Miele Kfn 8995 Seed Operating And Installation Instructions

. . . the interior lighting or the door
lighting is not working?
^The refrigerator section door may
have been left open for too long.
The lighting automatically switches
off after the door has been open for
approx. 15 minutes.
If the door to the refrigerator section
has been open for less than 15
minutes, and the lighting does not work,
then there is a fault. Call the Miele Ser
-
vice Department.
Do not use force to open the
glass-edge lighting. Danger of
injury.
. . . the floor of the refrigerator is...

Normal noises What causes them?
Brrrrr...Humming noise made by the motor (compressor). This noise
may get louder for brief periods, whenever the motor kicks in.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds occur whenever the thermostat switches the
motor on or off.
Sssrrrrr....In multi-zone and frost-free appliances, the movement of air
circulating through the appliance can sometimes just barely be
heard.
Please bear in mind that a...

In the event of a fault that you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–the Miele Service Department (see
back cover for address).
When contacting your Dealer or the
Service Department, please quote the
model and serial number of your
appliance. This information is shown on
the data plate.
Please note that telephone calls may
be monitored and recorded for
training purposes.
After-sales service
43
 

The machine must be connected to
the water supply by a licensed
plumber in accordance with local
and national regulations. The water
being used should have the drinking
water standards of the respective
country where the machine is used.
–All units and systems used to deliver
the water to the appliance must
conform with the requirements of the
respective country.
–The machine is designed to be
plumbed to a cold water connection.
– The on-site water line must have a
water valve to turn the water off if...

^Open the valve for water supply and
check entire water system for leaks.
Before using the appliance for the first
time, a licensed plumber should bleed
air from the system.
^Please use caution.
^Slide the appliance into the desired
position.
After a maximum of 24 hours the first
ice cubes will drop out of the ice
cube maker and collect in the
drawer.
Plumbing (may vary by model)
45
 

The appliance is delivered ready for
connection to a 60 Hz, 115 V power
supply. It is only suitable for plugging
into a properly grounded socket that
complies with regulations. The
appliance must only be plugged into a
wiring system that complies with the
local Electrical Code.
The fuse must be rated at least 10 A.
Ideally, the socket should be next to the
appliance and easily accessible. Do
not connect the appliance to the power
supply by an extension cord. Extension
cords do not guarantee the required...

Do not place any items that produce
heat on top of the appliance (such
as a toaster or microwave). This will
increase the amount of energy the
appliance consumes.
This fridge/freezer should not be
placed in a side-by-side formation
with a second model. Because the
appliance does not have heated
side walls, a side-by-side
arrangement can lead to the
build-up of condensation water.
Contact your dealer for advice.
Location
The appliance should not be installed
directly next to a heat source (such as
a...

Adjustments
^Use the flat wrench provided to
adjust the feet as needed, so that the
appliance is even all around.
Installation information
48
 

The appliance is supplied with a
right-hand hinge. If left-hand door
hinging is required, follow the
instructions below.
Check that the appliance has been
disconnected from the electricity
supply and unplugged. Danger of
electric shock.
To change the door hinging, you will
need various sizes ofTorx
screwdrivers, a pair offlat-nosed
pliersand awrench.
Removing the door handles:
First, the side sections of the handles
must be removed:
^
Pull door handleatowards you. Side
sectionbslides back, creating a...

^Using a wrench, unscrew the hinge
pins from hinge bracketb, and refit
all hinge partscin the hinge bracket
on the opposite side.
Removing the refrigerator section
door:
^Remove the bearing block cover on
top of the appliance. To do this:
Using a screwdriver, carefully pry the
bearing block cover off from behind.
^Open the door to the refrigerator
section.
^
Remove the cover (see illustration).^Open the plug holder out towards
you, and use it to pull the plug out.
^Pull the cable carefully upwards from...