Minolta PagePro 1200W User Manual
Have a look at the manual Minolta PagePro 1200W User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 7 Minolta manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Appendix10 10-7 Do not use flammable sprays, liquids, or gases near this product, as a fire could result. Do not leave a toner unit or drum unit in a place within easy reach of children. Licking or ingesting any of these things could injure your health. Do not let any object plug the ventilation holes of this product. Heat could accumulate inside the product, resulting in a fire or malfunction. Do not install this product at a site that is exposed to direct sunlight, or near an air conditioner or heating apparatus. The resultant temperature changes inside the product could cause a malfunction, fire, or electrical shock. Do not place the product in a dusty place, or a site exposed to soot or steam, near a kitchen table, bath, or a humidifier. A fire, electrical shock, or breakdown could result. Do not place this product on an unstable or tilted bench, or in a location subject to a lot of vibration and shock. It could drop or fall, causing personal injury or mechanical breakdown. After installing this product, mount it on a secure base. If the unit moves or falls, it may cause personal injury. Do not store toner units and PC drum units near a floppy disk or watch that are susceptible to magnetism. They could cause these products to malfunction. Do not place any objects around the power plug as the power plug may be difficult to pull out when an emergency occurs. Do not touch the electrical contacts that are located inside the top cover and underneath the cartridge as an electrostatic discharge may damage the printer. The inside of this product has areas subject to high temperature, which may cause burns. When checking the inside of the unit for malfunctions such as a paper misfeed, do not touch the locations (around the fusing unit, etc.) which are indicated by a “Caution! High Temperature!” warning label. The socket-outlet shall be installed near the machine and shall be easily accessible as the power plug may be difficult to pull out when an emergency occurs. Always use this product in a well ventilated location. Operating the product in a poorly ventilated room for an extended period of time could injure your health. Ventilate the room at regular intervals. Whenever moving this product, be sure to disconnect the power cord and other cables. Failure to do this could damage the cord or cable, resulting in a fire, electrical shock, or breakdown. When moving this product, always hold it by the locations specified in the user manual or other documents. If the unit falls it may cause severe personal injury. The product may also be damaged or malfunction. Remove the power plug from the outlet more than one time a year and clean the area between the plug terminals. Dust that accumulates between the plug terminals may cause a fire. When unplugging the power cord, be sure to hold onto the plug. Pulling on the power cord could damage the cord, resulting in a fire or electrical shock. Downloaded From ManualsPrinter.com Manuals
10Appendix 10-8 10.8 Working safely with your laser printer Notes on your safety and operating safety Working improperly with the printer can result in health hazards, electric shocks and even fires. Before you unpack the laser printer, you should make yourself familiar with this information on your safety and operating safety. CAUTION Observe the following information: ➜Make sure that the power cord is correctly plugged into the socket and that the socket is at all times visible and readily accessible. ➜Do not pull on the cord to pull the power plug out of the socket as this may damage the cord. The result could be an electric shock or a fire. ➜Remove the power plug from the socket if the machine will not be in use for an extended period of time. ➜Do not remove the power cord from the socket with wet hands as this may result in an electric shock. ➜Do not move the unit unless the power cord has been removed from the socket. Otherwise you may damage the cord. The result could be a short-circuit or a fire. ➜Do not place any heavy objects on the power cord. Do not pull or kink the cord as this can result in damage to the cord. The result could be an electric shock or a fire. ➜Make sure that the machine is not standing on a cord to another machine as this can result in damage to that cord. The result could be a fire or improper functioning of the unit in question. ➜Make sure that the power supply to the unit has the correct voltage. Otherwise the result could be a fire or an electric shock. ➜Switch off the unit immediately and unplug the power cord if the power supply cord is damaged. Failure to do so could result in a fire or an electric shock. Inform your customer support technical specialist. ➜Use only extension cords that are designed for at least the maximum power rating of the machine. Extension cords with lower ratings can result in the unit overheating and can even lead to a fire. ➜Perform only the procedures that are described in this manual. Using the machine improperly can result in a fire or an electric shock. Downloaded From ManualsPrinter.com Manuals
