Miele H 5981 Bp Manual

The approximate finish time can be
estimated, as the duration of a cooking
programme using the food probe
corresponds more or less to the
duration of the same programme
without the food probe.
The Duration and Finish cannot be
entered as the total time depends on
how long it takes for the core
temperature to be reached.
Time left display
After a certain time the estimatedtime
remaining, appears in the oven
display.
The actual core temperature is no
longer displayed and cannot be called
up.
The time...

The Moisture plus function uses a
steam injection system.
Water is taken into the steam injection
system via the tube underneath the
control panel on the left. The water is
then injected as bursts of steam into the
oven compartment during the cooking
process.
The steam inlets are located at the rear
left corner of the roof of the oven.
Only use water with this function.
Other liquids will damage the
appliance.
Baking, roasting or cooking with
Moisture plus uses just the right amount
of steam and optimum...

Automatic programmes
Automatic programmes with Moisture
plus set the optimium temperature, the
degree of moisture and also the
duration automatically.
At the beginning of the programme you
will be prompted to allow a specified
amount of water to be drawn into the
oven.
The amount of water specified will be
more than the amount which is actually
needed which means that some of the
water will remain in the container as not
all of it will be drawn up into the oven.
The programme will control how many
bursts...

Moisture plus
When using the Moisture plus function
you will need to enter
–the temperature (at least 130 °C),
and
–the number of bursts of steam.
You can also enter the cooking duration
or you can use the food probe.
Number of bursts of steam and when
they are injected
The number of bursts of steam and
when they are injected will depend on
the type of food being cooked:
–Dough mixtureswill rise better if
steam is injected at the beginning of
the programme.
–Bread and rollsalso rise better if
exposed to...

Using Moisture plus
Place the food in the oven.
Select Moisture plus.
Select a temperature.
Select Automatic burst of steam or
select the number of bursts of steam.
Fill a suitable container with the
quantity of water specified.
Automatic/
1 burst of steam: approx. 100 ml
2 bursts of steam: approx. 150 ml
3 bursts of steam: approx. 250 ml
Pull the fill tube forwards (located
below the control panel on the left).

Hold a container with the quantity of
water specified under the tube as
shown....

To evaporate residual moisture
If there is still water in the steam
injection system at the end of a
programme or if the programme is
cancelled, you will be prompted to
evaporate the residual moisture.
This prompt will appear
–when the appliance is switched on,
–when selecting Moisture plus, or
–when selecting an automatic
programme that uses Moisture plus.
Select Cancel to cancel the process
or OK to start it.
It is best to start the evaporation
process straight away so that only
fresh water can be used...

To cancel the residual moisture
evaporation process
After the appliance has been
switched on, the prompt to evaporate
residual moisture will appear in the
display. Touch the sensor next to
Cancel. You will only be able to run
functions and Automatic programmes
without Moisture plus.
If you select Moisture plus or one
of the Automatic programmes with
Moisture plus, the prompt to evaporate
residual moisture will appear immedi
-
ately.
If you do not want to start the residual
moisture evaporation process,...

The minute minder can be used to time
any activity in the kitchen, e.g. boiling
eggs.
You can enter a time of up to a
maximum of 9 hours, 59 minutes and
59 seconds.
You can set the minute minder at the
same time as another timed
programme, e.g. as a reminder to stir a
dish or add seasoning etc.
With Moisture plus, it is a good
idea to use the minute minder to
remind you when to release the
bursts of steam manually.
To set the minute minder
Touch thesensor.
0 : 00 : 00 will appear in the display....

Your appliance is supplied with a
number of standard default settings.
To change a setting:
Select the Settings option.
The list of options will show in the
display.
Language
Time
Lighting
Main menu
Catalyser
Cooling fan run-on
Pyrolytic
Heating-up phase
Start
Recommended temperatures
Display
Volume

Speedlight

Safety

Units

Showroom programme

Factory default

Select and confirm the one you want
to change.
If a setting is not confirmed within a
certain time, the display will...

Time (of day) display
Select how you want the time to appear
in the display when the oven is
switched off:
On
(Factory default)
The time will always show in the
display.
On for 60 seconds
The time is only ever visible for 60
seconds when the oven is switched
on and when it is switched off.
Do not display
The time will only show in the display
when the oven is being operated.
Clock format
The time can be altered from a 24-hour
display to a 12-hour display:
12 h: 12 hour clock display
24 h: 24 hour...