Miele H 5461 Bp Manual

							To use Automatic switch-off
Toswitch a programme off
automaticallyselect Duration or Finish
and enter the time required.
Example:
The time is 11:45. Your dish will take
30 minutes to cook, and needs to be
ready at 12:15.
Select Duration, and enter 0:30 h, or
select Finish and enter 12:15.
The oven will switch off automatically at
the time set.Delaying the start with Automatic
switch-off
We recommend using automatic
switching on and off when roasting.
However, do not delay the start for
too long when baking as the cake
mixture or dough will dry out, and
the raising agents will lose their
effectiveness.
Toswitch a programme on and off
automaticallyyou have various
options:
–Enter the Duration and Finish time.
– Enter the Start time and the Duration.
– Enter the Start time and the Finish.
Example:
The time is 11:30. Your dish will take
30 minutes to cook, and needs to be
ready at 12:30.
Select Duration and enter 0:30 h.
Then select Finish and enter 12:30 h.
The Start time will be calculated
automatically. Start at 12:00 will
appear in the display.
The cooking programme will start at this
time.
More about manual operation
31 
						

							Sequence of the cooking programme
when using Automatic switch-off
The following will appear in the display:
Before the programme starts
–The cooking function and selected
temperature
–Start at and the start time
After the programme has started
–The heating-up phase until the set
temperature is reached
–Once this temperature is reached, a
tone will sound (provided this is
activated - see Settings - Volume -
Buzzer tones).
After the heating-up phase
– The Time left counting down can be
followed in the display,
Shortly before the end of the
programme
– The oven heating switches off.
– The cooking programme continues
using residual heat. The residual
heat in the oven is sufficient to
complete the cooking process.
–
Use residual heat will show in the
display.
–
The cooling fan continues to run, as
does the hot air fan if a Fan setting
has been chosen.
At the end of the cooking programme
–
The hot air fan switches off,
depending on the cooking function
being used.
–
The Prog. finished message will
appear in the display.
–
A tone will sound (provided this is
activated - see Settings - Volume -
Buzzer tones).After the programme has finished
–The cooling fan will continue to run
for a while after the oven has been
switched off to prevent any humidity
building up in the oven, on the
control panel or in the oven housing
unit.
The fan is temperature controlled
and will switch off automatically. You
can change the default setting for
this (see Settings - Cooling fan
run-on).
–To save energy, the oven will switch
off automatically if it is not used
again within a certain time.
The timing depends on the settings
selected (cooking function,
temperature, duration).
Changing or deleting an entered
cooking time
Touch the OK sensor.
Select Duration with the OK sensor.
Use thesensor to set the time to
-:- -.
If there is a power cut, all data entered
will be deleted.
More about manual operation
32 
						

							Activating moisture reduction
It is a good idea to use this function
when cooking items which are moist on
the inside but which should be crispy
on the outside, e.g. frozen chips,
croquettes or pork with crackling.
It is also suitable for deep filled fresh
fruit cakes, such as plum or apple
cake.
You can activate Moisture reduction
with any function.
For best results, activate it at the
beginning of the cooking
programme.
Place the food in the oven.
Select the required function and set
the temperature.
Touch the OK sensor.
The list of options will show in the
display.

Use theorsensor to select
Moist.reduction, and confirm with
the OK sensor.

Use theorsensor to select On,
and confirm with the OK sensor.
More about manual operation
33 
						

							The Moisture plus function uses a
steam injection system.
Water is taken into the steam injection
system via the tube underneath the
control panel on the left. The water is
then injected as bursts of steam into the
oven compartment during the cooking
process.
The steam inlets are located at the rear
left corner of the roof of the oven.
Only use water with this function.
Other liquids will damage the
appliance.
Baking, roasting or cooking with
Moisture plus uses just the right amount
of steam and optimum air flow for very
even cooking and baking results:
delicious fresh bread with a glossy
crust; rolls and croissants as good as
the baker makes; tender, succulent
meat with a well browned finish;
perfectly finished oven bakes; delicious
soufflés and much more.
Please refer to the Moisture plus
booklet supplied with your oven for
further information and a selection of
recipes.
Moisture plus is not suitable for
mixtures which already contain a lot of
moisture, such as choux pastry and
meringues, as the addition of steam
does not allow them to dry out
sufficiently.
Moisture plus is activated with
Automatic programmes or you can
select the special Moisture plus
function.
The steam injection system should
be rinsed through before you use an
Automatic programme with Moisture
plus or the Moisture plus function for
the first time.
To do this, run the oven using
Moisture plus - 160 °C - Automatic
burst of steam for about 30 minutes.
Automatic programmes
Automatic programmes with Moisture
plus set the optimium temperature, the
degree of moisture and also the
duration automatically.
At the beginning of the programme you
will be prompted to allow a specified
amount of water to be drawn into the
oven.
The amount of water specified will be
more than is actually needed leaving a
small amount in the container.
The programme will control how many
bursts of steam are required and at
what point they are injected.
Moisture plus
34 
						

