Miele Kfn 14943 Sd Operating And Installation Instructions

							. . . the frozen food thaws because it
is too warm in the freezer section?
^Did the room temperature drop below
that for which the appliance was
designed?
Increase the room temperature.
The compressor will run less often if the
room temperature is too low. Therefore
it may become too warm in the freezer
section.
. . . food has frozen to the freezer
floor or walls?
Use a blunt instrument (such as a
spoon handle) to carefully pry the items
off.
. . . the alarm sounds and the alarm
off button is flashing?
A temperature section is too warm
because, for instance,
^the appliance door has been opened
frequently, or a large amount of fresh
food has been put in all at once for
freezing.
^
the ventilation slits are blocked.
When the problems have been solved,
the alarm and the displays go out.
. . . bars light up in the temperature
displays?
Check the temperature display approx.
6 hours after the appliance has been
switched on. Only temperatures within
the range the appliance can display will
be shown...._F appears in the temperature
display?
This indicates a problem. Call
Customer Service.
. . . the active charcoal filter change
display lights up red?
^Change the active charcoal filters.
If necessary, order replacement filters
from your Miele dealer.
...nA appears in the temperature
display?
The temperature has risen too high at
some point during the past few hours or
days because of a power outage.
^While nA is illuminated, press the
audio alarm off button.
The temperature display will show the
warmest temperature recorded in the
freezer section during the power
outage.
Depending on the temperature, check
to see whether the food in the freezer
thawed partially or completely. If that is
the case, cook the food before
refreezing it.
The warmest recorded temperature will
appear in the display for approx.
1 minute. Then the display will revert to
the actual current temperature in the
freezer section.
Troubleshooting
41
 
						

							...dn appears in the temperature
display?
The demo mode is activated.
^Call Customer Service.
. . . the appliance cannot be switched
off?
The safety lock is activated.
. . . the interior lighting in the
refrigerator section is not working?
^Was the appliance door left open for
a long time? The lighting
automatically switches off if the door
has been open for approx.
15 minutes.
If that is not the reason, then the interior
lighting is defective.
^Unplug the appliance, or turn off the
respective circuit breaker of the
house wiring system.
^
Remove the front panel.^Pull out the glass plate.
^Unscrew the light bulb and replace it
with a new one.
Light bulb specifications:
110 - 120 V, max. 25 W, E 14 base.
^Slide the glass plate in again.
^Replace the panel and engage the
catches.
. . . the floor of the refrigerator
section is wet?
The drain hole is blocked.
^Clean the condensate channel and
the drain hole.
If a malfunction cannot be corrected
using this troubleshooting guide,
please contact Miele Customer Ser-
vice.
To prevent cold from escaping,
open the appliance doors as little as
possible until the malfunction has
been corrected.
Troubleshooting
42
 
						

							Normal noises What causes them?
Brrrrr...Humming noise made by the motor (compressor). This noise
may get louder for brief periods, whenever the motor kicks in.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds occur whenever the thermostat switches the
motor on or off.
Sssrrrrr....In multi-zone and frost-free appliances, the movement of air
circulating through the appliance can sometimes just barely be
heard.
Please bear in mind that a certain amount of noise is unavoidable (from the
compressor, and the coolant circulating through the system).
Noises that you can
easily rectifyWhat causes them, and what can you do about
them?
Rattling, vibratingThe appliance is uneven: Balance the appliance using a level,
and by raising or lowering the screw feet underneath the
appliance, or placing something underneath them.
The appliance is touching another appliance or piece of
furniture: Move it away.
Drawers, baskets, or shelves are unstable or sticking:Check all
removable items and refit them correctly.
Bottles or containers are unstable or knocking against each
other: Separate them.
The transport cable clips are hanging loose at the back of the
appliance: Remove the clips.
Noises
43
 
						

							In the event of a fault which you cannot
easily fix yourself, please contact the
Miele Technical Service Department at
the address on the back of this booklet.
When contacting the Technical Service
Department, please quote the model
and serial number of your appliance
given on the data plate inside the
appliance.
After sales service
44
 
						

