Miele Kf 1901 Vi Operating And Installation Instructions

Mark the distanceXon the back-side
of the custom door.
Also calculate and mark the center of
the custom doorY.
Remove the mounting frame from the
appliance door and position it
according to the markings on the
custom door.
Pre-drill the holes.

Tightly screw on the bracket using
the pre-drilled holes:
Attach the bracket to each
attachment point with at least one
screw.

Attach the bracket at the top with at
least 10 screws.
Please note: When attaching the
mounting frame onto two adjacent
doors (see...

Attaching and aligning the
custom door front
Open the door and hang the custom
door with the mounting frame over
the threaded bolts.
Put the side stripsback into place
and screw them completely down on
both sides of the appliance door.
Bag E contains spare screws for this
purpose.

Screw the nutsa few turns onto
the threaded bolts. Do not tighten
the nuts completely.

Close the appliance door and check
the distance to doors of adjacent
furniture/fixtures.Align the custom door height with the...

Note the size of the upper custom door
front:
Measure the distanceYbetween the
adjusting rail from the lower door and
the upper door.
Be sure to leave a distance of 1/8
(3 mm) from the upper cabinetry
door.
Attaching the lower bracket
(Only for appliances using the Front
panel gap kit.)The fixing brackets are used to secure
the custom door front to the bottom of
the appliance door.
Open the appliance door all the way.
Slightly loosen the screw (1.).
Position the fixing bracket on the
appliance door...

Attaching the covers
To mount the cover strips on both
sides of the upper and lower doors,
click them into place from bottom to
top, into the gap between the
appliance door and the custom door.

Screw the brackets onto both sides
of the appliance, to hold the cover
strip.Insert the cover strip into the space
between the appliance and the side
panel.
For side-by-side combinations, the
cover strips (on both sides of the
appliance) are applied to the
outermost spaces only.

Attach the light switch...

Insert the cover plate on the freezer
compartment door.
Attaching the toe-kick cover
The maximum height of the toe-kick
cover is 4 (101 mm) from the top of
the floor. Do not cover the ventilation
slits in the plinth. Risk of damage to
the appliance.

If required, cut the toe-kick cover to
the required length and height.

Attach the plinth to the appliance,
and put the included cover plates in
place.Remove the foil from the adhesive
strips.
Attach the toe-kick cover to the
plinth.
Installing the...

Mounting the air separator
The air separator keeps the supply and
exhaust air separate. This prevents
warm exhaust air from flowing into the
machine, optimizing the energy
performance of the unit.
If necessary, shorten the three parts
of the air separator.

Insert the foam pieces back into the
sides.Clip the air separator, left and right of
the partition, in the exhaust grille. Be
sure that it clicks into place and
guides the foam partition under the
exhaust grille.
Installing the appliance
76
 

All plumbing work should be carried
out by a suitably qualified and
competent person, in accordance
with all applicable local and national
regulations.
The water quality must conform to
country requirements for drinking
water.
–The appliance is only suitable for
connection to the cold water supply.
– The water pressure must be between
25 and 120 psi (1.72-8.25 bar).
– A separate shut-off valve must be
installed, so that the water supply
can be interrupted as needed.
– The maximum outer diameter of the...

Preparing the water connection
The connection to the household
water supply must be installed
before the appliance is installed.
Turn off the main water valve to prevent
damage caused by leaking water.
Attach the connecting pipe to the
shut-off valve, according to the
instructions supplied by the
manufacturer of the ice cube maker
installation kit.
Install the connecting pipe. Always
observe the indicated clearance
dimensions to prevent damage to the
connecting pipe when pushing in the
appliance.
...

Connecting the water supply
When connecting the water pipe to
the solenoid valve of the appliance,
follow the instructions supplied by
the manufacturer of the ice cube
maker installation kit.
When bending the water pipe, be sure
not to kink it, otherwise there is a risk of
leaks and water damage.
Use bending aids.

Remove the cap from the appliance
connection,1.

Bend the water pipe to suit the
location of the connection on the
appliance,2.Push the union nut and seal onto the
water pipe.
Push the end...

Avoid the risk of electrical
shock
- Plug into a grounded 3-prong
outlet.
- Do not move the ground plug.
- Do not use an adapter.
- Do not use an extension cord.
Failure to follow these instructions
can result in death, fire, or electrical
shock.
Improper connection of the
equipment grounding conductor
may result in electric shock. If you
are in any doubt as to whether the
appliance has been properly
grounded, have the appliance
checked by a qualified electrician or
service technician.
Installation,...