							Moisture plus
To use the Moisture plus function, a
temperature of at least 130 °C and the
number of bursts of steam need to be
entered.
You can also enter the cooking duration
or you can use the food probe.
Number of bursts of steam and when
they are injected
The number of bursts of steam and
when they are injected will depend on
the type of food being cooked:
–Dough mixtureswill rise better if
steam is injected at the beginning of
the programme.
–Bread and rollsalso rise better if
exposed to steam at the start.
Injecting a burst of steam at the end
of the programme will give the bread
and rolls a glistening crust.
– Whenroasting meat with a high fat
contentinjecting steam at the
beginning of roasting will draw out
the fat.
Please refer to the sample recipes in
the Moisture plus booklet.After selecting Moisture plus you need
to set the number of bursts of steam.
The options are:
Automatic
This requires enough water for one
burst of steam. The burst of steam
will be injected into the oven
automatically after the heating-up
phase.
Steam is injected for about 5
minutes.
1 burst of steam
2 bursts of steam
3 bursts of steam
The quantity of water required will
depend on the number of bursts of
steam.
The earliest point at which steam can
be injected is after the heating-up
phase has been completed.
One burst of steam takes approx.
5 minutes to be injected into the
oven.
It is a good idea to set the minute
minder to remind you when to inject
the bursts of steam required.
It is quite normal for condensation to
form on the inside of the door during
steam injection. This will dissipate
during the course of the cooking
programme.
Moisture plus
35 
						

							Using Moisture plus
Place the food in the oven.
Select Moisture plus.
Moisture plus (highlighted) and
Descale will show in the display.
Touch the OK sensor.
Select Automatic burst of steam or
select the number of bursts of steam.
Touch the OK sensor.
Select a temperature.
Fill a suitable container with the
quantity of water specified.
Automatic/
1 burst of steam: approx. 100 ml
2 bursts of steam: approx. 150 ml
3 bursts of steam: approx. 250 ml
Pull the fill tube forwards (located
below the control panel on the left).

Hold a container with the quantity of
water specified under the tube as
shown. Start the water intake process
with OK.The amount of water required will be
drawn up into the oven. The segment
display shows how the process is
progressing.
The quantity of water specified is higher
than actually required, leaving a small
amount in the container.
When you close the oven door you will
hear the noise of the pump briefly.
–Automatic burst of steam
Once the heating-up phase has been
completed, the automatic burst of
steam is injected and the water will
vaporise in the oven compartment.
Once the steam has been injected
successfully, the programme will
continue to the end.
– Injecting bursts of steam manually
As soon as Burst of steam shows in
the display after the heating phase,
steam can be injected at the intervals
given in the recipe.
Set the minute minderas a reminder.
At time time specified:

Touch the OK sensor.
The water will vaporise in the oven
compartment.
If more bursts of steam are required,
proceed as described above.
Once the steam has been injected
successfully, the programme will
continue to the end.
Moisture plus
36 
						