							,Avoid the risk of electrical shock
- Plug into a grounded 3-prong
outlet.
- Do not move the ground plug.
- Do not use an adapter.
- Do not use an extension cord.
Failure to follow these instructions
can result in death, fire, or electrical
shock.
Improper connection of the
equipment grounding conductor
may result in electric shock.
If you are in any doubt as to whether
the appliance has been properly
grounded, have the appliance
checked by a qualified electrician or
service technician.
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer will
not be held responsible for damage
or injury arising from unauthorized
work.
Before installing the appliance,
verify that the voltage, load and
circuit rating information found on
the data plate match the household
electrical supply.
If there are any questions regarding the
electrical connection of this appliance
to the power supply, please consult a
licensed electrician or call the Miele
Technical Service.
V1-800-565-6435The appliance is supplied with a
UL-listed, 3-wire power cord and
NEMA 5-15 P plug ready for connection
to a 120 V, 60 Hz supply.
The fuse rating is 15 amps.
The appliance requires a 3-wire
receptacle.
The receptacle must be installed by a
licened electrician only.
In the case of side-by-side installations,
a separate outlet must be used for each
appliance.
Ideally, the power outlet should be next
to the appliance and easily accessible.
Do not connect the appliance to the
power supply by an extension cord.
Extension cords do not guarantee the
required safety of the appliance
(danger of overheating).
If any changes are needed to the
household wiring or power supply, this
work must be performed by a qualified
electrician.
Electrical information
45
 
						

							Do not place any devices that
produce heat (such as a toaster or
microwave) on top of the appliance.
This would increase the energy
consumption of the appliance!
This fridge/freezer should not be
placed side-by-side with a second
model.
Because the appliance does not
have heated side walls, a
side-by-side arrangement can lead
to the build-up of condensation
water.
Contact your dealer for advice.
Location
The appliance should not be installed
directly next to a heat source (such as
a kitchen range or a heater) or in direct
sunlight. The higher the ambient
temperature, the longer the appliance
will run and the higher the energy
consumption.
Choose a dry, well-ventilated room for
installation.
Climate range
The appliance is designed for use
within a certain climate range (room
temperature range) and should not be
used outside this range. The climate
range is stated on the data plate inside
the appliance.
Climate range Room temperature
SN
N
ST
T+10 °C to +32 °C
+16 °C to +32 °C
+16 °C to +38 °C
+16 °C to +43 °C
If the room is too cold, it will cause the
cooling system in the appliance to
switch off for too long. This may lead to
higher temperatures in the appliance
and the frozen food may even start
thawing!
Proper ventilation
The air behind the appliance gets
warm. In order to ensure adequate
ventilation, you must make sure that the
ventilation slits are not covered or
blocked in any way.
Also, the ventilation slits must be
dusted/cleaned on a regular basis.
Installation
^First remove any cable clips from the
rear of the appliance.
^Check that all the parts on the rear of
the appliance are free to move.
Remove any obstructions.
^Gently slide the appliance into the
desired location.
^
The rear of the appliance can be
directly against the wall.
Installation information
46
 
						

							Adjustments
^Use the wrench provided to adjust
the feet as needed, so that the
appliance is level.
^If necessary, unscrew the foota
from the hinge bracket in order to
support the appliance door.
Installation information
47
 
						

							Appliance dimensions
ABC
KFN 14943 SD ed2020 750 630
Installation information
48
 
						

							The appliance comes with right-hand
hinging. If left-hand door hinging is
preferred, then follow these instructions
to change the door hinge:
You will need the following tools:
–a crosstip screwdriver,
–a flathead screwdriver,
–various sizes of Torx screwdrivers,
–a fork wrench.
Always change the door hinging
with the assistance of another
person.
Removing the door handles:
^
When you pull on the door handlea,
the sidebarbmoves backwards.
^
Pull the sidebarbbackwards out of
the track.
^
Now loosen the 4 screws (Torx 15) in
the mounting plate and remove the
handle.
^
Remove the covers from the opposite
side and place them on the holes that
are now vacant.
Changing the door hinging
49
 
						

							Before changing the hinging,
remove any items of food from the
shelves in the appliance door.
Removing the top soft-close
mechanism:
^Open the top door of the appliance.
^Loosen the panelafrom the
soft-close mechanism: From below,
slide a flathead screwdriver into the
recesses, then slowly and carefully
lift off the panel.
Be careful not to damage the door
seal.
If the door seal is damaged, the
appliance door may not close
properly and there will not be
enough refrigeration!^Slide the panelain the direction of
the appliance and leave it hanging
between the door and the appliance.
^Place the securing deviceb
(supplied with the appliance) on the
soft-close mechanismcso that it
engages.
With the securing device in place, the
joint cannot snap shut. Do not remove
the securing device until instructed to!
^
Using a flathead screwdriver,
carefully lift the top and the bottom of
the coverdfrom the retainer.
^
Push the pineup and out using a
flathead screwdriver.
Changing the door hinging
50