Miele T 8823 C Manual

Pull the condenser unit out of its
housing by the handle.
Checking the condenser unit

Hold the condenser unit up to the
lightas shown.

Check to see if there is any fluff
inside it.
The arrows in the illustration above
indicate where to look.If you cannot see any fluff:
Replace the condenser unit (see
following page).
If you can see some fluff:
Clean the condenser unit as
described below.
Cleaning the condenser unit
When rinsing the condenser unit,
make sure you position it as
shown in the next...

Then flush the unit through from the
front.
Check the condenser unit again for
any visible fluff and if necessary flush
it through again until it has all gone.
Remove any soiling still visible inside
the housing unit.
Also make sure the rubber seals are
clean.
The rubber seals must not be
removed and must be free of kinks.

Shake any excess water out of the
unit until no more water droplets are
visible.Replacing the condenser unit
With the handle facing upwards,
push the condenser unit back into...

Problem solving guide
Most faults can be resolved by yourself. This will save time and money as a
call-out charge will apply to customer service visits where the problem could have
been rectified as described in these Operating instructions.
With the help of the following notes, minor faults in the performance of the
appliance, some of which may result from incorrect operation, can be put right
without a call-out being necessary. Please note:
Repair work to electrical appliances must only be carried out...

Problem Possible cause Remedy
The following
flashes at the
end of a
programme:
—œ–...C~–...Cœ˜...The programme has finished
but the laundry is still cooling
down.You can remove the laundry
and spread it out to allow the
heat to dissipate, or leave it in
the dryer to cool down more.
TheClean out
airways
indicator light
comes on.The dryer is not working
efficiently or economically.
Possible cause: Blockages
due to fluff or detergent
residues.–Cleaning the filters is
usually all that is required.
However,...

Problem Possible cause Remedy
The indicator light
Start/Stopflashes
slowly and the display
is dark.The dryer is on standby.
This is a normal function
and does not indicate a
fault.See Programmable
functions.
Some programmes
wont start anymore.
The indicator light for
that programme doesnt
light up anymore either.There is no immediate
cause.–Switch the dryer off
and then on again.
–Select the programme
that cannot be started.
–If you still cant start the
programme, there is a
fault. Contact Miele....

An unsatisfactory drying result
Problem Possible cause Remedy
The laundry is not
sufficiently dry.The load consisted of
different fabrics.–Final drying cycle with
Warm air.
–Select a different
programme next time*.
Items made of synthetic
fibres are charged with
static electricity after
drying.Synthetic fibres tend to
attract a static charge.Static charges can be
reduced by adding a
fabric conditioner to the
final rinse in the washing
programme or a fabric
conditioner sheet to the
load when drying.
There...

Other problems
Problem Possible cause Remedy
The drying process
goes on too long or
even switches off.In some circumstances, the
Clean out airways indicator
light still comes on, even
though the filters are clean.
Clean out airways.Please check all the
possible causes and
switch the dryer off and
then back on again.
Ventilation to and from the
dryer may be insufficient
(e.g. because it is installed
in a small room). This has
caused the temperature in
the room to rise sharply.Open a door or window
while...

Problem Possible cause Remedy
Water leaks from the
machine after the
condenser unit has
been cleaned.–The inner cover of the
condenser unit has not
been locked properly
and/or the condenser
unit has not been
positioned correctly.
–There is a build-up of
fluff.–Ensure that the
condenser unit is
positioned correctly
and lock the inner
cover.
–Check the rubber
seals.
–Use a cloth to remove
any visible fluff from the
inside of the condenser
unit housing.
A programme cannot be
started.There is no immediate...

Changing the lamp
Disconnect the machine from the
mains electricity supply.
Open the door.
You will find the interior lamp cover at
the top of the drum aperture.
Insert a suitable tool, such as a wide
bladed screwdriver, under the side
edge of the lamp cover as illustrated.

Apply a little pressure and, whilst
doing so, turn your wrist in the
direction of the arrow to open the
cover.
The cover will open downwards.
The temperature resistant lamp should
only be ordered from your Miele
Chartered Agent or...

In the event of any faults which you
cannot remedy yourself, please contact
–Your Miele Chartered Agent or
–Miele (see back cover for address).
When contacting Miele, please quote
the model and serial numbers, both of
which are located on the data plate
situated on the right-hand side below
the drum aperture.Future updates (PC)
The indicator or check light markedPC
on the control panel is the interface
used by the Miele service technicians
during service work for testing
purposes and for updating the...