Mitsubishi Electric CP9810DW User Manual
Have a look at the manual Mitsubishi Electric CP9810DW User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 561 Mitsubishi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
8 CONNECTIONS OTHERS PRECAUTIONS FEATURES PREPARATIONTROUBLE- SHOOTING CONTENTS 4 5 2 1 3 3 1 11 1 1USB TERMINAL Use to connect the USB cable. See page 9. 2 22 2 2DIP SWITCHES Use to set various functions of this unit. See page 10. SIDE AND REAR PANEL FEATURES AND FUNCTIONS 3 33 3 3HANDLE FOR TRANSPORTING When transporting this unit, hold this handle and the upper front part of this unit. 4 44 4 4POWER SOCKET (AC LINE) Use to connect the provided power cord. Insert the cord firmly. 5 55 5 5POWER SWITCH Use to switch the power ON and OFF. (LEFT SIDE) (REAR) INSTALLING THE PAPER CATCHER Hook the paper catcher by its latches. When using the print paper of 13x18(5x7”), 15x20(6x8”) or 15x23(6x9”), do not install the paper catcher. A. B. C. Holes for 10 x 15 size paper (Paper width: 152 mm) Holes for 9 x 13 size paper (Paper width: 127 mm) foot screw INSTALLATION Place the printer on a stable table. Make sure that the bottom of the door does not touch the table when opened and that the printer does not fall from the table. Place the printer so that the door does not touch the corner of the table. REMOVING THE FEET 1. Remove the paper strip bin. 2. Place the printer sideways as shown in the figure. NOTE Be careful not to get your fingers pinched. 3. Loosen 4 screws to remove the feet. 4. Raise the printer. Keep the removed screws and feet. Downloaded From ManualsPrinter.com Manuals
9 CONNECTIONS OTHERS PRECAUTIONS FEATURES PREPARATIONTROUBLE- SHOOTING CONTENTS CONNECTIONS CONNECTION WITH USB DATA SIGNAL EQUIPMENT To USB port Personal computer Digital color printer To USB port 2 22 2 2CONNECTING TO PERSONAL COMPUTER (EXAMPLE) Connect this unit to a personal computer as shown below. NOTE A USB cable is not supplied with this unit. Use the USB 2.0 certified cable of 2 m or less in length. Downloaded From ManualsPrinter.com Manuals
10 CONNECTIONS OTHERS PRECAUTIONS FEATURES PREPARATIONTROUBLE- SHOOTING CONTENTS SETTING OF DIP SWITCHES 2 22 2 2SETTING DIP SWITCHES All the switches are set to OFF at the time of shipment from the factory. Turn off the power before changing the DIP switch settings. Switch No.Setting Function 1OFF Auto feed & cut mode When the door is closed after the print paper is installed with this unit powered on, this unit automatically carries out paper feed & cut operation. ON Manual feed & cut mode 2OFF Set this switch to OFF. ON 3OFF Set this switch to OFF. ON 4OFF Set this switch to OFF. ON 5OFF Set this switch to OFF. ON 6OFF Set this switch to OFF. ON 7OFF Set this switch to OFF. ON 8OFF Set this switch to OFF. ON CONNECTIONS Downloaded From ManualsPrinter.com Manuals
11 CONNECTIONS OTHERS PRECAUTIONS FEATURES PREPARATIONTROUBLE- SHOOTING CONTENTS BEFORE OPERATION Before printing, 1 11 1 1 Install the print paper to this unit. (See below.) 2 22 2 2 Position the adjustable paper guides. (See page 13.) 3 33 3 3 Install the ink ribbon to this unit. (See page 14-15.) INSTALLATION OF PRINT PAPER Spacers 2For the usage of the spacers, see the Quick Setup Guide. Remove the cushions put between the paper flange and spacer when using the spacers. How to attach the spacers 1. Attach the spacer with the paper flange’s stoppers retracted. 2. Turn the spacer until the latches are locked. When you remove the spacers from the paper flanges, follow the above procedure in reverse. Spacer LatchPaper flange 1 11 1 1Attach the supplied paper flanges to both sides of the print paper. When you pinch the latches on the paper flange, the stoppers retract into the shaft. Attach the flanges to the print paper with the stoppers retracted. Make sure that the flanges are attached to the print paper securely, and release the latches. NOTE •Take care not to pinch your fingers. •Do not remove the sticker on the print paper yet. •Do not slacken the paper. Any slack in the print paper may degrade the print quality. CAUTION •When placing the print paper, remove one flange and keep the print paper upright on its side with no flange. •When you put the print paper sideways, it may roll and fall. This may cause injury. NOTE •Do not touch the thermal head. Fingerprints or dust on the thermal head will degrade the print quality. •Fingerprints or dust on the paper’s surface may degrade print quality and cause paper jams.Sticker INCORRECT CORRECT Downloaded From ManualsPrinter.com Manuals
