Miele Kfn 14943 Sd Operating And Installation Instructions

							^Remove the coverd.
Now the soft-close mechanism and the
appliance are no longer connected.
^Remove the panela.
^Push the shock absorber armfas
far as possible towards the handle
side.
^Loosen the three screwsgon the
soft-close mechanism and the
spacer.
^In the middle, pry out the housing
with the soft-close mechanism using
a flathead screwdriver.
^
Then, pry the housing with the
soft-close mechanism out of the
retainer from the appliance side.
^
Lay the soft-close mechanism aside.
^
Push out the spacer towards the
hinge side.
^
Lay the spacer aside.Removing the top door of the
appliance:
^Loosen the coverhby carefully
sliding a flathead screwdriver from
below into the recess.
^Remove the coverhtogether with
the mounting bracketi.
^Loosen the mounting bracketifrom
the coverhby pushing it slightly to
the left and then removing the cover
plate towards the front.
^Turn the mounting bracketi180°.
^
Place the coverhonto the front of
the mounting bracketiand push it
to the right. The writing must be
visible.
^
Unscrew the bearingjmechanism,
turn it 180° and replace it on the
opposite side. If necessary,
pre-punch the screw holes.
^
Remove the top coverkby pushing
it from back to front and lifting it up.
^
Remove the coverlupwards.
Changing the door hinging
51
 
						

							Caution! The top door of the
appliance is no longer secured as
soon as the hinge bracket is
removed when following the
instructions below!
^Close the top door of the appliance.
^Loosen the screwsmon the top
hinge bracketnand remove the
hinge bracket by pulling up.
^Carefully lift and remove the top door
of the appliance and set aside.
^Make sure that the bearing pin in the
middle of the appliance stays in
place, otherwise the bottom door of
the appliance has no hold!
^Engage the coverhtogether with
the mounting bracketion the
opposite side.
^Now place the coverlon the other
side.
Removing the bottom soft-close
mechanism:
^
Open the bottom door of the
appliance.^Loosen the panelaof the soft-close
mechanism: Slowly pry the panel off
from the top.
Be careful not to damage the door
seal.
If the door seal is damaged, the
appliance door may not close
properly and there will not be
enough refrigeration!
^Slide the panelain the direction of
the appliance and leave it hanging
between the door and the appliance.
^
Place the securing deviceb
(supplied with the appliance) on the
soft-close mechanismc.
With the securing device in place, the
joint cannot snap shut. Do not remove
the securing device until instructed to!
^
From the side, carefully lift off the
coverdusing a flathead
screwdriver.
^
If necessary, lift the appliance
backwards slightly with the
assistance of another person.
Changing the door hinging
52
 
						

							^Push the pineup and out.
Now the soft-close mechanism and the
appliance are no longer connected.
^Remove the panela.
^
Push the shock absorber armfas
far as possible towards the handle
side.
^
Loosen the three screwsgon the
soft-close mechanism and the
spacer.
^
In the middle, pry out the housing
with the soft-close mechanism using
a flathead screwdriver.
^
Then, pry the housing with the
soft-close mechanism out of the
retainer from the appliance side.
^
Lay the soft-close mechanism aside.
^
Push out the spacer towards the
hinge side.^Lay the spacer aside.
Removing the bottom door of the
appliance:
^Close the bottom door of the
appliance.
^Pull the bearing piniin the middle
of the appliance up and out.
^Carefully lift and remove the bottom
door of the appliance and set aside.
^Pull the coverdoff.
^
Unscrew the hinge brackete, rotate
it 180°, then screw it onto the
opposite side.
^
Turn the plastic caph180° and
replace it on the hinge bracketkin
the middle.
^
Now place the coverlon the other
side.
Changing the door hinging
53
 
						

							^Lift the plugslout of the door
bearing bushing in the appliance
door and place it on the other side.
Mounting the bottom door of the
appliance:
^
Remove the coveratowards the
front.
^
Pull the coverboff.
^
Screw the adjustment foot at the
bearing pinccompletely in.^With the assistance of another person,
carefully tilt the appliance backwards
and pull the bearing pincdown and
out.
^Pay attention to the hinge bushingd.
^Loosen the screwseand remove the
hinge bracketf.
^Remove the covergand loosen the
screw. Attach both to the other side.
^Screw the hinge bracketfonto the
other side with the twoouterscrews.
Do not use themiddlescrew; this
allows later alignment of the appliance
door using the outer, elongated holes!
^Unscrew the bearing parthfrom the
hinge bracketf, turn it 180° and
screw it into the opposite hole of the
hinge bracket.
^Now place the coverbon the other
side.
^With the assistance of another
person, carefully tilt the appliance
backwards and insert the bearing pin
cinto the hinge bracketffrom
below. The groove in the bottom of
the hinge bracket faces forwards.
^
Place the hinge bushingdonto the
bearing pinc.
^
Put the coveraon.
^
Place the lower door of the appliance
onto the bearing pincfrom above.
^
Close the bottom door of the
appliance.
Changing the door hinging
54
 
						