Appendix10 10-9 ➜Do not place any heavy objects on the machine. ➜Do not open any covers on the machine while printing is in progress. ➜Do not switch off the unit while printing is in progress. ➜Do not place any magnetic objects near the machine. ➜Do not use any flammable sprays, liquids or gases in the vicinity of the machine. ➜Do not remove any safety devices and do not alter the construction of the machine. The unit is equipped with high-voltage components. Using the machine improperly can result in a fire or an electric shock. ➜Do not insert any paper clips, staples or other small metal objects into openings on the machine. The result could be an electric shock or a fire. If metal pieces are fed into the machine, switch it off immediately, disconnect the power cord and inform your customer support technical specialist. ➜Do not place coffee cups, drink bottles, or other containers with liquids in them on the machine. If liquid enters the machine, the result could be an electric shock or a fire. If liquid does get into the machine, switch it off immediately, disconnect the power cord and inform your customer support technical specialist. ➜If the machine becomes unusually hot, or if you notice smoke or an unusual odor coming from the machine, switch it off immediately and remove the power cord from the socket. Inform your customer support technical specialist. Downloaded From ManualsPrinter.com Manuals
10Appendix 10-10Laser safety This is a page printer which operates by means of a laser. There is no pos- sibility of danger from the laser, provided the printer is operated according to the instructions in this manual. Since radiation emitted by the laser is completely confined within protec- tive housing, the laser beam cannot escape from the machine during any phase of user operation. Internal laser radiation Maximum average radiation power: 27 µ W at the laser aperture of the print head unit. Wavelength: 770-810 nm This product employs a Class 3b laser diode that emits an invisible laser beam. The laser diode and the scanning polygon mirror are incorporated in the print head unit. The print head unit is NOT A FIELD SERVICEABLE ITEM. Therefore, the print head unit should not be opened under any circum- stances. Laser caution label A laser caution label is attached inside the machine as shown below. Do not dispose of the printer or consumables other than being directed in the manual. This product has a laser beam source inside that could cause blindness if the safeguard is damaged. The above figure shows the internal view of the printer when the top cover is open. Laser aperture of the print head unit Downloaded From ManualsPrinter.com Manuals
Appendix10 10-11 Laser safety label A laser safety label is attached to the outside of the machine as shown be- low. For United States users CDRH Regulations This machine is certified as a Class 1 Laser product under the Radiation Performance Standard according to the Food, Drug and Cosmetic Act of 1990. Compliance is mandatory for Laser products marketed in the United States and is reported to the Center for Devices and Radiological Health (CDRH) of the US Food and Drug Administration of the US Department of Health and Human Services (DHHS). This means that this device does not produce hazardous laser radiation. The label shown above indicates compliance with the CDRH regulations and must be attached to laser products marketed in the United States. CAUTION Use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. This is a semiconductor laser. The maximum power of the laser diode is 5 mW and the wavelength is 770-810 nm. Downloaded From ManualsPrinter.com Manuals
10Appendix 10-12For users in all countries CAUTION Use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. This machine is certified as a Class 1 laser product. This means that the machine does not produce hazardous laser radiation. This is a semiconductor laser. The maximum power of the laser diode is 5 mW and the wavelength is 770-810 nm. For Denmark users ADVARSEL Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funk- tion. Undgå udsættelse for stråling. Klasse 1 laser produkt der opfylder IEC60825 sikkerheds kravene. Dansk: Dette er en halvlederlaser. Laserdiodens højeste styrke er 5 mW og bølgelængden er 770-810 nm. For Norway users ADVERSEL Dersom apparatet brukes på annen måte enn spesifisert i denne bruksan- visning, kan brukeren utsettes for unsynlig laserstråling som overskrider grensen for laser klass 1. Dette en halvleder laser. Maksimal effekt till laserdiode er 5 mW og bølge- lengde er 770-810 nm. For Finland, Sweden ssers LOUKAN 1 LASERLAITE KLASS 1 LASER APPARAT VAROITUS! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle. Tämä on puolijohdelaser. Laserdiodin suurin teho on 5 mW ja aallonpituus on 770 – 810 nm. Downloaded From ManualsPrinter.com Manuals