12 CONNECTIONS OTHERS PRECAUTIONS FEATURES PREPARATIONTROUBLE- SHOOTING CONTENTS 4 44 4 4Install the print paper into the unit. Make sure to install the print paper firmly. NOTE Install the print paper into the unit slowly. If it is dropped along the ditches, the unit or accessories may be damaged. RollerPrint paper 5 55 5 5Remove the sticker, insert the print paper between the rollers as shown right, and feed the print paper until it reaches the black cover. •Remove the sticker before inserting the print paper between rollers. Make sure to insert the paper straight. NOTE •Keep the roller clean. Dirt on the roller may degrade the print quality. NOTE •When taking the print paper out, pull it up toward you. •Make sure to turn on the power before replacing the print paper. •Make sure to eliminate any slack from the print paper. If you carry out the following steps without eliminating the slack, the print paper may be damaged.Black cover 2 22 2 2Press the POWER switch on the rear panel to turn on the power. 3 33 3 3After the mechanical initialization is completed, press the DOOR OPEN button to open the door. Take the ink cassette in the printer out. Direction of paper insertion BEFORE OPERATION CAUTION •Do not touch the thermal head right after printing because it is extremely hot. Otherwise you may get burned or injured. NOTE •Note that the thermal head is quite sensitive to static electricity. When you touch the thermal head while carrying static electricity on your body, the thermal head may be damaged.Thermal head (inside) POWER switch Downloaded From ManualsPrinter.com Manuals
13 CONNECTIONS OTHERS PRECAUTIONS FEATURES PREPARATIONTROUBLE- SHOOTING CONTENTS BEFORE OPERATION POSITIONING OF ADJUSTABLE PAPER GUIDE Adjust the paper guides according to the size of print paper to be used.Adjustable paper guides Fixed rollers 2 22 2 2HOW TO SHIFT THE ADJUSTABLE PAPER GUIDES 1 11 1 1Push both the adjustable paper guides with both hands until they touch the fixed rollers respectively. 2 22 2 2Turn each paper guide in the direction of the arrows until they stop. For 9x13(3x5”) or 13x18(5x7”) size paper (5”-width)For 10x15(4x6”), 15x20(6x8”) or 15x23(6x9”) size paper (6”-width) 3 33 3 3When you release the paper guides, they are fixed to the appropriate width depending on the size of the paper to be used. NOTE •Make sure to adjust the adjustable paper guides according to the size of print paper to be used. When they are not positioned properly, a malfunction such as paper jam and misaligned printing position may occur. For 9x13(3x5”) or 13x18(5x7”) size paper (5”-width)For 10x15(4x6”), 15x20(6x8”) or 15x23(6x9”) size paper (6”-width) Downloaded From ManualsPrinter.com Manuals
14 CONNECTIONS OTHERS PRECAUTIONS FEATURES PREPARATIONTROUBLE- SHOOTING CONTENTS BEFORE OPERATION INSTALLATION OF INK RIBBON 2 22 2 2 INSTALLING THE INK CASSETTE 1 11 1 1Place the ink cassette containing the ink ribbon in the position as shown right. Place the ink cassette on the print paper with the shaft (thicker one) around which the ink ribbon is wound located to the front. Align the arrows marked on the sides of ink cassette with those on the unit. Place the rear of the ink cassette along the guides that are provided inside the unit. Guides Arrows 2 22 2 2INSTALLING THE INK RIBBON After installing the print paper, install the ink cassette into this unit. Before installing the ink cassette into this unit, load the ink ribbon in the ink cassette. NOTE •Place the ink cassette on a flat surface, when loading the ink ribbon. •Select a place that is free of dust when loading the ink ribbon. Dust or dirt settling on the ink ribbon results in poor print quality. •Make sure that the shafts of the ink ribbon fit into the ink cassette firmly. NOTE •Make sure to use the black ink cassette supplied with the printer. The ink cassettes for the CP9000, CP9500 and CP9550 series cannot be used. 1 11 1 1Load the ink ribbon in the ink cassette as shown below. •Make sure to load it in the correct position. First, tilt the ink ribbon and insert the gear 1 in the ditch 1 of the ink cassette, and then push the gear 2 into the ditch 2 by rotating the ink ribbon. Similarly, insert the gear 3 in the ditch 3 and then push the gear 4 into the ditch 4. Make sure to set the ink ribbon roller to the ditches firmly. Turn the ivory gear to eliminate any slack. 43 2 4 3 112 34 12 Ink ribbon Gear (ivory) Ink cassetteHandle Ditch Downloaded From ManualsPrinter.com Manuals
