Miele Kfn 14943 Sd Operating And Installation Instructions

^Remove the coverd.
Now the soft-close mechanism and the
appliance are no longer connected.
^Remove the panela.
^Push the shock absorber armfas
far as possible towards the handle
side.
^Loosen the three screwsgon the
soft-close mechanism and the
spacer.
^In the middle, pry out the housing
with the soft-close mechanism using
a flathead screwdriver.
^
Then, pry the housing with the
soft-close mechanism out of the
retainer from the appliance side.
^
Lay the soft-close mechanism aside.
^
Push out the spacer...

Caution! The top door of the
appliance is no longer secured as
soon as the hinge bracket is
removed when following the
instructions below!
^Close the top door of the appliance.
^Loosen the screwsmon the top
hinge bracketnand remove the
hinge bracket by pulling up.
^Carefully lift and remove the top door
of the appliance and set aside.
^Make sure that the bearing pin in the
middle of the appliance stays in
place, otherwise the bottom door of
the appliance has no hold!
^Engage the coverhtogether with
the...

^Push the pineup and out.
Now the soft-close mechanism and the
appliance are no longer connected.
^Remove the panela.
^
Push the shock absorber armfas
far as possible towards the handle
side.
^
Loosen the three screwsgon the
soft-close mechanism and the
spacer.
^
In the middle, pry out the housing
with the soft-close mechanism using
a flathead screwdriver.
^
Then, pry the housing with the
soft-close mechanism out of the
retainer from the appliance side.
^
Lay the soft-close mechanism aside.
^
Push out...

^Lift the plugslout of the door
bearing bushing in the appliance
door and place it on the other side.
Mounting the bottom door of the
appliance:
^
Remove the coveratowards the
front.
^
Pull the coverboff.
^
Screw the adjustment foot at the
bearing pinccompletely in.^With the assistance of another person,
carefully tilt the appliance backwards
and pull the bearing pincdown and
out.
^Pay attention to the hinge bushingd.
^Loosen the screwseand remove the
hinge bracketf.
^Remove the covergand loosen the...

^Put the bearing piniin the middle
of the appliance through the hinge
bracketkinto the bottom door of the
appliance.
Mounting the bottom soft-close
mechanism:
^
Remove the coverafrom the panel
b, turn it 180° and replace it on the
other side.^Hook the spacer on the handle side
into the retainer (A).
^Hook the soft-close mechanism into
the retainer (B) on the appliance
side.
Push both parts outwards until they
engage.
^
With the three screwsc, first screw
on the spacer on the handle side and
then the...

^Hang the panelbon the shock
absorber armd.
^Pull the shock absorber armd
towards the hinge bracket and insert
the pinefrom the top so that the
square rests in the recess.
^Put on the coverfin such a way
that it engages.
Take care that the coverfsits
correctly to ensure that the door closes
properly and the pin is secured.
^Remove the securing deviceg.
^
Place the panelbonto the soft-close
mechanism from above, engaging it
at the bottom first and then at the top.
^
Close the bottom door of the...

Mounting the top soft-close
mechanism:
^Remove the coverafrom the panel
b, turn it 180° and replace it on the
other side.
^
Hook the spacer on the handle side
into the retainer (A).
^
Hook the soft-close mechanism into
the retainer (B) on the appliance
side.
Push both parts outwards until they
engage.^With the three screwsc, first screw
on the spacer on the handle side and
then the soft-close mechanism on the
appliance side.
^Hang the panelbon the shock
absorber armd.
^
Push the covereon from the side...

^Remove the securing deviceg.
^Place the panelbonto the soft-close
mechanism from above, engaging it
at the bottom first and then at the top.
^Close the top door of the appliance.
Remounting the door handles:
The following instructions must be
followed when attaching the door
handle, otherwise the door seal
could be damaged.
^
First, loosely screw the door handle
onto the opposite side with the two
front screwsb.The mounting platecmust be
positioned on the door housing in such
a way that when the door...

The appliance doors can be aligned
with the appliance housing afterwards.
In the following figure, the appliance
door is not closed so that the
individual steps can be seen more
clearly.
Align thebottom doorin the bottom
hinge bracket via the outer, elongated
holes:
^Remove the middle screwafrom the
hinge bracket.
^
Loosen the two outer screwsb
slightly.
^
Align the appliance door by moving
the hinge bracket to the right or left.
^
Tighten the screwsb; the screwa
does not need to be screwed on...

aadapter cabinet
bappliance
ckitchen cabinet
dwall
The appliance can be installed in any
fitted kitchen. To match the appliance
to the height of the fitted kitchen, a
suitable adapter cabinetacan be
installed over the appliance.
A ventilation gap of at least 2 inches
(50 mm) must be provided between the
adapter cabinet and the kitchen wall.
The ventilation cross-section below the
room ceiling must be at least 46 in
2
(300 cm2) so that warm air can escape
without obstruction. Otherwise the
appliance has...