Appendix10 10-13 VARNING! Om apparaten används på annat sätt än i denna bruksanvisning specifi- cerats, kan användaren utsättas för osynlig laserstrålning, som överskrid- er gränsen för laserklass 1. Det här är en halvledarlaser. Den maximala effekten för laserdioden är 5 mW och våglängden är 770 – 810 nm. VARO! Avattaessa ja suojalukitus ohitettaessa oletPP alttiina näkymättömälle la- sersäteilylle. Älä katso säteeseen. VARNING! Osynlig laserstrålning när denna del är öppnad och spärren är urkopplad. Betrakta ej strålen. Ozone release During printer operation, a small quantity of ozone is released. This amount is not large enough to harm anyone adversely. However, be sure the room where the machine is being used has adequate ventilation, es- pecially if you are printing a high volume of materials, or if the machine is being used continuously over a long period. Dégagement d’ozone L’imprimante dégage une faible quantité d’ozone durant son utilisation. Cette quantité n’est pas suffisamment importante pour être dangereuse. Cependant, veillez à ce que la pièce dans laquelle la machine soit adéquatement ventilée, surtout en cas d’impression de gros volumes ou en cas d’utilisation continue pendant un laps de temps très long. Downloaded From ManualsPrinter.com Manuals
Index11 11-1 11 Index A Accessories see Optional accessories ............................................................... 7-1 Add Printer ........................................................................................... 3-2 B Button see Panel button ............................................................................ 6-4 C Cleaning the printer ........................................................................... 8-10 paper feed roller ........................................................................... 8-11 Connecting the printer ....................................................................... 2-12 Consumables storage ........................................................................................... 2-5 Control panel button see Panel button ............................................................................ 6-4 Control panel indicators Error ............................................................................................... 6-4 Ready ............................................................................................. 6-4 E Envelopes ............................................................................................ 6-1 Error indicator ...................................................................................... 6-4 Error messages ................................................................................. 9-12 F Face-down output ................................................................................ 6-7 Face-down tray ............................................................................ 2-1, 6-7 Face-up output .................................................................................... 6-7 Face-up tray ........................................................................................ 6-7 Downloaded From ManualsPrinter.com Manuals
11Index 11-2 I Installing ............................................................................................ 3-21 Installing the printer ............................................................................. 2-5 J Jam see Media jam ............................................................................... 9-7 L Loading envelopes .............................................................................. 6-1 Loading paper ..................................................................................... 6-1 lower feeder unit ............................................................................ 6-6 manual feed tray .....................................................................2-8, 6-6 Tray 1 .....................................................................................2-7, 6-5 Tray 2 ............................................................................................ 6-6 M Maintenance ....................................................................................... 8-1 Media jam inside of the printer ........................................................................ 9-1 lower feeder unit ............................................................................ 9-7 manual feed tray ............................................................................ 9-6 output tray ..................................................................................... 9-4 Media type list ..................................................................................... 6-3 Messages error messages ........................................................................... 9-12 service ......................................................................................... 9-13 status ........................................................................................... 9-12 O Optional accessories face-up tray ................................................................................... 7-3 Lower feeder unit ........................................................................... 7-1 storage .......................................................................................... 2-5 Output face-down ...................................................................................... 6-7 face-up .......................................................................................... 6-7 Overview of printer .............................................................................. 2-1 control panel .................................................................................. 2-4 Downloaded From ManualsPrinter.com Manuals