							^Put the bearing piniin the middle
of the appliance through the hinge
bracketkinto the bottom door of the
appliance.
Mounting the bottom soft-close
mechanism:
^
Remove the coverafrom the panel
b, turn it 180° and replace it on the
other side.^Hook the spacer on the handle side
into the retainer (A).
^Hook the soft-close mechanism into
the retainer (B) on the appliance
side.
Push both parts outwards until they
engage.
^
With the three screwsc, first screw
on the spacer on the handle side and
then the soft-close mechanism on the
appliance side.
Changing the door hinging
55
 
						

							^Hang the panelbon the shock
absorber armd.
^Pull the shock absorber armd
towards the hinge bracket and insert
the pinefrom the top so that the
square rests in the recess.
^Put on the coverfin such a way
that it engages.
Take care that the coverfsits
correctly to ensure that the door closes
properly and the pin is secured.
^Remove the securing deviceg.
^
Place the panelbonto the soft-close
mechanism from above, engaging it
at the bottom first and then at the top.
^
Close the bottom door of the
appliance.Mounting the top door of the
appliance:
^Place the top door of the appliance
onto the bearing piniin in the
middle of the appliance.
^Close the top door of the appliance.
^Put the hinge bracketnon the
opposite side and and fasten it with
the screwsm.
The screw holes may have to be
pre-punched or use a power
screwdriver.
^
Now place the coverkon the other
side.
^
Align the appliance door with the
appliance housing via the elongated
holes in the bottom hinge bracket .
Tighten the screws.
Changing the door hinging
56
 
						

							Mounting the top soft-close
mechanism:
^Remove the coverafrom the panel
b, turn it 180° and replace it on the
other side.
^
Hook the spacer on the handle side
into the retainer (A).
^
Hook the soft-close mechanism into
the retainer (B) on the appliance
side.
Push both parts outwards until they
engage.^With the three screwsc, first screw
on the spacer on the handle side and
then the soft-close mechanism on the
appliance side.
^Hang the panelbon the shock
absorber armd.
^
Push the covereon from the side so
that the openings for the pinfare
on top of each other.
^
Pull the shock absorber armd
towards the hinge bracket and insert
the pinffrom the top so that the
square rests in the recess.
^
Then engage the covere
completely.
Take care that the coveresits
correctly to ensure that the door closes
properly and the pin is secured.
Changing the door hinging
57
 
						

							^Remove the securing deviceg.
^Place the panelbonto the soft-close
mechanism from above, engaging it
at the bottom first and then at the top.
^Close the top door of the appliance.
Remounting the door handles:
The following instructions must be
followed when attaching the door
handle, otherwise the door seal
could be damaged.
^
First, loosely screw the door handle
onto the opposite side with the two
front screwsb.The mounting platecmust be
positioned on the door housing in such
a way that when the door isclosedthe
mounting plate is aligned with the
outside wall of the appliance.
If this alignment is off, you can correct it
by
^turning both of the pre-mounted set
screwsawith a wrench until the
mounting platecis at the correct
angle.
^Tighten all 4 screwsb.
^From the appliance side, slide the
sidebardonto the guide for the
mounting plate, until it audibly
engages.
Make sure that the sidebarddoes
not come in contact with the door
seal when the door is opened. This
would damage the door seal over
time.
If you see that the sidebar is coming
into contact with the door seal,
^
adjust the mounting platecagain
using the set screwsauntil the
mounting plate and the sidebard
are at the correct angle and the
sidebar no longer touches the seal
when the door is opened.
Changing the door hinging
58
 
						

							The appliance doors can be aligned
with the appliance housing afterwards.
In the following figure, the appliance
door is not closed so that the
individual steps can be seen more
clearly.
Align thebottom doorin the bottom
hinge bracket via the outer, elongated
holes:
^Remove the middle screwafrom the
hinge bracket.
^
Loosen the two outer screwsb
slightly.
^
Align the appliance door by moving
the hinge bracket to the right or left.
^
Tighten the screwsb; the screwa
does not need to be screwed on
again.Align thetop doorvia the elongated
holes in the middle hinge bracket:
^Loosen the three screwscslightly.
^Align the appliance door by moving
the hinge bracket to the right or left.
^Tighten the screwsc.
Aligning the appliance doors
59
 
						

							aadapter cabinet
bappliance
ckitchen cabinet
dwall
The appliance can be installed in any
fitted kitchen. To match the appliance
to the height of the fitted kitchen, a
suitable adapter cabinetacan be
installed over the appliance.
A ventilation gap of at least 2 inches
(50 mm) must be provided between the
adapter cabinet and the kitchen wall.
The ventilation cross-section below the
room ceiling must be at least 46 in
2
(300 cm2) so that warm air can escape
without obstruction. Otherwise the
appliance has to work harder, which
results in increased energy
consumption.
The ventilation cross-sections must
not be blocked or covered in any
way.
They also need to be
dusted/cleaned on a regular basis.
If installing with standard kitchen
cabinets (max. depth 580 mm), the
appliance can be set up directly next to
the kitchen cabinet. In that case the
side of the appliance door would
project 34 mm and the middle of the
appliance 55 mm beyond the front of
the kitchen cabinet. This allows the
appliance door to open and close
properly.
If the appliance is installednext to a
walld, a gap of at least 55 mm is
needed on the hinge side between the
walldand the applianceb. This
allows space for the handle when the
door is open.
Installing the appliance
60