Home > MikroTik > Router > MikroTik Router OS V3.0 User Manual

MikroTik Router OS V3.0 User Manual

Here you can view all the pages of manual MikroTik Router OS V3.0 User Manual. The MikroTik manuals for Router are available online for free. You can easily download all the documents as PDF.

Page 481

watch-address. The default setting means that if watch-address is set and is not reachable, the router
will reboot about every 6 minutes.
send-email-from(text; default:) - e-mail address to send the support output file from. If not set,
the value set in /tool e-mail is used
send-email-to(text; default:) - e-mail address to send the support output file to
send-smtp-server(text; default:) - SMTP server address to send the support output file through.
If not set, the value set in /tool e-mail is used...

Page 482

UPS Monitor
Document revision 2.3 (February 6, 2008, 4:08 GMT)
This document applies to MikroTik RouterOS V3.0
Table of Contents
TableofContents
Summary
Specifications
Description
UPSMonitorSetup
PropertyDescription
Notes
Example
RuntimeCalibration
Description
Notes
Example
UPSMonitoring
PropertyDescription
Example
General Information
Summary
 0$! 

 	
  
 +$3 0$! 

 
	
 
 `	
a 
	
 ( 	 !-:-  0!)




  	
 
	 
 

 	

	
...

Page 483

Packages required:ups
License required:level1
Home menu level:/system ups
Standards and Technologies:APCssmartprotocol
Hardware usage:Not significant
Description
Cabling
 	 +$3 0$! &)	0$! $  !	
0$! 8 	 	 	 	 &
 


 
 0!)
* 
 	 	 
 
 0$! 	 	 	    +$3  
 	
  	 H
7H 0 


 		
Router Side (DB9f)SignalDirectionUPS Side (DB9m)
2ReceiveIN2
3SendOUT1
5Ground4
7CTSIN6
9
 
	
  	 	 ...

Page 484

nominal-battery-voltage(read-only: integer) - the UPSs nominal battery voltage rating (this is not
the UPSs actual battery voltage)
offline-after(read-only: time) - when will the router go offline
offline-time(time; default:5m) - how long to work on batteries. The router waits that amount of
time and then goes into hibernate mode until the UPS reports that the utility power is back
•0- the router will go into hibernate mode according the min-runtime setting and 10% of battery
power event. In this case,...

Page 485

Example
[admin@MikroTik] system ups> rtc 0
UPS Monitoring
Command name:/system ups monitor
Property Description
battery-charge(percentage) - the UPSs remaining battery capacity as a percent of the fully
charged condition
battery-voltage- the UPSs present battery voltage. The typical accuracy of this measurement is
±5% of the maximum value (depending on the UPSs nominal battery voltage)
frequency(percentage) - when operating on-line, the UPSs internal operating frequency is
synchronized to the line within...

Page 486

output-voltage: 226Vload: 45%temperature: 39Cfrequency: 50Hzreplace-battery: nosmart-boost: nosmart-trim: nooverload: nolow-battery: no
[admin@MikroTik] system ups>
6
 


 
 	


[admin@MikroTik] system ups> monitor 0on-line: noon-battery: yestransfer-cause: Line voltage notch or spikeRTC-running: noruntime-left: 19moffline-after: 4m46sbattery-charge: 94%battery-voltage: 24Vline-voltage: 0Voutput-voltage: 228Vload: 42%temperature: 39Cfrequency: 50Hzreplace-battery: nosmart-boost: nosmart-trim:...

Page 487

VRRP
Document revision 1.6 (February 6, 2008, 4:08 GMT)
This document applies to MikroTik RouterOS V3.0
Table of Contents
TableofContents
GeneralInformation
Summary
Specifications
Description
Notes
VRRPRouters
Description
PropertyDescription
Notes
AsimpleexampleofVRRPfailover
Description
ConfiguringMasterVRRProuter
ConfiguringBackupVRRProuter
Testingfailover
General Information
Summary
O
	 
 
	
 $
 &O$ 

	

 
 
  
 !  #3-::C 	


O$ 
 ...

Page 488

	
 
 	 (
	 
 + 
  	 (
	 
 	
  
 
  
 
 
	

•?.0#83
	
 
 
 
 	
 	 
 8
 
 
 

	
% *$ 	  	 

 
 +!F 
 
 	 (
	 
  
 
 O$ 	(


 	
 
 	 

	 
 &
 
	
 	 ( 
 
 	  &
 




•I.,AN5
	
 
 
 O$ 
 

 
 	(		
 	
 
	
  
 	
 
 *
 


 	
 	
 8
 
 
 ...

Page 489

name(name) - assigned name of the VRRP instance
on-backup(name; default:) - script to execute when the node switch to backup state
on-master(name; default:) - script to execute when the node switch to master state
password(text; default:) - password required for authentication depending on method used can
be ignored (if no authentication used), 8-character long text string (for plain-text authentication) or
16-character long text string (128-bit key required for AH authentication)
preemption-mode(yes |...

Page 490

O$ 
 	   
 	 	 
	

 *



 



 
 	 	7( A
  	

	
  	( /;-/GC/.1-D 

 	
  
 
 (  	(		 *



 



  

 

   9+
 &
 	 	7( 
  *$   
	 

 
 	
)I$   !$# 

 
 O$ 6 	( 



 
 
 

 *



 !( $( &*!$
	
 
  
   & 	 
  	  	

 	   
...
Start reading MikroTik Router OS V3.0 User Manual
All MikroTik manuals