Miele T 8822 C Manual

Changing the lamp
Disconnect the tumble dryer from
the mains electricity supply.
Open the door.
You will find the interior light cover at
the top of the drum aperture.
Insert a suitable tool, such as a wide
bladed screwdriver, under the side
edge of the light cover as illustrated.

Apply a little pressure and whilst
doing so turn your wrist in the
direction of the arrow to open the
cover.
The cover will open downwards.
The temperature resistant lamp should
only be ordered from your Miele Dealer
or the...

Repairs
In the event of any faults which you
cannot remedy yourself, please contact
–your Miele dealer or
–the Miele Service Department (see
back cover for contact details).
When contacting your dealer or the
Service Department, please quote the
model and serial number of your
appliance, both of which are shown on
the data plate. This is visible when you
open the door.
N.B. A call-out charge will be
applied for service visits where the
problem could have been resolved
as described in these instructions....

Front view
Mains connection cable
Condensed water container
Control panel
DoorService panel for condenser unit
Four height-adjustable screw feet
External drainage options (e.g. via
wash basin, wash basin drain outlet,
or gully. See External condensed
water outlet).
Installation
43 

Rear view
Protruding lid for holding when
moving the dryer (see arrows)
Air inlet vent for cooling the
condenser unit
Mains connection cable
Hose for external drainage of
condensed water
Accessories for connection to a sink
drain outlet
Installation site
Make sure the dryer door can be
opened without hindrance after
installation.
Transporting the dryer to its
installation site
When moving the dryer, hold it by the
lid where it protrudes to the rear. To
manoeuvre the dryer out of its packing
case to...

Levelling the appliance 
The dryer must be perfectly level to 
ensure safe and proper operation. 
 The screw feet can be adjusted to 
compensate for any unevenness in
the floor.
The air inlet and outlet vents on 
the front of the dryer must not be
covered as this would prevent
sufficient ventilation for cooling the
condenser unit.
Do not block the gap between
the bottom of the tumble dryer and
the floor with plinth facings, deep
pile carpet etc. This would hinder a
sufficient flow of air to the dryer....

External condensed water
outlet
General notes
When drying is in progress, condensed
water is pumped into the condensed
water container through the drain hose at
the back of the dryer. The condensed
water can also be drained off directly if
the tumble dryer is installed near a sink,
drain outlet etc. so that the condensed
water container does not have to be
emptied.
Drain hose length............1.50 m
Maximum delivery head.......1.50 m
Maximum drain hose length....4.00 m
If the on-site water drainage...

External drainage via a sink or gully
See Front view illustration.
If you want to drain the water off
into a sink you will need to secure
the hose carefully, e.g. by tying it to
a tap to make sure it cannot slip
during use. Otherwise there is a risk
of overflowing water which could
cause damage.
Use the bow-shaped guide to
prevent the drain hose from
becoming kinked.
Installation conditions requiring a
non-return valve
Certain installation conditions
require the fitting ofa non-return
valve for...

1 Adapter
2 Nut
3 Hose clip
4 End of the hose
5 Non-return valve
6 Tumble dryer drain hoseFit adapter1to the sink drain outlet
using nut2.
If this nut has a flat disc in it you
should take the disc out first.
Attach the end of hose4to adapter
1.
Use a screwdriver to tighten hose
clip3up close to the nut.
Non-return valve5has to be
fitted with the arrow pointing in the
direction of flow (i.e. towards the
sink). Otherwise water will not drain
out of the appliance.
Fit non-return valve5to tumble dryer...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person, in strict accordance with
current national and local safety
regulations (BS 7671 in the UK).
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains
supply. Please ensure the connection
data quoted on the data plate match
the household mains...

Load1Final spin speed
in a domestic washing
machineResidual
moistureEnergy Duration
kg rpm % kWh Minutes
Cottons27.0
3.51000
100060
604.14
2.28109
65
Cottons Normal7.0
7.0
7.0
7.01200
1400
1600
180053
50
44
433.75
3.55
3.15
3.10100
95
86
84
Cottons Normal
+ Low temperature7.0 1000 60 4.20 175
Cottons Hand iron7.0
7.0
7.0
7.0
7.01000
1200
1400
1600
180060
53
50
44
433.10
2.75
2.55
2.20
2.1089
79
74
65
63
Minimum iron Normal3.5 1200 40 1.40 45
Minimum iron Normal
+ Low temperature3.5 1200 40 1.50 73...