Miele T 8823 C Manual

Extending the drying level for
the Minimum iron
programme
The electronics of this dryer ensure a
very effective and energy-efficient
drying process.
You can, however, extend the range
of the drying level in this programme.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for...

Anti-crease setting
Helps prevent creasing if laundry is
not normally removed immediately
after the end of a programme.
Anti-crease
–is set as a standard setting. You can
shorten the time or switch it off
completely.
–can be used for all programmes,
exceptWoolens handcare.
–should always be switched on.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst...

Altering the volume of the
buzzer
The buzzer has two volumes.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
–The dryer is switched off.
–The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for the
Start/Stopbutton lights up constantly
...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton
three times.
– TheLow...

Extending the drying level for
the Automatic plus
programme
The electronics of this dryer ensure a
very effective and energy-efficient
drying process.
You can, however, extend the range
of the drying level in this programme.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for...

Extending the cooling down
time
The cooling down phase which takes
place before the end of a programme
can be lengthened if required. This
makes the garments easier to handle.
The cooling down time is only available
for programmes with drying levels.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait...

Standby
To save energy, the display goes out
after 10 minutes and the indicator
light for theStart/Stopbutton will start
flashing slowly.
Reactivate from Standby
Turning the programme selector or
pressing one of the buttons switches
the display back on again. This will
not alter a running programme.
On
Standby is activated:
– if a programme is not selected after
the machine has been switched on.
– after a programme has started.
However: The display will switch on for
10 minutes if Delay start has...

Before you begin, first ensure that:
–The dryer is switched off.
–The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for the
Start/Stopbutton lights up constantly
...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton six
times.
– TheLow temperatureindicator light
will briefly flash on and off eight
times.
The option selected will be displayed
by anumberwhich will alternate...

Memory function
The electronics will memorise any
Extra options selected for a
programme. The duration selected
for the timed drying programmes will
also be stored in memory.
These settings will be selected
automatically the next time the
programme is chosen. You can either
accept these or change them by
pressing the appropriate button.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.

Press...

Clean out airways indicator
Fluff should be removed after drying.
The Clean out airways indicator will
remind you toClean the filterswhen a
certain amount of fluff has collected
in the filters. You can decide at what
level of fluff this reminder should be
given.
You will have an idea of how often this
should be done after a few drying
programmes.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.

Press...

Keypad tone
An audible tone sounds each time a
button is pressed.
Follow steps (
,,...) to
programme and store in memory.
Before you begin, first ensure that:
–The dryer is switched off.
–The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until the indicator light for the
Start/Stopbutton lights up constantly
...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton
nine times.
– The indicator lightLow...