							Evaporate residual moisture
If there is still water in the steam
injection system at the end of a
programme or if the programme is
cancelled, you will be prompted to
evaporate the residual moisture.
When you turn the function selector to
0, the instruction to select Moisture
plus in order to evaporate the residual
moisture appears in the display.
Confirm this with OK.
This message will appear every time
the function selector is turned to 0
after a cooking programme until the
evaporation process is run.
The message Evaporate residual
moisture also appears when
– selecting Moisture plus, or
– selecting an automatic programme
that uses Moisture plus.
You have the option to start to
evaporate the residual moisture or to
cancel this.
It is best to start the evaporation
process straight away so that only
fresh water can be used during the
next cooking programme.The residual moisture evaporation
process
When the residual moisture is
evaporated, the oven heats to approx.
150 °C, and the residual water
evaporates inside the oven.
This can take up to 30 minutes,
depending on the amount of water in
the system.
Steam will condense on the door
and the oven cavity, and the
moisture will then need to be wiped
off after the oven has cooled down.
To start the residual moisture
evaporation process
Select Moisture plus.
Confirm the prompt to Evaporate
residual moisture by touching the
OK sensor.
The evaporation of the residual
moisture will start straight away.
The display will show the approximate
time remaining.
After the residual moisture has
evaporated, the Moisture plus option
will show in the display.

Turn the function selector to 0.
Moisture plus
37 
						

							To cancel the residual moisture
evaporation process
If you select Moisture plus or one of
the Automatic programmes with
Moisture plus, the prompt to evaporate
residual moisture will appear.
Touch theoderfor at least 3
seconds.
The evaporation process will be
cancelled.
The cooking programme can now be
started.
Do not cancel the prompt for
residual moisture evaporation too
often, as this might cause the steam
unit to overflow when taking in more
water.
Descaling
The oven will need to be descaled
depending on the number of cooking
programmes using Moisture plus which
have been run and the amount of water
taken into the oven for these. A
message to tell you to descale the
appliance will appear in the display.
The steam injection system should be
descaled regularly. How often this
needs to be done will depend on the
water hardness level in your area.
You can start the descaling process at
any time by selecting the Moisture plus
function and then Descale.
You cannot use the oven until you have
carried out the descaling process.
See Cleaning and care for more
information about descaling.
Moisture plus
38 
						

							The minute minder can be used to time
any activity in the kitchen, e.g. boiling
eggs.
You can enter a time of up to a
maximum of 9 hours and 59 minutes.
You can set the minute minder at the
same time as another timed
programme, e.g. as a reminder to stir a
dish or add seasoning etc.
With Moisture plus:
It is a good idea to use the minute
minder to remind you when to
release the bursts of steam
manually.
To set the minute minder
Touch thesensor.
0 : 00 : 00 h : min : sec
comes up in the display.
The hour is highlighted.
Use theorsensors to first select
the hour, and confirm your selection
with the OK sensor.
After setting the hour, the minutes will
be highlighted.

Now use theorsensors to select
the minutes, and confirm your
selection with the OK sensor.
After setting the minutes, the seconds
will be highlighted.

Finally, use theorsensors to
select the seconds, and confirm your
selection with the OK sensor.The time counts down in the display.
At the end of the time set for the minute
minder
–thesymbol will flash.
–A signal will sound (provided this is
activated - see Settings - Volume -
Buzzer tones).
–the display will show the time
counting upwards.
Touch thesensor.
To alter the time set for the
minute minder:
Touch thesensor.
Use thesensor to scroll the minute
minder through to -:--:--,and
then set the hour, minutes and
seconds, confirming each entry with
OK.
To cancel the time set for the
minute minder

Touch thesensor.

Use thesensor to scroll the minute
minder through to -:--:--.

Touch the OK sensor.
Minute minder
39 
						

							Your appliance is supplied with a
number of standard default settings.
Settings cannot be altered while a
cooking programme is in progress.
To change a setting:
Select Settings.
The list of options will show in the
display.
–Language
–Time
–Lighting
– Catalyser
– Cooling fan run-on
– Pyrolytic
– Heating phase
– Recommended temperatures
– Display
–
Volume
–
Safety
–
Temperature format
–
Showroom programme
–
Factory default

Select the setting that you want to
change by touching theoder
sensor, and confirm with OK.Use theorsensor to select the
setting you want and confirm with the
OK sensor.
Settings which are currently selected
are marked with a.
If you do not make another selection
within approx. 15 seconds after
selecting a setting, the display will
return to the Settings list.
Language
You can set the language you want the
display to appear in.
After selecting and confirming
Language, the language you have
selected will appear in the display.
If you have selected the wrong
language by mistake, you can follow
the flag symbolto get back to the
Languagemenu.
Settings
40