15 CONNECTIONS OTHERS PRECAUTIONS FEATURES PREPARATIONTROUBLE- SHOOTING CONTENTS 2 22 2 2Push the ink cassette toward the back of the unit. Hold the handle of the ink cassette and push it straight toward the back of the unit. Then raise it until you hear a click to secure it in the ink cassette holder. NOTE If the ink ribbon is used up, repeat the steps 1 to 2 to replace the print paper and the ink ribbon. CANCEL FEED&CUT 3 33 3 3Push the center of the door to close. The print paper setting is initialized two seconds after you close the door. When the auto feed & cut mode has been selected, the FEED & CUT procedure is repeated three times after you close the door. When the print paper with the post card printing on its reverse side is installed, the FEED & CUT procedure is repeated five times. NOTE •When closing the door, push it until a click is heard. •If the PAPER/INK RIBBON indicator illuminates when the door is closed, the print paper may have not been installed correctly. In this case, open the door to make sure that the print paper has been installed correctly. Then close the door again. •On the auto feed & cut mode, when the print paper is installed more than three times, the print paper may be used up earlier than the ink ribbon. 2 22 2 2 When the manual & cut mode has been selected When the manual feed & cut mode has been selected, hold down the FEED & CUT button for 1 second or longer. Repeat the manual feed & cut three times. When the print paper with the post card printing on its reverse side is installed, repeat this procedure five times. For how to select the auto feed & cut mode, see Setting of DIP switches (on page 10). Installation of the print paper and the ink ribbon is completed. NOTE •Make sure to replace the print paper and the ink ribbon at the same time. •When replacing them, throw away the paper chips in the paper strip bin. •Whenever you replace the print paper and the ink ribbon, clean the thermal head and the roller. For the cleaning procedures, see “CLEANING” (on pages 21 and 22). BEFORE OPERATION Thermal head (inside) Downloaded From ManualsPrinter.com Manuals
16 CONNECTIONS OTHERS PRECAUTIONS FEATURES PREPARATIONTROUBLE- SHOOTING CONTENTS BEFORE OPERATION HANDLING OF PAPER / INK RIBBON SET 2 22 2 2 BEFORE PRINTING •Fingerprints or dust on the paper’s printing surface may degrade the print quality and cause paper jams. When the manual feed & cut mode has been selected, repeat the FEED & CUT procedure three times after replacing the print paper. When the print paper with the post card printing on its reverse side is installed, repeat five times. If you omit cutting the print paper by the FEED & CUT procedure, first two or three prints may not be printed partly because of finger oil or dirt. •When the print paper or ink ribbon is abruptly transferred from a cool place to a hot place, vapor or dew is generated on the surface, which causes paper jams or degraded print quality. Leave the print paper in the room to stabilize its temperature before use. •If you repeat the FEED & CUT procedure more than the designated number of times while installing the print paper, the indicated number of prints may not be made. In addition, if you replace the print paper before it is used up, the indicated number of prints may not be made. 2 22 2 2 AFTER PRINTING •If the paper absorbs nonvolatile organic solvents (alcohol, ester, ketone, etc.) the print may be discolored. •Discoloration of prints is accelerated if the print paper comes into contact with soft vinyl chloride such as transparent tape. •Avoid storing prints in direct sunlight or places with high humidity. 2 22 2 2 STORAGE OF PAPER / INK RIBBON SET •Do not store the print paper and ink ribbon in the container made of soft polyvinyl chloride. They may be discolored because of chemical reaction. •Store the print paper and ink ribbon out of direct sunlight and away from heating appliances in a cool, dark place where the temperature is 5˚C to 30˚C and the humidity is 20% to 60% RH. Downloaded From ManualsPrinter.com Manuals
17 CONNECTIONS OTHERS PRECAUTIONS FEATURES PREPARATIONTROUBLE- SHOOTING CONTENTS INSTALLATION OF PRINTER DRIVER 2The printer driver is required to print the data from the personal computer connected with this unit. The printer driver for Windows ® is supplied with this unit. 2Refer to the PRINTER DRIVER GUIDE in the CD-ROM for installing the printer driver. Microsoft, Windows, Windows 2000, Windows XP and Windows Vista are the registered trademarks of Microsoft Corporation in the U.S.A. and other countries. Product nameRequired operating system CPD9810X Applies for Microsoft® Windows® 2000 or Windows® XP operation system BEFORE OPERATION CPD9810V Applies for Windows Vista® operation system Downloaded From ManualsPrinter.com Manuals