DOWN LIGHT Standard MEM1 CONTBRIGHTC.TEMP TINTCOLORSHARP LAMP AC IN MAIN TEMP POWER ONSTANDBY INSTALLATION TEST PATTERN SIGNAL SETTING COMPONENT FLOOR FRONTSTANDARD 0 ENGLISHAUTO ASPECT MIRROR KEYSTONE LANGUAGE EXPAND opt. KEYSTONE H.KEYSTONE0 0 V.KETSTONE To stop projecting: 9. Press the POWER button on the projector or the OFF button on the remote control. •A confirmation...
Page 18
EN-18 AUTO D V I-DCOMP BNC ZOOM MEM3 S -V id e o OFF ON Video DV I - A 16:9 MEM2 ZOOM IN/UP LIGHT S ta n d a rd M E M 1 STANDBY INSTALLATION TEST PATTERN SIGNAL SETTING COMPONENT FLOOR FRONTSTANDARD 0 ENGLISHAUTO ASPECT MIRROR KEYSTONE LANGUAGE EXPAND opt. Viewing video images (continued) Setting the aspect ratio You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting according to the type of the input video signal. How to change the...
Page 19
EN-19 ENGLISH S-VIDEO RS-232C Pb Cr/Pr VIDEODV I b/Pb) R(Cr/Pr) H/HV V 2 1 S-VIDEO RS-232C bCr/PrVIDEO DV I Pb) R(Cr/Pr) H/HV V 2 1 S-VIDEO RS-232C Y G(Y)Cb/Pb Cr/Pr VIDEODV I B(Cb/Pb) R(Cr/Pr) H/HV V DV I - I2 1 Viewing computer images A. Connecting the projector to a computer Preparation: •Make sure that the power of the projector and that of the computer are turned off. •When connecting the projector to a desktop computer, disconnect the RGB cables that are connected to the monitor. For analog...
Page 20
EN-20 Viewing video images (continued) AUTO MENU DVI-DCOMP BNC ZOOM MEM3 S-Video OFF Video DVI-A 16:9 MEM2 ENTER FOCUS–/LEFT FOCUS+/RIGHTZOOM IN/UP ZOOM OUT/DOWN LIGHT Standard MEM1 CONTBRIGHTC.TEMP TINTCOLORSHARP LAMP AC IN MAIN TEMP POWER AUTO POSITION SOURCE MENU/EXIT ENTERZOOM OUT / DOWNZOOM IN / UP FOCUS +/RIGHT FOCUS -/LEFTAUTO POSITION SOURCE MENU/EXIT ENTERZOOM OUT / DOWNZOOM IN / UPLENS SHIFT DOWN UP FOCUS +/RIGHT FOCUS -/LEFT ONSTANDBY C. Projectiing images Preparation: •Remove the lens cap....