Miele W1712 User Manual

							Front view
aInlet hose (tested to withstand
pressure of at least 7,000 kPa)
bElectricity supply cable
c-fFlexible drain hose (with
detachable swivel elbow)
gDetergent dispenser drawerhControl panel
iDrum door
jAccess to drain filter, drain pump
and emergency release
kHandle recesses for moving the
machine
lFour height adjustable feet
Installation and connection
41 
						

							Rear view
aProtruding lid for holding when
moving the machine
bElectricity supply cable
cInlet hose (tested to withstand
pressure of at least 7,000 kPa)
dDrain hoseeTransit bar covers
fRestraining clip for inlet hose and
drain hose
gRestraining clips for transit bars
when removed
Installation and connection
42 
						

							Installation surface
A concrete floor is the most suitable
installation surface for a washing
machine, being far less prone to
vibration during the spin cycle than
wooden floorboards or a carpeted
surface.
Please note the following points:
^The machine must be level and
securely positioned.
^To avoid vibrations during spinning,
the machine should not be installed
on soft floor coverings.
If installing on a wooden joist floor:
^We recommend a plywood base (at
least 59x52x3 cm). The base should
span several joists and be bolted to
the joists and not only to the
floorboards. Check for the presence
of pipes and cables first.
If possible, install the machine in a
corner, as this is usually the most stable
part of the floor.Transporting the machine to its
installation site
To manoeuvre the machine out of its
packing case to its installation site, hold
it by the front feet as well as by the
edge of the lid where it protrudes to the
rear of the washing machine.
,Ensure that the machine feet and
the floor are dry to prevent the
machine from slipping during the
spin cycle.
Removing the transit fittings
^
To remove the left and right covers
1. Use a screwdriver to prise out the
cover as illustrated.
2. Pull the cover forwards to remove.
Installation and connection
43 
						

							^Using the spanner supplied, turn the
left-hand transit bar 90°, then
^
withdraw the transit bar.^Turn the right-hand transit bar 90°,
then
^
withdraw the transit bar.
Installation and connection
44 
						

							,To avoid the risk of injury the
holes for the transit bars must be
covered after the transit bars have
been removed.
^Fit the covers onto the two holes.
Then plug the holes as shown with
the caps.^Secure the transit bars to the back of
the washing machine. Make sure that
holesbare fitted over retainersa.
,The machine must not be moved
without the transit bars in place.
Store them as shown or keep them
in a safe place for future use. They
must be re-fitted if the machine is to
be moved again (e.g. when moving
house).
Re-fitting the transit bars
Re-fitting is carried out by reversing the
procedure.
Installation and connection
45 
						

							Levelling the machine
The machine must stand perfectly level
on all four feet to ensure safe and
proper operation.
Failure to level the machine can result
in the machine banging in the spin
cycle or walking across the floor
during operating.
Screwing out and adjusting the feet
The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.
^
Using the spanner supplied turn
counter nut2in a clockwise
direction. Then turn counter nut2
together with foot1to unscrew.^Use a spirit level to check the
machine is standing level.
^Hold foot1securely with a pipe
wrench. Turn counter nut2again
using the spanner supplied until it
sits firmly up against the housing.
,All four counternuts must be
firmly up against the housing. Please
also check this for the feet which did
not need adjustment. Otherwise
there is the danger of the machine
moving about.
Installation and connection
46 
						

							This washing machine is not suitable
for building under a worktop.
However, you can push your machine
under a worktop if there is space to do
this.
Washer-dryer stack
A Miele tumble dryer can be stacked
with the washing machine. A WTV
stacking kit is necessary which can be
purchased from your Chartered Agent
or the Miele Spare Parts Department.Please note:
aSafety distance to wall:
at least 2 cm
bHeight:
Stacking kit with pull-out shelf:
approx. 172 cm
Stacking kit without pull-out shelf:
approx. 170 cm
cDepth of the washer-dryer stack:
approx. 65 cm
Installation and connection
47 
						

							The Miele water protection
system
The Miele water protection system
protects all parts of the washing
machine from water damage.
The system consists of three main
components:
1) the inlet hose
2) the electronic unit and the washing
machine housing
3) the drain hose
1) Inlet hose
– The inlet hose can withstand
pressure of more than 7000 kPa.
2) Electronic unit and washing
machine housing
– Sump
Any leaking water is collected in a
sump in the base of the machine. A
float switches off the safety valves,
preventing any more water flowing
into the machine and water in the
suds container is pumped away.–Overflow protection
This prevents the washing machine
taking in too much water. If the water
level exceeds a certain level, the
drain pump switches in and pumps
the excess water away.
3) Drain hose
The drain hose is protected by a
ventilation system which prevents the
washing machine from being
emptied completely.
Installation and connection
48 
						

							Connection to the water
supply
The machine should be connected to a
mains water supply in accordance with
current local and national safety
regulations.
The machine is designed to operate
with a flow pressure of between
100 kPa and 1000 kPa. If it is higher
than 1000 kPa it is essential to fit a
pressure reducing valve.
Connection to the mains water supply
should incorporate a mains tap with
3/4
thread. The tap should be fitted by a
qualified plumber.
,The connection point is subject
to mains water pressure. Turn on the
tap slowly and check for leaks.
Correct the position of the washer
and union if appropriate.
The washing machine isnotsuitable
for connection to a hot water supply,
and connection to a household
water softener is not recommended.
Maintenance and care
Only use a genuine Miele hose should
you ever need a replacement or
extension. These are tested to
withstand pressure of at least 7000 kPa.
In order to protect the water inlet
valve, the two dirt filters - one in the
open end of the inlet hose, one at
the inlet point in the machine, must
not be removed.
Extension hose
–Longer hoses 2.5 or 4.0 m in length
are available from the Miele Spare
Parts Department as optional extras.
Installation and connection
49 
						

							Connection to the drainage
system
The machine drains via a drain pump
with a delivery head of 1 metre*. The
drain hose must not be kinked as this
restricts drainage. The swivel elbow at
the end of the hose can be turned in
either direction, or can be detached if
required, with a sharp twist and pull.
If required, the drain hose can be
extended to a length of 5 m. The
necessary parts can purchased from
the Miele Spare Parts Department.
* For a delivery head of more than 1 m
(up to a max. of 1.8 m) a second
duo-drain pump is available with the
corresponding kit from the Miele Spare
Parts Department.
Drain hose connection:
1. Direct into a sink or basin:
Please note the following:
–
Hook the hose over the edge and
secure.
–
Make sure that the water can drain
away freely without hindrance.
Otherwise there is a risk of water
overflowing or of some of the drained
water being sucked back into the
machine.
2. Connected securely to a plastic
drain pipe with a rubber nipple.
There is no need to use a non-return
valve.
3. Connected securely to a standpipe.
4. Connected securely to a floor gully.Please note:
aAdapter
bNut
cHose clip
dEnd of the hose
^Fit adapterato the sink drain outlet
using nutb.
^Attach the end of the hosedto
adaptera.
^
Use a screwdriver to tighten hose
clipcup close to the nut.
Installation and connection
50